Installation Instructions

ManualsBrandsToro ManualsRiding ProductsOperator Golf Ball Guard, Reelmaster 3100/3500/5010 or Groundsmaster 3500/4300 Series Traction Unit

FormNo.3411-852RevC

OperatorGolfBallGuard

Reelmaster®3100/3500/5010/7000,Groundsmaster®

3500/4300/4500/4700,andMachineswithaStraightRollBar

ModelNo.03614

InstallationInstructions

PreparingtheMachine

Parkthemachineonalevelsurface,engagethe

parkingbrake,shutofftheengine,andremovethe

keyfromthekeyswitch(Figure1).

g037695

Figure1

AssemblingtheBallGuard

Partsneededforthisprocedure:

Guardassembly

2Flangenut

Shoulderbolt

Spacer

1.Swingtheguardwingsclosedtoalign

perpendicularwiththerearguardpanel.

g198197

Figure2

1.Guardwing—initial

position

2.Guardwing—nalposition

2.Attacheachlatch-armwith2shoulderbolts,2

spacers,and2nuts.Tightentheangenutsand

shoulderbolts.

g198332

Figure3

1.Shoulderbolt3.Spacer

2.Latch-armlink4.Flangenut

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3411-852*

Summary of content (8 pages)

PAGE 1
Form No. 3411-852 Rev C Operator Golf Ball Guard Reelmaster® 3100/3500/5010/7000, Groundsmaster® 3500/4300/4500/4700, and Machines with a Straight Roll Bar Model No. 03614 Installation Instructions Preparing the Machine Park the machine on a level surface, engage the parking brake, shut off the engine, and remove the key from the key switch (Figure 1). g198197 Figure 2 1. Guard wing—initial position g037695 Figure 1 2. 2.
PAGE 2
Installing the Ball Guard Kit 3. Make sure the two brackets are at an even height and tighten the flange nuts. Installing the Guard 4. Loosely install the ball guard to the brackets with 8 carriage bolts and 8 flange nuts. Reelmaster 3100/3500 or Groundsmaster 3500 Parts needed for this procedure: 1 Guard assembly 1 Left mounting bracket 1 Right mounting bracket 4 Strap 4 Carriage bolt—3/8 x 3-1/2 inches 12 Flange nut 8 1.
PAGE 3
Installing the Guard 4. Reelmaster 3555/3575 Loosely install the ball guard to the brackets with 8 carriage bolts and 8 flange nuts. Parts needed for this procedure: 1 Guard assembly 1 Left mounting bracket 1 Right mounting bracket 4 Strap 4 Carriage bolt—3/8 x 4-1/2 inches 12 Flange nut 8 1. Carriage bolt—3/8 x 7/8 inch Loosely mount the 2 brackets to the roll bar with 4 straps, 4 carriage bolts, and 4 flange nuts. g198626 Figure 7 1. Short carriage bolt (8) 3. Flange nut (8) 2.
PAGE 4
Installing the Guard Reelmaster 5010 or Groundsmaster 4300-D Parts needed for this procedure: 1 Guard assembly 1 Left mounting bracket 1 Right mounting bracket 4 Strap 4 Carriage bolt—3/8 x 4-1/2 inches 12 Flange nut 8 1. Carriage bolt—3/8 x 7/8 inch Loosely mount the 2 brackets to the roll bar with 4 straps, 4 carriage bolts, and 4 flange nuts. g211695 Figure 9 1. Short carriage bolt (8) 3. Flange nut (8) 2. Guard assembly 5. g211694 Figure 8 1. Right mounting bracket 4.
PAGE 5
Installing the Guard Reelmaster 7000 or Groundsmaster 4500/4700 Required Kit Parts Kit Description Toro Part No. Quantity Adapter-ball guard 137-1392 1 3. Make sure the two brackets are at an even height and tighten the flange nuts. 4. Loosely install the ball guard to the brackets with 8 carriage bolts and 8 flange nuts. Note: Do not use the hardware provided with the adapter kit.
PAGE 6
Installing the Guard Machines with a Straight Roll Bar Required Kit Parts Kit Description Toro Part No. Quantity Adapter-ball guard 137-1081 1 Parts needed for this procedure: 1 Guard assembly 1 Left mounting bracket 1 Right mounting bracket 4 Strap 4 Carriage bolt—3/8 x 3-1/2 inches 12 Flange nut 8 1. g372827 Figure 13 Carriage bolt—3/8 x 7/8 inch 1. Short carriage bolt (8) Loosely mount the 2 brackets to the roll bar with 4 straps, 4 carriage bolts, and 4 flange nuts. 5.
PAGE 7
Operation Maintenance Using the Guard Checking the Mesh Open the guard wings to access the operator platform. Close the latch to secure the guard wings in the open or closed position (Figure 14). Service Interval: Before each use or daily—Check the mesh for damage. Note: If the latch is not tight enough, tighten the nut on the latch (Figure 15). g198219 Figure 14 1. Guard wing—closed position 2. Guard wing—open position g037489 Figure 15 1. Latch 2.
PAGE 8