Installation Instructions

ManualsBrandsToro ManualsAttachmentsGrass Collection System, Reelmaster 2300/3100-D

FormNo.3380-654RevA

GrassCollectionSystem

Reelmaster

2300/3100-D

ModelNo.03227

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Rollerbumperassembly1

Flangeheadscrews-M8x162

Mounttherollerbumper(Reelmaster

3100Donly)

Nopartsrequired

–

Tensionthecounterbalancesprings

Nopartsrequired

–

Adjustthefrontcuttingunitshields

Frontbasketbracket–L.H.2

Frontbasketbracket–R.H.2

Capscrew–5/16x1inch

Locknut8

Frontgrassbasketassemblies2

Mountthefrontgrassbaskets

(Reelmaster3100Donly)

Frontbasketbracket–L.H.2

Frontbasketbracket–R.H.2

Capscrew–5/16x1inch.

Locknut4

Frontgrassbasketassemblies2

Mountthefrontgrassbaskets

(Reelmaster2000Dseriesonly)

Nopartsrequired

–

Optionalbasketwheel

45degreeFittingw/O–rings

Changethehydraulictting(Reelmaster

3100Donly)

Nopartsrequired

–

Adjustreargrassshield

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

*3380-654*A

Summary of content (12 pages)

PAGE 1
Form No. 3380-654 Rev A Grass Collection System Reelmaster® 2300/3100-D Model No. 03227 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 7 8 © 2014—The Toro® Company 8111 Lyndale Avenue South Bloomington, MN 55420 Description Qty.
PAGE 2
Procedure Description Use Qty. Rear basket bracket assembly–L.H. Rear basket bracket assembly–R.H.
PAGE 3
2 3 Tensioning the Counterbalance Springs Adjusting the Front Cutting Unit Shields (Reelmaster 2000D series only) No Parts Required No Parts Required Procedure Procedure 1. Remove the mounting screws securing the front of each front cutting unit shield to the frame (Figure 3). Important: The additional weight of the baskets when installed on the cutting units may require a change in counterbalance. Raise the counterbalance springs one or two holes at both ends (depending on turf conditions). 2.
PAGE 4
3. Latch each hanger bracket over notch on carrier frame (Figure 4). 4 Note: Adjust the sliding hanger brackets so the bottoms of the front baskets are parallel or slightly elevated with the ground. Mounting the Front Grass Baskets 5 (Reelmaster 3100D only) Parts needed for this procedure: 2 Front basket bracket–L.H. 2 Front basket bracket–R.H.
PAGE 5
6 1 3 Optional Basket Wheel No Parts Required 4 Procedure An optional Basket Wheel Kit, Part Number 5–2893 (Figure 7) is available from your local Toro Distributor. Each basket wheel is mounted to the basket bracket with (2) capscrews, flat washers and locknuts. Two rollers are required per basket. Part numbers for the required components can be found in the Parts Catalog. 2 g025820 Figure 5 3. R.H. Basket bracket 4. Front sliding hanger bracket 1. Carrier frame 2. L.H.
PAGE 6
8 2 3 Adjusting the Rear Grass Shield 1 No Parts Required Procedure • In wet conditions, adjust the rear shield all the way up. • In dry conditions, the rear shield may need to be slightly lowered to the insure clippings are thrown into the rear of basket. Adjust as required. g025823 Figure 8 1. Rear cutting unit motor 3. Straight fitting 9 2. Rear hydraulic line 2. Remove the straight fitting from the motor (Figure 8). Mounting the Rear Grass Basket 3.
PAGE 7
3 3 4 1 2 1 2 g025827 4 Figure 12 1. Rear carrier frame 3. Rear sliding hanger bracket (2) 2. Basket bracket assembly (2) 4. Basket pins g025825 Figure 10 1. Strap 3. Cable tie 2. Strap bolt 4. Wood block 4. Adjust the basket brackets so the bottom of the lower basket flap contacts the top of the roller.
PAGE 8
1 Figure 14 1. Roller bumper 3. Sliding hanger bracket carriage bolt nuts 2. Wear strip Figure 13 2. Rotate the basket until the roller contacts the middle of the wear strip (Figure 14). 3. Tighten the carriage bolt nuts to secure the basket position. 1. Roller bumper 11 Verify that the roller bumper contacts the wear strip when raising the cutting unit and when the cutting unit is fully raised.
PAGE 9
2. Rock the basket backward to lift the basket pins out of the basket brackets (Figure 16). 1 2 ballast. Use the following chart to determine the weight or combinations of weights needed. Weight Kits Required Standard machine with 27 inch cutting units & baskets (1) 83-9370 (3) 83-9390 (2) 94-3698 Standard machine with three wheel drive kit & 27 inch cutting units (1) 83-9390 (1) 83–9370 Note: All configurations require calcium chloride in the rear tire.
PAGE 10
Notes: 10
PAGE 11
Notes: 11
PAGE 12