Form No. 3430-932 Rev A Operator Cooling Fan Groundsmaster® or Reelmaster® Traction Unit with Universal Sunshade Model No. 03247 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 7 8 © 2019—The Toro® Company 8111 Lyndale Avenue South Bloomington, MN 55420 Description Qty. Use No parts required – Prepare the machine. No parts required – Remove the sunshade.
1 Preparing the Machine No Parts Required Procedure 1. Park the machine on a level surface. 2. Shut off the engine, engage the parking brake, and remove the key from the ignition switch. 3. Disconnect the battery; refer to the electrical system maintenance section of your Operator’s Manual. g244328 2 Figure 2 Removing the Sunshade 1. Grommet 3. Washer (5/16 inch) 2. Flange-head bolt (5/16 x 1-1/4 inches) 4. Clip nut (side-frame channel) 2.
4. 4 Align the holes in the fan mount brackets to the hole in the switch panel as shown in Figure 4. Installing the Cooling Fan, Fan Switch, and Fan-Speed Controller Parts needed for this procedure: 1 Long fan-mount bracket 1 Cooling fan 1 Short fan-mount bracket 4 Carriage bolt (1/4 x 5/8 inch) 4 Flange locknut (1/4 inch) 1 Fan switch 1 Jam nut g244454 Figure 4 1 Knob 1 Fan-speed controller 2 Thread-forming screw (#8 x 3/8 inch) 1. Flange locknut (1/4 inch) 4.
2. Insert the fan-switch shaft through the hole in the panel and secure the switch with the jam nut (Figure 5). 3. Align the D-shaped hole in the knob with the flat on the inner shaft of the fan-switch shaft (Figure 5). 4. 5 Installing the Wire Harness and Fuse Press the knob onto the switch until knob is fully seated (Figure 5). Parts needed for this procedure: Installing the Fan-Speed Controller 1.
g244634 Figure 10 g283647 Figure 8 1. Violet (wire-harness terminal labeled RESISTOR MODULE L) 6. Blade terminal 5—Motor (fan-speed controller) 2. Blade terminal 1 (Low—fan-speed controller) 7. Pink (wire-harness terminal labeled MOTOR (+)) 3. Blade terminal 2 (Medium—fan-speed controller) 8. Orange (wire-harness terminal labeled RESISTOR MODULE H) 4. Blade terminal 3 (High 1—fan-speed controller) 9. Brown (wire-harness terminal labeled RESISTOR MODULE M) 5.
Installing the Fuse • If the airstream position is correct, shut off Inset the fuse (25 A) into the fuse block at the second fuse slot from the left (Figure 11). • If the operator wants the airstream of the the cooling fan. cooling fan moved, perform the following steps: Note: The fuse may not need to be installed if a fuse has already been installed from another Toro kit. A. Shut off the cooling fan. B.
g244666 g244327 Figure 13 D. E. Figure 14 Assemble the switch panel to the side-frame channels with the carriage bolts and locknuts (Figure 12) that you removed in step 3B. 1. Sunshade 3. Washer (5/16 inch) 2. Flange-head bolt (5/16 x 1-1/4 inches) 4. Clip nut (side-frame channel) 3. Torque the flange locknuts to 1017 to 1243 N∙cm (90 to 110 in-lb). Torque the flange-head bolts to 1017 to 1355 N∙cm (90 to 120 in-lb).
Declaration of Incorporation The Toro Company, 8111 Lyndale Ave. South, Bloomington, MN, USA declares that the following unit(s) conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain Toro models as indicated on the relevant Declarations of Conformity. Model No. 03247 Serial No.
