Installation Instructions

ManualsBrandsToro ManualsAttachmentsFlexible Bottom Grass Basket Kit, Reelmaster 5010 Series 22in Cutting Units

FormNo.3413-602RevA

FlexibleBottomGrassBasketKit

Reelmaster

5010Series22inCuttingUnitsand3550/5010-H

Series22inRearCuttingUnits

ModelNo.03415

ModelNo.03416

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Cylindercollar

Bolt4

Flangelocknut8

Spacer

Stopbracket

Carriagebolt

Installtherearliftcylinderlimitkit

(orderedseparately).

Basketguide—Model034151

Basketbracket—Model034151

Basketbracket—Model034162

Rollpin—Model034151

Rollpin—Model034162

Lefttorsionspring(gold)—Models

03415and03416

Righttorsionspring(black)—Models

03415and03416

Basketcollar—Model034151

Basketcollar—Model034162

Flatwasher(3/8x7/8inch)—Models

03415and03416

Bolt(5/16x1-1/4inches)—Model03415

Bolt(5/16x1/2inch)—Model03415

Bolt(5/16x1/2inch)—Model03416

Plasticwasher—Model034151

Plasticwasher—Model034162

Installthebasketguidesandbrackets.

Cutoffbar

Bolt(1/4x1-3/4inches)

Locknut(1/4inch)

Installthecutoffbar.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3413-602*A

Summary of content (12 pages)

PAGE 1
Form No. 3413-602 Rev A Flexible Bottom Grass Basket Kit Reelmaster® 5010 Series 22in Cutting Units and 3550/5010-H Series 22in Rear Cutting Units Model No. 03415 Model No. 03416 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Installation Loose Parts Use the chart below to verify that all parts have been shipped.
PAGE 2
Procedure 4 5 6 7 8 9 Description Use Qty. No parts required – Remove the 4 grass deflectors (if installed). Spacer Bolt (3/8 x 1-1/4 inches) 2 2 Flange locknut (3/8 inch) 2 Remove the support tube (if installed, for 5 or 7-inch diameter reels only) and installing the new carrier-frame pivot bolt.
PAGE 3
Reelmaster 3555 with 5-inch cutting units and Reelmaster 3575 with 7-inch cutting units Flexible Bottom Grass Basket Kit (for front cutting units) 03415 3 Compact Flexible Bottom Grass Basket Kit (for rear cutting units) 03416 2 131-6845 5 Groomer Rod Kit (only for units with groomers installed) Note: Older Reelmaster 5010 series cutting units may be missing the threaded hole in the front height-of-cut brackets needed to install this kit (Figure 1).
PAGE 4
2 Installing the Basket Guides and Brackets Parts needed for this procedure: g004024 Figure 2 1. Cylinder collar 5. Stop bracket 2. Spacer 6. Deflector bracket 3. Bolt 7. Carriage bolt 4.
PAGE 5
g034183 g003683 Figure 3 Reelmaster 5210/5410/5510/5610 Series Figure 5 1. Center basket 5. Right front basket 2. Left rear basket 6. Basket guide 3. Right rear basket 7. Basket bracket 4. Left front basket 8. Kit 03415 for all (front and rear cutting units) 1. Bolt (5/16 x 1/2 inch) 3. Basket guide 2. Flat washer (3/8 x 7/8 inch) 4. Carrier frame 4. Install a roll pin into the lower hole in the appropriate side of each cutting-unit carrier frame (Figure 6).
PAGE 6
3. Tighten the bolts and locknuts (Figure 7). shorter, rear leg of the spring into the hole in the basket bracket. 6. Ensure that the basket bracket rotates freely. 4 Important: The plastic washer must be installed onto the basket collar to prevent binding.
PAGE 7
5 Installing the New Carrier-Frame Pivot Bolts and Removing the Support Tube (If Installed, for 5 or 7-Inch Diameter Reels) Parts needed for this procedure: 2 Spacer g028885 2 Bolt (3/8 x 1-1/4 inches) 2 Flange locknut (3/8 inch) Figure 9 1. Flange locknut (3/8 inch) 4. Bolt (3/8 x 1-1/4 inches) 2. Carrier frame 5. Support tube 3. Spacer Procedure 1. Unthread the 2 flange-head bolts securing the support tube and the cutting-unit carrier frame to the cutting-unit side plates (Figure 9).
PAGE 8
2. Insert the long hexagonal end of the basket rod into 1 basket plate and the other end into the other basket plate (Figure 10). 7 3. Secure the short hexagonal end of the rod with a flange nut (5/16 inch) and a hardened washer (Figure 10). Installing the Groomer Rod Kit (Units with Groomers Only; Ordered Separately) Important: Ensure that the basket rod does not touch the front roller. Parts needed for this procedure: 1 Groomer rod 1 Bolt (M10 x 12 mm) 2 Washer Procedure 1. Basket rod 4.
PAGE 9
8 9 Mounting the Basket Assembly Adjusting the Basket Position to the Cutting Unit No Parts Required Parts needed for this procedure: 1 Procedure Basket assembly Make sure that the basket is parallel to the cutting unit with a minimum clearance of 6 mm (0.250 inch) between the lip of the basket and the reel.
PAGE 10
Notes:
PAGE 11
Notes:
PAGE 12