Form No. 3386-664 Rev B Reelmaster® 7000-D 4-Wheel Drive Traction Unit Model No. 03780—Serial No. 315000001 and Up Model No. 03780A—Serial No. 315000001 and Up Register at www.Toro.com.
This product complies with all relevant European directives, for details please see the separate product specific Declaration of Conformity (DOC) sheet. Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely. WARNING You may contact Toro directly at www.Toro.com for product and accessory information, help finding a dealer, or to register your product.
Contents Servicing the Diesel-Oxidation Catalyst (DOC) and the Soot Filter .............................. 54 Fuel System Maintenance ................................... 55 Fuel Tank.......................................................... 55 Fuel Lines and Connections ............................. 55 Servicing the Water Separator ......................... 55 Servicing the Fuel Filter .................................... 56 Fuel Pick up Tube Screen .................................
Preparation Safety • While mowing, always wear substantial footwear, This machine meets or exceeds EN ISO 5395:2013 (when appropriate decals applied), and ANSI B71.4-2012 specifications in effect at the time of production. long trousers, hard hat, safety glasses, and ear protection. Long hair, loose clothing, or jewelry may get tangled in moving parts. Do not operate the equipment when barefoot or wearing open sandals. Improper use or maintenance by the operator or owner can result in injury.
Operation • Do not operate the engine in a confined space • • • • • • • • • • • • where dangerous carbon monoxide fumes can collect. Mow only in daylight or in good artificial light. Before attempting to start the engine, disengage all blade attachment clutches, shift into neutral, and engage the parking brake. Remember there is no such thing as a safe slope. Travel on grass slopes requires particular care.
• Wearing safety shoes and long pants is advisable • Clean grass and debris from cutting units, drives, • • • • • • silencers/mufflers, and engine to help prevent fires. Clean up oil or fuel spillage. Use jack stands to support components when required. Carefully release pressure from components with stored energy. Disconnect battery before making any repairs. Disconnect the negative terminal first and the positive last. Reconnect positive first and negative last.
Vibration Level high pressure. Use paper or cardboard, not your hands, to search for leaks. Hydraulic fluid escaping under pressure can have sufficient force to penetrate the skin and cause serious injury. Seek immediate medical attention if fluid is injected into skin. Hand-Arm Measured vibration level for right hand =0.3 m/s2 Measured vibration level for left hand =0.3 m/s2 • Before disconnecting or performing any work on Uncertainty Value (K) = 0.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. decal117-4765 117-4765 1. Read the Operator's Manual. 2. Do not use starting aids. decal117-4763 117-4763 2. To disengage the parking 1. To engage the parking brake, disengage the brake, secure the brake locking pin and release the pedals with the locking pin, pedals.
decal98-4387 98-4387 1. Warning—wear hearing protection. decal93-6688 93-6688 1. Warning—read the instructions before servicing or performing maintenance. 2. Cutting hazard of hand or foot—stop the engine and wait for moving parts to stop. decal125-8754 125–8754 decal110-9642 110-9642 1. Stored energy hazard—read the Operator's Manual. 2. Move the cotter pin to the hole closest to the rod bracket and then remove the lift arm and pivot yoke. 1. Head lights 6. Slow 2. Engage 7.
decal121-3884 121–3884 1. Engine—stop 3. Engine—start 2. Engine—preheat decal125-4605 125–4605 decal112-5019 112-5019 1. Power seat, 10A 6. Power supplied, 10A 2. 7. Controller, 2A Work light, 10A 3. Engine, 10A 8. Power supplied, 7.5A 4. Cigarette lighter, 10A 9. Controller, 2A 5. Infocenter, 2A 10. Engine preheat, 60A decal93-6681 93–6681 1. Cutting/dismemberment hazard—stay away from moving parts. decal120-1670 120-1670 1. Traction unit speed decal106-6754 106-6754 2. Slow 1.
decalbatterysymbols Battery Symbols Some or all of these symbols are on your battery 1. Explosion hazard 6. Keep bystanders a safe distance from the battery. 2. No fire, open flame, or smoking. 7. Wear eye protection; explosive gases can cause blindness and other injuries 3. Caustic liquid/chemical burn hazard 4. Wear eye protection 8. Battery acid can cause blindness or severe burns. 9. Flush eyes immediately with water and get medical help fast. 5. Read the Operator's Manual.
decal120-1683 120-1683 1. Warning—read the Operator's Manual, do not operate this machine unless you are trained. 4. Warning—do not park the machine on slopes; engage the parking brake, lower the cutting units, stop the engine and remove the ignition key before leaving the machine. 2. Warning—read the Operator's Manual before towing the machine. 3.
decal120-1686 120-1686 Affix over part no. 120–1683 for CE* *This safety decal includes a slope warning required on the machine fro compliance to the European Lawn Mower Standard EN ISO 5395:2013. The conservative maximum slope angles indicated for operation of this machine are prescribed by and required by this standard. 1. Warning—read the Operator's Manual, do not operate this machine unless you are trained. 4.
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description 1 2 3 4 5 6 7 8 9 Use Qty. No parts required – Adjust the support rollers Warning decal 1 Used only on machines requiring CE Compliance. Hood lock bracket Rivet Screw, 1/4 x 2 inch Flat washer, 1/4 inch Locknut, 1/4 inch Front hose guide-R.H. Front hose guide-L.H. 1 2 1 2 1 1 1 No parts required – Adjust the turf compensation spring.
1 2 Adjusting the Support Rollers Replacing the Warning Decal for CE Compliance No Parts Required Parts needed for this procedure: 1 Warning decal Procedure Depending on what width cutting units are to be installed on the traction, adjust the support rollers as follows: Procedure On machines requiring CE Compliance, affix the warning decal, part no. 120–1683 over the warning decal part no. 120–1686.
g012629 Figure 6 1. CE lock bracket 2. Bolt and nut assembly g014982 Figure 4 4. Align the washers with the holes on the inside of the hood. 5. Rivet the brackets and the washers to the hood (Figure 6). 6. Hook the latch onto the hood latch bracket (Figure 7). 1. Hood latch 2. Remove the (2) rivets securing the hood latch bracket to the hood (Figure 5). Remove the hood latch bracket from the hood. g012630 Figure 7 1. Hood latch g012628 Figure 5 1. Hood latch bracket 3. 2. Rivets 7.
g012631 Figure 8 1. Bolt 2. Nut 3. Arm of hood lock bracket 4 g003320 Figure 9 1. Counter weight Installing the Cutting Units 5. Parts needed for this procedure: 1 Front hose guide-R.H. 1 Front hose guide-L.H. All the cutting units are shipped with the turf compensation spring mounted to the right side of the cutting unit. The turf compensation spring must be mounted to the same side of the cutting unit as the reel drive motor. Reposition the turf compensation as follows: A. Procedure 1.
g003967 Figure 11 1. Opposite carrier frame tab D. 2. Rod bracket Mount the rod bracket to the cutting unit tabs with the carriage bolts and nuts (Figure 11). Also, on the cutting unit, mount the left hand hose guide to the front of the cutting unit tabs when reinstalling the rod bracket (Figure 13). Important: On the #4 (left front) and g015160 #5 (right front) cutting units, use the rod bracket mounting nuts to install the hose guides to the front of the cutting unit tabs.
9. For the front cutting units, slide a cutting unit under the lift arm while inserting the carrier frame shaft up into the lift arm pivot yoke (Figure 16). Make sure the thrust washer is in position on the carrier frame shaft. 10. Secure the carrier frame shaft to the lift arm yoke with the Klik pin (Figure 16). 11. To lock (fix) the steering on the cutting units, secure the pivot yoke to the carrier frame with the snapper pin (Figure 17). g015978 Figure 15 1. Hex socket screw 2. Pivot spacer 3.
number of chain links described in the cutting unit Operator's Manual. 5 Adjusting the Turf Compensation Spring No Parts Required Procedure g003948 Figure 19 1. Lift arm chain The turf compensation spring (Figure 21) transfers weight from the front to the rear roller. (This helps to reduce a wave pattern in the turf, also known as marcelling or bobbing.) 3. Snapper pin 2. Chain bracket 14. Coat the spline shaft of the reel motor with clean grease. 15.
6 Using the Cutting Unit Kickstand Parts needed for this procedure: 1 Cutting unit kickstand Procedure Whenever the cutting unit has to be tipped to expose the bedknife/reel, prop up the rear of the cutting unit with the kickstand to make sure the nuts on the back end of the bedbar adjusting screws are not resting on the work surface (Figure 22). g004144 Figure 23 1. Chain bracket 3. Cutting unit kickstand 2.
8 Checking Fluid Levels No Parts Required Procedure 1. Check the rear axle lubricant level before the engine is first started, refer to Checking the Rear Axle Lubricant in Drive System Maintenance. 2. Check the hydraulic fluid level before the engine is first started, refer to Checking the Hydraulic Fluid Level in Operation. 3. g004552 Figure 24 1. Gauge bar Check the engine oil level before and after the engine is first started, refer to Checking the Engine Oil Level in Operation. 2.
Tilt Steering Pedal Product Overview To tilt the steering wheel towards you, press the foot pedal (Figure 25) down, and pull the steering tower toward you to the most comfortable position and then release the pedal. Controls Brake Pedals Mow Speed Limiter Two foot pedals (Figure 25) operate individual wheel brakes for turning assistance and to aid in obtaining better side hill traction. The pedal locking latch (Figure 25) connects the pedals together to engage the parking brake.
InfoCenter The InfoCenter LCD display shows information about your machine such as the operating status, various diagnostics and other information about the machine (Figure 27). PTO Switch The PTO switch (Figure 27) has two positions: Out (start) and In (stop). Pull the PTO button out to engage the cutting unit blades. Push in the button to disengage the cutting unit blades. g010239 Figure 28 1. Power point 2. Bag holder Bag Holder Use the bag holder (Figure 28) for storage. g021208 Figure 27 1.
Seat Adjustments Using the InfoCenter LCD Display The InfoCenter LCD display shows information about your machine such as the operating status, various diagnostics, and other information about the machine (Figure 31) There is a splash screen and main information screen of the InfoCenter. You can switch between the splash screen and main information screen, at any time, by pressing any of the InfoCenter buttons and then selecting the appropriate directional arrow.
InfoCenter Icon Description SERVICE DUE InfoCenter Icon Description (cont'd.
InfoCenter Icon Description (cont'd.) Hours Lists the total number of hours that the machine, engine and PTO have been on, as well as the number of hours the machine has been transported and service due. Counts Lists numerous counts the machine has experienced. Engine coolant too hot Hydraulic fluid too hot Diagnostics DPF ash accumulation notification. Refer to Servicing the Diesel-Oxidation Catalyst (DOC) and the Soot Filter (page 54) in the maintenance section for details.
F Reel RPM Displays the calculated reel speed position for the front reels. The reels can also be manually adjusted. R Reel RPM Displays the calculated reel speed position for the rear reels. The reels can also be manually adjusted. * Only "operator-faced" text is translated. Faults, Service, and Diagnostics screens are "service-faced". Titles will be in the selected language, but menu items are in English. g028523 Figure 32 About 2.
To Set the Front and Rear Reel Speeds Note: Rotate the key switch to the OFF position and then to the ON position locks the protected menu. You have the ability to view and change the settings in the Protected Menu. Once you access the Protected Menu, scroll down to Protect Settings option. Use the right button to change the setting. Setting the Protect Settings to OFF allows you to view and change the settings in the Protected Menu without entering the PIN code.
Operation Note: Determine the left and right sides of the machine from the normal operating position. CAUTION This machine produces sound levels in excess of 85 dBA at the operator's ear and can cause hearing loss through extended periods of exposure. Wear hearing protection when operating this machine. CAUTION If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure you or other bystanders. g009702 Figure 34 1.
Filling the Fuel Tank WARNING Fuel is harmful or fatal if swallowed. Long-term exposure to vapors can cause serious injury and illness. • Avoid prolonged breathing of vapors. • Keep your face away from the nozzle and fuel tank opening. • Keep fuel away from your eyes and skin. DANGER In certain conditions, fuel is extremely flammable and highly explosive. A fire or explosion from fuel can burn you and others and can damage property. • Fill the fuel tanks outdoors, in an open area, when the engine is cold.
Using summer-grade fuel above -7°C (20°F) contributes toward longer fuel pump life and increased power compared to winter-grade fuel. Biodiesel This machine can also use a biodiesel blended fuel of up to B20 (20% biodiesel, 80% petroleum diesel). Sulfur content: Ultra-low sulfur (<15 ppm) Biodiesel fuel specification: ASTM D6751 or EN14214 Blended fuel specification: ASTM D975, EN590, or JIS K2204 Important: The petroleum diesel portion must be ultra-low sulfur.
Viscosity, ASTM D445 Viscosity index, ASTM D2270 Pour point, ASTM D97 cSt @ 40°C (104°F) 44 to 50 cSt @ 100°C (212°F) 7.9 to 9.
Starting and Stopping the Engine Starting the Engine 4. Rotate the ignition key to Off. 5. Remove the key from the switch to prevent accidental starting. Engine Speed Switch Important: The fuel system must be bled if any of the following situations have occurred: • The engine has ceased running due to lack of fuel. • Maintenance has been performed upon the fuel system components. 1. Remove your foot from the traction pedal and ensure that it is in neutral. Ensure that the parking brake is set. 2.
4. Diesel Particulate Filter Regeneration Sit on the seat, engage the parking brake and start the engine. Move the traction pedal out of the neutral position. The engine should kill. If the engine does not kill, there is a malfunction in the interlock system that should be corrected before beginning operation. The diesel particulate filter (DPF) is part of the exhaust system. The diesel-oxidation catalyst of the DPF reduces harmful gasses and the soot filter removes soot from the engine exhaust.
DPF Soot Accumulation • DPF regeneration is a process that heats the DPF to convert the soot to ash. • Over time, the DPF accumulates soot in the soot • In addition to the warning messages, the computer filter. The computer for the engine monitors the soot level in the DPF. reduces the power produced by the engine at different soot-accumulation levels. • When enough soot accumulates, the computer informs you that it is time to regenerate the diesel particulate filter.
DPF Ash Accumulation • When enough ash accumulates, the engine • The lighter ash is discharged through the exhaust system; the heavier ash collects in the soot filter. • Ash is a residue of the regeneration process. Over • time, the diesel particulate filter accumulates ash that does not discharge with the engine exhaust. • • The computer for the engine calculates the amount of ash accumulated in the DPF.
Types of Diesel Particulate Filter Regeneration Types of diesel particulate filter regeneration that are performed while the machine is operating: Type of Regeneration Conditions for DPF regeneration DPF description of operation Passive Occurs during normal operation of the machine at high-engine speed or high-engine load The InfoCenter does not display an icon indicating passive regeneration.
Types of diesel particulate filter regeneration that require you to park the machine: (cont'd.) Type of Regeneration Conditions for DPF regeneration DPF description of operation Recovery Occurs as a result of ignoring parked regeneration requests and continuing operation, adding more soot when the DPF is already in need of a parked regeneration When the recovery-regeneration icon is displayed in the InfoCenter, a recovery regeneration is requested.
Parked Regeneration Reset Regeneration g214713 g214711 Figure 44 Assist/reset-regeneration icon Figure 45 Parked-regeneration request icon • The assist/reset-regeneration icon displays in the • The parked-regeneration requested icon displays in the InfoCenter (Figure 45). If a parked regeneration is needed, the InfoCenter displays engine warning SPN 3719, FMI 16 (Figure 46) and the engine computer derates engine power to 85%. InfoCenter (Figure 44).
6. Engage the parking brake. 7. Set the throttle to the low IDLE position. Performing a Parked Regeneration Note: For instructions on unlocking protected menus, refer to Accessing Protected Menus (page 28). 1. Access the protected menu and unlock the protected settings submenu (Figure 47); refer to Accessing Protected Menus (page 28). g212138 Figure 49 4. When the “Initiate DPF Regen. Are you sure?” message displays, press the center button (Figure 50). g028523 Figure 47 2.
g211986 g212405 Figure 51 6. Figure 53 Move the throttle control to LOW IDLE and press the center button (Figure 52). B. The “Waiting on (Figure 54). ” message displays g212372 g212406 Figure 52 7. Figure 54 The following messages display as the parked regeneration process begins: A. C. The “Initiating DPF Regen.” message displays (Figure 53). The computer determines whether the regeneration runs.
The engine is cold—wait. The engine is warm—wait. The engine hot—regeneration in progress (percent complete). 9. g213424 The parked regeneration is complete when the “Regen Complete” message displays in the InfoCenter. Press the left button to exit to the home screen (Figure 57). Figure 55 • If the regeneration process is not allowed by the engine computer, the “DPF Regen Not Allowed” message displays in the InfoCenter (Figure 56).
• Perform a recovery-regeneration whenever there is a loss of engine power and a parked regeneration cannot effectively clean the DPF of soot. • A recovery regeneration requires up to 4 hours to complete. • You need a distributor technician to perform the recovery regeneration process; contact your Authorized Toro Distributor.
3. Jacking Points Loosen the switch mounting screws (Figure 60) and move the switch up to increase the lift arm turn around height or move the switch down to decrease the lift arm turn around height. Tighten the mounting screws.
shutting the engine off. Failure to do so may lead to turbo-charger trouble. Before stopping the engine, disengage all controls and move the throttle to Slow. Moving the throttle to Slow reduces high engine RPM, noise, and vibration. Turn the key to Off to stop the engine. Operating Tips Familiarization Before mowing grass, practice operating the machine in an open area. Start and stop the engine. Operate in forward and reverse. Lower and raise the cutting units and engage and disengage the reels.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 8 hours • Torque the wheel nuts. After the first 200 hours Before each use or daily • Change the planetary gear drive oil. • Change the rear axle lubricant. • Change the hydraulic filters. • • • • • • • • • Check the cooling system. Check the level of the hydraulic fluid. Check the tire pressure.
Daily Maintenance Checklist Duplicate this page for routine use. Maintenance Check Item For the week of: Mon. Tues. Wed. Thurs. Fri. Sat.
Service Interval Chart decal130-1651 Figure 62 CAUTION If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure you or other bystanders. Remove the key from the ignition before you do any maintenance.
Pre-Maintenance Procedures Lubrication Greasing the Bearings and Bushings Removing the Hood 1. Service Interval: Every 50 hours Release hood latches (Figure 63) and pivot open the hood. The machine has grease fittings that must be lubricated regularly with No. 2 General Purpose Lithium Base Grease. If the machine is operated under normal conditions, lubricate all bearings and bushings after every 50 hours of operation or immediately after every washing.
• Cutting unit carrier frame (2 per cutting unit) • Steering cylinder ball joints (2) (Figure 66) (Figure 68) • Cutting unit lift arm pivot (1 per cutting unit) (Figure 68) g015158 Figure 68 g009706 Figure 66 1. Top fitting on king pin • Tie rod ball joints (2) (Figure 66) • King pin bushings (2) (Figure 66). The top fitting • on the king pin should only be lubricated annually (2 pumps).
Engine Maintenance outside of primary filter and the canister. Avoid using high pressure air which could force dirt through the filter into the intake tract. Servicing the Air Cleaner This cleaning process prevents debris from migrating into the intake when the primary filter is removed. Service Interval: Every 400 hours Check the air cleaner body for damage which could cause an air leak. Replace if damaged. Check the whole intake system for leaks, damage or loose hose clamps. 3.
5. 6. Install the cover orienting the rubber outlet valve in a downward position—between approximately 5:00 to 7:00 when viewed from the end. 2. Unlock the hood latches and open the hood. 3. Remove the dipstick, wipe it clean, install the dipstick into the tube, and pull it out again. Reset the indicator (Figure 69) if it shows red. The oil level should be in the safe range (Figure 73).
Servicing the Diesel-Oxidation Catalyst (DOC) and the Soot Filter Service Interval: Every 6,000 hours or clean the soot filter if engine faults SPN 3720 FMI 16, SPN 3720 FMI 0, or SPN 3720 FMI 16 display in the InfoCenter. • If advisory message ADVISORY 179 displays in the InfoCenter, the DPF is nearing the recommended point for servicing the diesel-oxidation catalyst and the soot filter. g009713 Figure 74 1. Drain plug 3. Install the drain plug when the oil stops. 4.
Servicing the Water Separator Fuel System Maintenance Service Interval: Before each use or daily—Drain water or other contaminants from fuel filter/water separator. DANGER Under certain conditions, diesel fuel and fuel vapors are highly flammable and explosive. A fire or explosion from fuel can burn you and others and can cause property damage. Every 400 hours—Replace the fuel filter canister. Drain water or other contaminants from water separator daily.
Servicing the Fuel Filter Electrical System Maintenance Service Interval: Every 400 hours The engine fuel filter should be replaced after every 400 hours of operation. 1. Charging and Connecting the Battery Clean the area around the fuel filter head (Figure 79). WARNING CALIFORNIA Proposition 65 Warning Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling. 1.
DANGER WARNING Battery electrolyte contains sulfuric acid which is a deadly poison and causes severe burns. CALIFORNIA Proposition 65 Warning Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling. • Do not drink electrolyte and avoid contact with skin, eyes or clothing. Wear safety glasses to shield your eyes and rubber gloves to protect your hands.
Battery Care Service Interval: Every 50 hours Important: Before welding on the machine, disconnect the negative cable from the battery to prevent damage to the electrical system. Note: Check the battery condition weekly or after every 50 hours of operation. Keep the terminals and the entire battery case clean because a dirty battery will discharge slowly. To clean the battery, remove it from the machine, wash the entire case with a solution of baking soda and water. Rinse with clear water.
Drive System Maintenance 3. If the oil level is low, remove the plug at the 12 o’clock position and add oil until it begins to flow out of the hole at the 3 o’clock position. 4. Re-install both plugs. Checking the Torque of the Wheel Nuts 5. Repeat steps 1 through 4 on the opposite planetary gear assembly.
g009716 Figure 88 2. Fill plug 1. Check plug g019743 Figure 87 1. Brake housing 2. Drain plug 4. When all of the oil has drained from both locations, re-install the plug in the brake housing. 5. Rotate the wheel until the open plug hole in the planetary is at the twelve o'clock position. 6. Through the open hole, slowly fill the planetary with 0.65 liter (22 ounces) of high quality SAE 85W-140 wt. gear lube.
Adjusting the Traction Drive for Neutral The machine must not creep when traction pedal is released. If it does creep, an adjustment is required. 1. Park machine on a level surface, shut engine off, position speed control into LOW range and lower cutting units to the floor. Depress only the right brake pedal and engage the parking brake. 2. Jack up left side of machine until left front tire is off the shop floor. Support machine with jack stands to prevent it from falling accidentally. 3.
Cooling System Maintenance Servicing the Engine Cooling System Service Interval: Before each use or daily Remove debris from the engine area, oil cooler and radiator daily. Clean them more frequently in dirty conditions. 1. Unlatch and swing open rear screen (Figure 93). Clean the screen thoroughly of all debris. Note: To remove the screen, lift off the hinge pins. g020509 Figure 94 1.
Brake Maintenance Belt Maintenance Adjusting the Service Brakes Servicing the Alternator Belt Adjust the service brakes when there is more than 13 mm (1/2 inch) of “free travel" of the brake pedal, or when the brakes do not work effectively. Free travel is the distance the brake pedal moves before braking resistance is felt. Service Interval: Every 100 hours 1. 2. Check the condition and tension of the belts (Figure 96) after every 100 operating hours.
Hydraulic System Maintenance 3. Lubricate the new filter gasket and fill the filter with hydraulic fluid. Changing the Hydraulic Fluid Service Interval: Every 800 hours Change the hydraulic fluid after every 800 operating hours, in normal conditions. If the fluid becomes contaminated, contact your local Toro distributor because the system must be flushed. Contaminated fluid looks milky or black when compared to clean oil. 1. Turn the engine off and raise the hood. 2.
Checking the Hydraulic Lines and Hoses Cutting Unit Maintenance Backlapping the Cutting Units Service Interval: Before each use or daily Inspect the hydraulic lines and hoses daily for leaks, kinked lines, loose mounting supports, wear, loose fittings, weather deterioration, and chemical deterioration. Make all necessary repairs before operating. WARNING Contact with the reels or other moving parts can result in personal injury.
Storage Engine g015076 1. Drain the engine oil from the oil pan and install the drain plug. 2. Remove and discard the oil filter. Install a new oil filter. 3. Refill the oil pan with specified motor oil. 4. Start the engine and run it at idle speed for approximately two minutes. 5. Stop the engine. 6. Flush the fuel tank with fresh, clean diesel fuel. 7. Secure all of the fuel system fittings. 8. Thoroughly clean and service the air cleaner assembly. 9.
Notes:
The Toro Total Coverage Guarantee A Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
