Form No. 3414-302 Rev B 범용 그루머 구동 키트 Reelmaster® 46cm, 56cm, 또는 69cm Edge Series 커팅 유닛(12.7cm 또 는 17.8cm 릴 포 함 ) 모 델 번 호 03763 모 델 번 호 03764 모 델 번 호 03765 모 델 번 호 03766 모 델 번 호 03767 모 델 번 호 03768 모 델 번 호132-7115 모 델 번 호132-7125 설치 지침 경고 캘리포니아 Proposition 65 경 고 본 제품은 캘리포니아 주에서 암, 선천성 기형 및 기타 생식 기능 장애를 일으키 는 것으로 알려진 화학 물질이 들어 있습니다. 부품 확인 아래 차트를 사용하여 모든 부품이 선적되었는지 확인하십시오. 절차 1 2 3 4 5 6 © 2017—The Toro® Company 8111 Lyndale Avenue South Bloomington, MN 55420 설명 수량 사용 아무 부품도 필요 없음 – 장비를 준비합니다.
절차 7 8 9 설명 수량 왼쪽 HOC 브래킷 어셈블리 오른쪽 HOC 브래킷 어셈블리 어저스터 핀 코터 핀 바깥쪽 커버 육각 소켓, 버튼 헤드 나사(5/16 x ½ 인 치) 볼트(¼ x 1½ 인치) 잼 너트 샤프트 클램프 5 5 10 10 5 HOC 브래킷 어셈블리 및 전방 롤러를 설치합니다. 5 20 20 20 그루머 어셈블리(별도 주문)와 브루머 키트(옵션)를 설치합니다. 1 각진 피팅을 설치합니다(Reelmaster 3550 및 3555 장비의 경우 — #1 전면, 가 운데 커팅 위치 및 키트 모델 133-0150). 유압 피팅—45° (부품 번호 340–101, 별 도 구매) 1 사용 3 장비 준비 설정 판단하기 아무 부품도 필요 없음 아무 부품도 필요 없음 절차 절차 1. 평평한 곳에 장비를 주차합니다. 2. 주차 브레이크를 겁니다. 3. 엔진을 끄고 키를 뺍니다. 4. 배터리를 분리합니다. 사용 설명서 를 참조하 십시오.
중요: 커팅 유닛의 좌측에 있는 스플라인 인서 트에는 좌측 방향 나사산이 있습니다. 커팅 유닛 의 우측에 있는 스플라인 인서트에는 우측 방 향 나사산이 있습니다. 4 커팅 유닛 준비 이 절차를 수행하는 데 필요한 부품: 3 연장 스플라인 인서트(우측 방향 나사산) 2 연장 스플라인 인서트(좌측 방향 나사산) 10 플랜지 너트(⅜ 인치) 절차 g221766 그림3 그림은 커팅 유닛의 오른쪽 참고: 달리 명시되지 않는 한 분리한 모든 부품은 폐 기할 수 있습니다. 1. 2. 트랙션 유닛에서 모든 커팅 유닛을 분리합니다. 1. 연장 스플라인 인서트 (115~128N∙m의 토크로 조입니다.) 사용 설명서 를 참조하십시오. 2. 예고(HOC) 브래킷을 커팅 유닛 측면 플레이트 에 고정하는 캐리지 볼트와 록너트를 뺍니다 (그림2). 중간 강도의 제거 가능한 나사산 고정 컴파운드를 나사산 에 바릅니다 6.
5 웨이트 브래킷 및 그루머 구 동함 설치 이 절차를 수행하는 데 필요한 부품: 5 웨이트 브래킷 10 육각 소켓, 버튼 헤드 볼트(⅜ x ¾ 인치) 3 그루머 구동함 (좌측 구동) 2 그루머 구동함 (우측 구동) g037065 그림5 1. 플랜지 헤드 볼트 2. 플랜지 록너트(⅜ 인치) 절차 1. 좌측 구동 그루머 구동함과 우측 구동 그루머 구 동함을 구분하십시오. 그림6를 참조하십시오. g037105 그림6 1. 우측(노란색) 어댑터 2. 좌측(녹색) 어댑터 2. 그루머 구동함 — 우측 구 동 4. 그루머 구동함 — 좌측 구 동 3. 그림7에 나오는 것처럼 2개의 육각 소켓 버튼 헤 드 볼트(⅜ x ¾ 인치)를 사용하여 웨이트 브래 킷을 릴에 고정합니다. 참고: 릴에서 그루머 구동함을 장착하려는 쪽에 웨이트 브래킷을 부착합니다.
6 아이들러 어셈블리 설치 이 절차를 수행하는 데 필요한 부품: g227902 그림7 1. 2. 웨이트 브래킷 육각 소켓, 버튼 헤드 볼 트—⅜ x ¾ 인치 (2) 3. 그루머 구동함 (그림의 좌 측 구동) 4. 5. 나사산 고정 컴파운드 육각 헤드(135~150N∙m의 토크로 조입니다) 3. 중간 강도 나사산 고정 컴파운드(예: Blue Loctite® 243)를 내부 릴 샤프트(그림7)의 나사 산에 바릅니다. 4. 그루머 구동함의 육각 헤드를 사용하여 그루머 구동함을 릴 샤프트(그림7)에 부착합니다. 10 육각 소켓 볼트 5 피봇 허브 5 O-링 2 아이들러 어셈블리(좌측) 3 아이들러 어셈블리(우측) 10 록너트(⅜ 인치) 절차 1. 그루머 구동함에서 릴의 반대쪽에 아이들러 어 셈블리를 배치합니다. 2. O-링 및 피봇 허브 어셈블리에 장착합니다. 3. 피봇-허브 어셈블리의 바깥쪽 직경에 고착 방지 제를 바릅니다(그림8).
7 HOC 브래킷 어셈블리 및 전 방 롤러 설치 이 절차를 수행하는 데 필요한 부품: 5 왼쪽 HOC 브래킷 어셈블리 5 오른쪽 HOC 브래킷 어셈블리 10 어저스터 핀 10 코터 핀 5 바깥쪽 커버 5 육각 소켓, 버튼 헤드 나사(5/16 x ½ 인치) g232400 그 림 10 1. 2. 3. 절차 1. 앞에서 빼 둔 캐리지 볼트와 록너트를 사용하여 왼쪽과 오른쪽 HOC 브래킷 어셈블리와 전방 롤 러 어셈블리를 커팅 유닛 측면 플레이트에 느슨 하게 설치합니다(그림9). 어저스터 핀 어저스터 암 로드 3. 4. 코터 핀 그루머 구동함 아이들러 어셈블리 쪽에서, HOC 브래킷의 어 저스터 암 로드를 아이들러 어셈블리의 어저스 터 칼라에 맞추어 정렬하고 어저스터 핀 및 코 터 핀으로 고정합니다(그림11). g232389 그림9 오른쪽 HOC 브래킷 어셈 블리 2. 전면 롤러 어셈블리 3. 왼쪽 HOC 브래킷 어셈블 리 1. 2. 4. 와셔 5.
8 그루머 어셈블리와 브루머 키 옵션 ) 설 치 트 (옵 그루머와 브루머 키트는 별도로 제 공됨 이 절차를 수행하는 데 필요한 부품: 그 림 12 조정 볼트 록너트 캐리지 볼트 및 록너트 4. 5. 볼트(¼ x 1½ 인치) 20 잼 너트 20 샤프트 클램프 브루머 키트 설치 g192299 1. 2. 3. 20 별도 주문 캡나사 플랜지 너트 모델 번호 그루머 키트 03764 46cm 그루머 블레이드 카트리지 키트 03765 56cm 그루머 블레이드 카트리지 키트 5. HOC 어저스터 볼트에 대고 록너트를 조인 다 음, 록너트를 1/2 바퀴 풉니다(그림12). 03241 69cm 그루머 블레이드 카트리지 키트 03766 6. 전면 롤러의 중심을 HOC 브래킷 어셈블리 사 이에 맞추고 캡 나사와 플랜지 너트로 제자리에 고정합니다(그림12).
g035827 그 림 14 1. 구동 스터브 샤프트 4. 샤프트 클램프(4) 2. 그루머 어셈블리 5. 볼트 (4) 5~7N∙m의 토크로 조입니다. 3. 3. 4. g032403 그 림 15 잼 너트(4) 1. 2. 4개의 볼트(¼ x 1½ 인치), 4개의 잼 너트 및 4개 의 샤프트 클램프를 사용하여 그림14에 나오는 것처럼 그루머를 장비에 고정합니다. 3. 볼트를 5~7 N∙m의 토크로 조입니다. 스트랩 버클 리테이닝 너트 3. 4. 스트랩 브러시 그루머 릴의 한쪽 측면에서, 그루머 릴의 전체 길이를 따라가며 브러시를 각 홈의 안쪽으로 밀 어 넣습니다(그림16). 브루머 키트 설치 부품 번호 브루머 키트 132-7115 46cm 브루머 키트 132-7125 56cm 브루머 키트 133-8222 69cm 브루머 키트 1. 자신에게 필요한 점 및 커팅 유닛에 적합한 그루 머 블레이드 카트리지 키트용 브루머 키트(옵션) 를 구하십시오.
각진 피팅 설치 Reelmaster 3550 및 3555 장비의 경 우 — #1 전면, 가운데 커팅 위치 및 키 만 해당됨 트 모델 133-0150만 g032402 그 림 17 1. 5. 브러시 2. 블레이드 이 절차를 수행하는 데 필요한 부품: 절차 다음 표를 사용하여 브러시에 스트랩을 배치 합니다: 릴 크기 스트랩 간격 46cm 블레이드 2와 3, 11와 12, 21과 22 및 30과 31 사이에 스트랩 을 배치합니다 56cm 블레이드 2와 3, 14와 15, 26과 27 및 38과 39 사이에 스트랩 을 배치합니다 96cm 블레이드 2와 3, 23과 24, 24 와 25 및 35과 36, 45와 46 사 이에 스트랩을 배치합니다 중요: Reelmaster 3550 및 3555 장비의 경우—#1 전 만 해당 면, 가운데 커팅 위치 및 키트 모델 133-0150만 부품 번호 340–101)을 을 주문하고 아 됨; 45° 유압 피팅(부 래 절차를 따릅니다.
운영 서론 그루밍은 지면 위의 잔디 윗 부분을 다듬는 것입니다. 그루밍을 하면 잔디의 수직 성장이 촉진되고 알갱이 가 줄어들며 줄기를 잘라내므로 잔디가 더욱 조밀해 지며, 골프공이 좀더 빠르고 정확하게 움직이는, 보다 균일하고 조밀한 경기면이 만들어집니다. 그루밍을 수직 커팅을 대체하는 것으로 보아서는 안됩 니다. 수직 커팅은 일반적으로 경기장 표면을 일시적 으로 손상시킬 수 있는 처리 방법으로 주기적으로 보 다 엄격하게 실시되지만, 그루밍은 잔디를 다듬도록 고안된 일상적이고 비교적 부드러운 처리 방법입니다. g006671 그 림 19 1. g190850 5. 커팅 유닛 모터 각진 유압 피팅 3. 2. 대취 그루밍 브러시는 잔디 윗부분에 살짝 닿도록 조정을 하면 기존의 그루밍 블레이드에 비해 잔디를 덜 손 상시킵니다. 키가 매우 낮은 품종의 경우 브러시를 사용하는 것이 더 좋을 것입니다.
• 전반적인 관리 프로그램(즉, 관수, 비료 주기, 분 무, 코어링, 흩어 뿌리기 등등) • 통행량 • 스트레스를 받는 시기(즉, 고온, 다습, 예외적으로 많은 통행량) 그루머 높이 조정 이런 요인들은 페어웨이마다 차이가 있습니다. 예초 영역을 자주 검사하고 필요에 따라 그루밍 방식에 변 화를 주십시오. 참고: 그루머 릴을 부적절하게 사용하거나 지나치 게 공격적으로 사용하면(즉, 너무 깊게 또는 너무 자 주 그루밍하면) 잔디가 불필요하게 스트레스를 받 아 심하게 손상될 수 있습니다. 그루머를 주의하여 사용하십시오. 1. 장비를 깨끗하고 평평한 곳에 주차하고 커팅 유 닛을 지면까지 완전히 내리고 엔진을 멈춘 후 주 차 브레이크를 걸고 키를 뺍니다. 2. 롤러에 이물질이 없고 커팅 유닛이 원하는 예고 로 설정되어 있는지 확인합니다(커팅 유닛 사 용 설명서 참조). 3. 퀵업 레버(그림20)를 ENGAGED(체결) 위치(핸 들이 커팅 유닛의 전방을 향하는 위치)까지 돌 립니다.
예 고 (HOC) 및 그 루 밍 높 이 (HOG) 권 장 범 위 예 고 (mm) 인치 ) 예 고 (인 후방 롤러 스 페이서의 수 권장 HOG = HOC - 그루머 체결 위치 권장 HOG = HOC - 그루머 체결 위치 (mm) (인치) 6.3 0.250 0 3.1~6.3 0.125~0.250 9.5 0.375 0 4.7 - 9.5 0.187 - 0.375 9.5 0.375 1 4.7 - 9.5 0.187 - 0.375 12.7 0.500 0 6.3 - 12.7 0.250 - 0.500 12.7 0.500 1 6.3 - 12.7 0.250 - 0.500 12.7 0.500 2 6.3 - 9.5 0.250 - 0.375 15.8 0.625 0 9.5 - 15.8 0.375 - 0.625 15.8 0.625 1 9.5 - 15.8 0.375 - 0.625 15.8 0.625 2 9.5 - 12.7 0.375 - 0.
그루머 성능 시험 유지보수 중요: 그루밍 릴을 부적절하게 사용하거나 지나치게 즉, 너무 깊게 또는 너무 자주 그 공격적으로 사용하면(즉 루밍하면) 잔디가 불필요하게 스트레스를 받아 심하게 손상될 수 있습니다. 그루머를 주의하여 사용하십시오. 기어박스 윤활유 교환 서비스 간격: 매 500시간/매년 (먼저 해당하는 쪽으 로 적용) 위험 1. 그루머 하우징 외부 표면을 청소하십시오. 2. 하우징 하단의 드레인 플러그를 뺍니다(그림22). 3. 하우징 측면의 레벨 플러그를 분리하여 오일을 배출하기 쉽도록 환기구를 만듭니다(그림22). 4. 배출 포트가 제일 밑이 될 때까지 커팅 유닛을 뒤로 기울여 완전히 배출되게 합니다. 5. 오일이 완전히 배출되면, 커팅 유닛을 평평한 곳 에 놓습니다. 정상적으로 사용하기 전에 반드시 그루머의 성능을 확인해야 합니다. 6. 드레인 플러그를 장착한다. 7. 하우징 상단의 주입 플러그를 뺍니다(그림22).
그루밍 릴 청소 서 비 스 간 격 : 매번 사용 후 그루밍 릴은 사용한 후 물을 분무하여 청소하십시오. 그루머 베어링 씰을 향해 물줄기를 겨냥하지 마십시 오. 그루밍 릴이 물에 잠기지 않게 하십시오. 그렇게 하면 부품에 녹이 생깁니다. 블레이드 점검 서비스 간격: 매번 사용하기 전 또는 매일 그루밍 릴 블레이드를 자주 점검하여 손상과 마모를 확인합니다. 휘어진 블레이드는 플라이어를 사용하여 똑바로 펴고 마모된 블레이드는 교체합니다. 블레이 드를 점검할 때, 우측과 좌측 블레이드 샤프트 엔드 너 트가 단단히 조여 있는지 확인합니다. g010613 그 림 23 1. 2. 그루밍 블레이드 무딘(둥근) 날 3.
편 입 선 언 서 (DI) The Toro Company(8111 Lyndale Ave. South, Bloomington, MN, USA)는 다음 장치(들)이 관련 적합성 선언 문(Declarations of Conformity)에 명시된 대로 특정 Toro 모델에 동봉된 지침에 따라 설치되면 명시된 지침 에 일치함을 밝힙니다. 모델 번호 일련번호 03763 — 03768 — 제품 설명 범용 그루머 구동 키트, Reelmaster 3550, 3555, 5010 및 5010-H 시리즈 46cm 및 56cm 커팅 유닛 (12.7cm 릴 포함) 범용 그루머 구동 키트, Reelmaster 3575, 5010, 5010-H 및 7000 시리즈 56cm 또는 69cm 커팅 유 닛(17.