Installation Instructions

ManualsBrandsToro ManualsAttachmentsFinishing Kit, DPA Cutting Unit with 5in Reel, Reelmaster 5010-H Series Traction Unit

FormNo.3438-732RevA

FinishingKit

DPACuttingUnitwith5inor7inReel,Reelmaster

5010-HSeries

TractionUnit

ModelNo.03647

ModelNo.03649

InstallationInstructions

Important:Toensurethehoseroutingis

appropriateandthehosesarenottwisted,mount

themotorstothecuttingunitsbeforemounting

thenishingkits.

Usethefollowingdiagramtodeterminethe

positionsofcuttingunitsandreelmotors.

g316995

Figure1

1.Centerfrontcuttingunit4.Frontleftcuttingunit

2.Leftrearcuttingunit

5.Frontrightcuttingunit

3.Rightrearcuttingunit6.Reelmotorlocation

1.Parkthemachineonalevelsurface,engagethe

parkingbrake,shutofftheengine,andremove

thekey.

2.Onthefrontleftcorneroftheframe(#4cutting

unitlocation),removetheextraangeheadnut

ontheboltsecuringthebulkheadbrackettothe

machine(Figure2).

3.Loosenthenutonthenishingkithosetting,

insertthehoseintotheslotonthebulkhead

bracketandtightenthenut.

Note:Whentighteningthenuts,useaback

upwrenchtopreventthehosefromtwistingor

kinking.

4.Inserttheconnectorplateontothebulkhead

mountingboltswiththeconnectorspositioned

asshowninFigure2.

5.Securetheconnectorplatetooneofthe

mountingboltswiththeangenutpreviously

removed.

6.Locatethewireharnessonthemachineand

plugthewireconnectorsintothewireconnectors

ofthenishingkit.

g316962

Figure2

Leftfrontcuttingunit(#4)

1.Extraangeheadnut

3.Bulkheadbracket

2.Connectorplate

7.Repeattheprocedureontheremaining4

bulkheadlocationsasshowninFigure3thru

Figure6.

Important:Theconnectorplatesare

positioneddifferentlyattheremaining

locationssothehosecanberoutedthrough

thebulkheadbracketandtothecuttingunit

withoutgettingtwistedorkinked.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3438-732*A

Summary of content (2 pages)

PAGE 1
Form No. 3438-732 Rev A Finishing Kit DPA Cutting Unit with 5in or 7in Reel, Reelmaster® 5010-H Series Traction Unit Model No. 03647 Model No. 03649 Installation Instructions Important: To ensure the hose routing is 4. appropriate and the hoses are not twisted, mount the motors to the cutting units before mounting the finishing kits. Use the following diagram to determine the positions of cutting units and reel motors.
PAGE 2
g316994 Figure 3 Left rear cutting unit (#2) 1. Bulkhead bracket g316996 Figure 5 Right front cutting unit (#5) 3. Connector plate 2. Extra flange head nut 1. Bulkhead bracket 3. Extra flange head nut 2. Connector plate g316976 Figure 4 Center front cutting unit (#1) (Underside of machine shown) 1. Connector plate g316998 Figure 6 Right rear cutting unit (#3) 3. Bulkhead bracket 2. Extra flange head nut 1. Extra flange head nut 2. Bulkhead bracket 2 3.