Service Manual

Reelmaster 5500-DPage 8 - 10Cutting Units
Adjusting Attitude (New Cutting Units)
Table 1—New Cutting Unit Set Up Guide
Desired Height-of-Cut
(HOC)
Desired
Attitude
Second Screw
“A”
(Fig. 13)
Front Height-of-Cut
Rod “B”
(Fig. 14)
Rear Height-of-Cut
Rod “C”
(Fig. 14)
Rear Support
Bracket
(Fig. 14)
(in) (mm) (degrees) (in) (mm) (in) (mm) (in) (mm) (location)
0.375 (10) 2* 0.18 4.6 1.62 41.3 1.86 47.4 top
4* 0.23 5.9 1.82 46.4 1.62 41.3 top
6* − − 2.02 54.5 1.38 35.2 top
8* − −−−−− top
0.500 (13) 2* 0.29 7.6 1.49 38.1 1.74 44.2 top
4* 0.35 9.0 1.70 43.2 1.50 38.1 top
6* 0.41 10.5 1.90 48.3 1.26 32.1 top
8* − −−−−− top
2 0.22 5.8 1.36 34.5 1.91 48.5 top
4 0.28 7.2 1.56 39.6 1.66 42.4 top
6 0.34 8.7 1.76 39.6 1.42 26.3 top
8 − − 1.96 49.9 1.19 30.3 top
0.625 (16) 2 0.35 9.0 1.23 31.3 1.78 45.3 top
4 0.41 10.4 1.43 36.4 1.54 29.2 top
6 0.46 11.9 1.63 41.6 1.30 24.6 top
8 − − 1.83 46.7 1.06 27.1 top
0.750 (19) 2 0.47 12.1 1.10 28.2 1.65 42.1 top
4 0.53 13.6 1.31 33.3 1.41 36.0 top
6 0.59 15.0 1.51 38.4 1.17 29.9 top
8 0.65 16.5 1.71 43.5
0.94
23.9 top
0.875 (22) 2 0.60 15.3
0.98
25.0 1.53 38.9 top
4 0.66 16.8 1.18 30.1 1.29 45.5 top
6 0.71 18.2 1.38 35.2 1.05 26.8 top
8 0.77 19.7 1.58 40.3
0.81
20.7 top
1.000 (25) 2 0.72 18.5
0.85
21.8 1.40 35.7 top
4 0.78 19.9 1.06 26.9 1.16 29.6 top
6 0.84 21.4 1.26 32.0
0.92
23.6 top
8 0.90 22.9 1.46 37.2
0.69
17.6 top
1.125 (29) 2 0.85 21.7
0.73
18.6 1.28 32.6 top
4 0.91 23.1
0.93
23.7 1.04 26.5 top
6 0.96 24.6 1.13 28.9
0.80
20.4 top
8 1.02 26.0 1.38 35.3
0.56
14.4 top
1.250 (32) 2 0.97 24.8
0.60
15.4 1.15 29.4 top
4 1.03 26.3
0.80
20.5
0.91
23.3 top
6 1.09 27.7 1.01 25.7
0.67
17.2 top
8 1.15 29.2 1.21 30.8
0.44
11.2 top
1.375 (35) 2 1.10 28.0
0.48
12.2 1.03 26.2 top
4 1.16 29.5
0.68
17.4
0.79
20.1 top
6 1.21 30.9
0.88
22.5
0.55
14.0 top
8 1.27 32.4 1.08 27.6
0.31
8.0 top
1.500 (38) 2 1.22 31.2
0.35
9.0
0.90
23.0 top
4 1.28 32.6
0.55
14.2
0.66
16.9 top
6 1.34 34.1
0.76
19.3
0.42
10.9 top
8 1.40 35.6
0.96
24.5
0.19
4.9 top
1.625 (41) 2 − −
0.22
5.8 1.40 35.7 bottom
4 1.41 35.8
0.43
11.0 1.16 29.6 bottom
6 1.42 36.2
0.63
16.2
0.92
23.6 bottom
8 1.52 38.7
0.83
21.3
0.69
17.6 bottom
1.750 (45) 2 − −
0.10
2.6 1.27 32.5 bottom
4 1.53 39.0
0.30
7.8 1.04 26.4 bottom
6 1.59 40.4
0.51
13.0
0.80
20.4 bottom
8 1.65 41.9
0.71
18.1
0.56
14.4 bottom
* Optional Low Cut Bedknife, Toro part no. 93-9774, is required for height-of-cut below 0.500” (13 mm).
 For front (”B”) or rear roller distances (“C”) less than 1” (25 mm) order long cone nut (Part No. 95-2790) to
replace bottom cone nut for improved support.