Form No. 3414-295 Rev B Universal Groomer Drive Kit Reelmaster® 18-inch, 22-inch, or 27-inch Edge Series Cutting Units with 5-inch or 7-inch Reel Model No. 03763 Model No. 03764 Model No. 03765 Model No. 03766 Model No. 03767 Model No. 03768 Model No. 132-7115 Model No. 132-7125 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
Procedure 7 8 9 Description Qty. Left HOC bracket assembly Right HOC bracket assembly Adjuster pin Cotter pin Outer cover Hex-socket, button-head screw (5/16 x 1/2 inch) Bolt (1/4 x 1-1/2 inches) Jam nut Shaft clamp 5 5 10 10 5 Hydraulic fitting—45° (Part No. 340–101; sold separately) 1 Use Install the HOC bracket assemblies and the front roller. 5 20 20 20 Install the groomer assembly (ordered separately) and optional broomer kit.
Important: The splined insert on the left 4 side of the cutting unit has left-hand threads. The splined insert on the right side of the cutting unit has right-hand threads. Preparing the Cutting Unit Parts needed for this procedure: 3 Extended splined insert (right-hand threads) 2 Extended splined insert (left-hand threads) 10 Flange locknut (3/8 inch) Procedure g221766 Figure 3 Right side of cutting unit shown Note: You may discard all removed parts unless otherwise stated. 1.
B. Install the 2 existing flange-head bolts from the inside of the cutting unit, and secure them with the 3/8 inch flange locknuts (Figure 5). 5 Installing the Weight Bracket and the Groomer Drive Box Parts needed for this procedure: g037065 Weight bracket 10 Hex-socket, button-head bolt (3/8 x 3/4 inch) 3 Groomer drive box (left drive) 2 Groomer drive box (right drive) Procedure Figure 5 1. Flange-head bolts 5 1. 2.
6 Installing the Idler Assembly Parts needed for this procedure: 10 Hex-socket bolt 5 Pivot hub 5 O-ring 2 Idler assembly (left) 3 Idler assembly (right) 10 Locknut (3/8 inch) g227902 Figure 7 1. Weight bracket 4. Thread-locking compound 2. Hex-socket, button-head bolt—3/8 x 3/4 inch (2) 5. Hex-head (Torque to 135 to 150 N∙m (100 to 110 ft-lb)) Procedure 3. Groomer drive box (left drive shown) 3.
7 Installing the HOC Bracket Assemblies and the Front Roller Parts needed for this procedure: 5 Left HOC bracket assembly 5 Right HOC bracket assembly 10 Adjuster pin 1. Adjuster pin 3. Cotter pin 10 Cotter pin 2. Adjuster-arm rod 4. Groomer drive box 5 Outer cover 5 Hex-socket, button-head screw (5/16 x 1/2 inch) g232400 Figure 10 3. Procedure 1.
8 Installing the Groomer Assembly and Optional Broomer Kit Groomer and Broomer Kits Come Separately Parts needed for this procedure: 20 Bolt (1/4 x 1-1/2 inches) 20 Jam nut 20 Shaft clamp g192299 Figure 12 1. Adjusting bolt 4. Capscrew 2. Locknut 5. Flange nut Installing the Groomer Kit Ordered Separately 3. Carriage bolt and locknut Model Number 5. Tighten the locknut on the HOC adjuster bolt, then back off the locknut 1/2 turn (Figure 12). 6.
g035827 Figure 14 1. Drive-stub shaft 4. Shaft clamp (4) 2. Groomer assembly 5. Bolt (4) Torque to 5 to 7 N∙m (46 to 60 in-lb) g032403 Figure 15 3. Jam nut (4) 3. 4. Secure the groomer to the machine as shown in Figure 14 using 4 bolts (1/4 x 1-1/2 inches), 4 jam nuts, and 4 shaft clamps. 1. Strap buckle 3. Strap 2. Retaining nut 4. Brush 3. Torque the bolts to 5 to 7 N∙m (46 to 60 in-lb).
Installing the Angled Fitting For Reelmaster 3550 and 3555 Machines—#1 Front, Center Cutting Location and Kit Model 133-0150 Only g032402 Figure 17 1. Brush 5. 2. Blade Parts needed for this procedure: Loosely wrap the straps, as shown in Figure 15, around the groomer reel shaft and brushes inserting the straps in the grooves in the brushes Figure 17.
Operation Introduction Grooming is performed in the turf canopy above the soil level. Grooming promotes vertical growth of grass plants, reduces grain, and severs stolons, producing a denser turf. Grooming produces a more uniform and tighter playing surface for faster and truer action of the golf ball. Grooming should not be considered as a replacement for verticutting.
Adjusting the Groomer Height • The overall management program (i.e., irrigation, fertilizing, spraying, coring, overseeding, etc.) • Traffic • Stress periods (i.e., high temperatures, high 1. Park the machine on a clean and level surface, lower the cutting units completely to the ground, shut off the engine, engage the parking brake, and remove the key. 2. Make sure that the rollers are clean and the cutting unit is set to the desired height-of-cut (see your cutting unit Operator’s Manual). 3.
Height-of-Cut (HOC) and Height-of-Groom (HOG) Recommended Range Height-of-Cut (mm) Height-of-Cut (inch) Number of Rear Roller Spacers Recommended HOG = HOC Groomer Engagement Recommended HOG = HOC Groomer Engagement (mm) (inch) 6.3 0.250 0 3.1 to 6.3 0.125 to 0.250 9.5 0.375 0 4.7 to 9.5 0.187 to 0.375 9.5 0.375 1 4.7 to 9.5 0.187 to 0.375 12.7 0.500 0 6.3 to 12.7 0.250 to 0.500 12.7 0.500 1 6.3 to 12.7 0.250 to 0.500 12.7 0.500 2 6.3 to 9.5 0.250 to 0.375 15.8 0.
Maintenance Testing the Groomer Performance Changing the Gearbox Lubricant Important: Improper or over-aggressive use of the grooming reel (i.e., too deep or too frequent grooming) may cause unnecessary stress on the turf, leading to severe damage. Use the groomer cautiously. Service Interval: Every 500 hours/Yearly (whichever comes first) 1. Clean the external surfaces of the groomer housing. Contact with the reels or other moving parts can result in personal injury. 2.
Cleaning the Grooming Reel Service Interval: After each use Clean off the grooming reel after using it by spraying it with water. Do not direct the water stream directly at the groomer bearing seals. Do not permit the grooming reel to stand in water so that the components rust. Inspecting the Blades Service Interval: Before each use or daily Inspect the grooming-reel blades frequently for damage and wear. Straighten bent blades with a pliers and replace worn blades.
Declaration of Incorporation The Toro Company, 8111 Lyndale Ave. South, Bloomington, MN, USA declares that the following unit(s) conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain Toro models as indicated on the relevant Declarations of Conformity. Model No. Serial No.
