Service Manual
Table Of Contents
- Title Page
- Revision History
- Reader Comments
- Preface
- Table of Contents
- 1 - Safety
- 2 - Product Records and Maintenance
- 3 - Yanmar Diesel Engine
- 4 - Kubota Diesel Engine
- 5 - Hydraulic System
- Specifications
- General Information
- Operator's Manual
- Hydraulic Component Locations
- Relieving Hydraulic System Pressure
- Traction Circuit Component Failure
- Towing Traction Unit
- Hydraulic Hoses
- Hydraulic Hose and Tube Installation (O-Ring Face Seal Fitting)
- Hydraulic Fitting Installation (SAE Straight Thread O-Ring Fitting into Component Port)
- Hydraulic Schematic
- Hydraulic Flow Diagrams
- Special Tools
- Troubleshooting
- Testing
- Traction Circuit - Charge Pressure Test
- Traction Circuit - Relief Pressure Test
- Traction Circuit - Piston (traction) Pump Flow Test
- Traction Circuit - Front Wheel Motor Case Drain Leakage Test
- Traction Circuit - Reverse Reducing Valve (PR) Pressure Test
- Traction Circuit - Rear Relief Valve (RV) Pressure Test
- Cutting Unit Circuit - Pressure Test
- Cutting Unit Circuit - Relief Pressure Test
- Cutting Unit Circuit - Cutting Unit Motor Case Drain Leakage Test
- Steering/Lift Circuit - Steering Relief Pressure Test
- Steering/Lift Circuit - Steering Cylinder Test
- Steering/Lift Circuit - Lift Relief Pressure Test
- Cooling Fan Circuit - Pressure Test
- Cooling Fan Circuit - Fan Motor Case Drain Leakage Test
- Gear Pump Flow Test (pump sections P2 thru P5)
- Adjustments
- Service and Repairs
- General Precautions for Removing and Installing Hydraulic System Components
- Check Hydraulic Lines and Hoses
- Priming Hydraulic Pumps
- Flush Hydraulic System
- Filtering Closed-Loop Traction Circuit
- Charge Hydraulic System
- Gear Pump
- Gear Pump Service
- Piston (Traction) Pump
- Piston (traction) Pump Service
- Rear Traction Manifold
- Rear Traction Manifold Service
- HI/LOW Range Manifold
- Front Wheel Motors
- Rear Axle Motor
- Front Wheel Motor and Rear Axle Motor Service
- Cutting Unit Motor
- Cutting Unit Motor Service
- Mow Control Manifold
- Mow Control Manifold Service
- Steering Control Valve
- Steering Control Valve Service
- Steering Cylinder
- Steering Cylinder Service
- Engine Cooling Fan Motor
- Engine Cooling Fan Motor Service
- Fan Control Manifold
- Fan Control Manifold Service
- Lift Manifold
- Lift Manifold Service
- Control Manifold Cartridge Valve Service
- Lift Junction Manifold
- Front Lift Cylinders
- Rear Lift Cylinders
- Lift Cylinder Service
- Hydraulic Reservoir
- Hydraulic Oil Cooler
- 6 - Electrical System
- General Information
- Electrical Drawings
- Special Tools
- InfoCenter Display
- Troubleshooting
- Electrical System Quick Checks
- Adjustments
- Component Testing
- Fusible Link Harness
- Fuses
- Toro Electronic Controllers (TEC)
- Ignition Switch
- Reel Enable/Disable Switch
- Engine Speed Switch (Yanmar Diesel Engine Only)
- Lower/Raise Joystick Switches
- Seat Switch
- Traction Neutral Switch
- Parking Brake Switch
- HI/LOW (Transport/Mow) Switch
- Cutting Unit Position Switch
- Backlap Switches
- Hydraulic Oil Temperature Sender
- Engine Temperature Sender (Kubota Diesel Engine Only)
- Relays with Four (4) Terminals
- Relays with Five (5) Terminals
- Hydraulic Solenoid Valve Coils
- Fuel Pump (Yanmar Diesel Engine Only)
- Fuel Pump (Kubota Diesel Engine Only)
- Fuel Stop Solenoid (Kubota Diesel Engines Only)
- CAN-bus Termination Resistor
- Diode Assembly
- Resistor Assembly
- Worklight Switch
- Service and Repairs
- 7 - Axles, Planetaries and Brakes
- 8 - Chassis
- 9 - DPA Cutting Units
- Table of Contents
- Specifications
- General Information
- Special Tools
- Gauge Bar Assembly
- Bedknife Screw Tool
- Handle Assembly
- Plastic Plug
- Cutting Unit Kickstand
- Spline Insert Tool
- Diameter/Circumference Measuring Tape
- Roller Rebuild Kit
- Turf Evaluator Tool
- Reel Bearing Installation Tool (cutting units with painted side plates)
- Cutting Reel Shim
- Cutting Performance Paper
- Pulley Alignment Tool
- Bedknife Top Angle Indicator and Mount
- Factors That Can Affect Cutting Performance
- Adjustments
- Service and Repairs
- Hydraulic Reel Motor
- Backlapping
- Bedbar Assembly
- Bedknife Replacement and Grinding
- Bedbar Adjuster Service
- Reel Assembly (cutting units with painted side plates)
- Reel Assembly Service (cutting units with painted side plates)
- Reel Assembly (cutting units with aluminum side plates)
- Reel Assembly Service (cutting units with aluminum side plates)
- Preparing Reel for Grinding
- Front Roller
- Rear Roller
- Roller Service
- Rear Roller Brush - Optional (cutting units with painted side plates)
- Rear Roller Brush - Optional (cutting units with aluminum side plates)
- 10 - Belt Driven Groomer (Optional)
- 11 - Universal Groomer (Optional)
- 12 - Foldout Drawings
- Electrical Drawing Designations
- Hydraulic Schematic
- Electrical Schematic - Traction Unit Model 03780 - Yanmar Engine (Serial numbers below 316000000)
- Electrical Schematic -- Traction UnitModel 03780 -- Yanmar Engine(Serial numbers 316000001 to 403350000)
- Electrical Schematic -- Traction UnitModel 03780 -- Yanmar Engine(Serial numbers above 403350001)
- Electrical Schematic - Traction Unit Model 03781 - Kubota Engine (Serial numbers below 316000000)
- Electrical Schematic -- Traction UnitModel 03781 -- Kubota Engine(Serial numbers 316000001 to 403350000)
- Electrical Schematic -- Traction UnitModel 03781 -- Kubota Engine(Serial numbers above 403350001)
- Electrical Schematic - Cab
- Main Wire Harness Drawing (Serial numbers below 316000000)
- Main Wire Harness Diagram (Serial numbers below 316000000)
- Main Wire Harness DrawingModel 03780 & 03781(Serial numbers 316000001 to 403350000)
- Main Wire Harness DiagramModel 03780 & 03781(Serial numbers 316000001 to 403350000)
- Main Wire Harness DrawingModel 03780 & 03781(Serial numbers 403350001 to 405699999)
- Main Wire Harness DiagramModel 03780 & 03781(Serial numbers 403350001 to 405699999)
- Main Wire Harness DrawingModel 03780 & 03781(Serial numbers above 405700000)
- Main Wire Harness DiagramModel 03780 & 03781(Serial numbers above 405700000)
- Engine Wire Harness Drawing - Yanmar
- Engine Wire Harness Diagram - Yanmar
- Engine Wire Harness Drawing - Kubota
- Engine Wire Harness Diagram - Kubota
- Seat and Console Wire Harness Drawing
- Seat and Wire Harness Diagram
- Power Center Wire Harness Drawing (Serial numbers below 403350000)
- Power Center Wire Harness Diagram (Serial numbers below 403350000)
- Power Center Wire Harness DrawingModel 03780 & 03781(Serial numbers above 403350001)
- Power Center Wire Harness DiagramModel 03780 & 03781(Serial numbers above 403350001)
Reelmaster 7000−D Hydraulic SystemPage 5 − 87
Service and Repairs
General Precautions for Removing and Installing Hydraulic System Components
Before Repair or Replacement of Hydraulic Compo-
nents
1. Before removing any parts from the hydraulic sys-
tem, park machine on a level surface, engage parking
brake, lower cutting units or attachments and stop en-
gine. Remove key from the ignition switch.
2. Clean machine before disconnecting, removing or
disassembling any hydraulic components. Make sure
hydraulic components, hoses connections and fittings
are cleaned thoroughly. Always keep in mind the need
for cleanliness when working on hydraulic equipment.
CAUTION
Operate all hydraulic controls to relieve system
pressure and avoid injury from pressurized hy-
draulic oil. Controls must be operated with the
ignition switch in RUN and the engine OFF. Make
sure all electrically operated control valves are
actuated. Return ignition switch to OFF when
pressure has been relieved. Remove key from
the ignition switch.
3. Put caps or plugs on any hydraulic lines, hydraulic fit-
tings and components left open or exposed to prevent
system contamination.
4. Put labels on disconnected hydraulic lines and
hoses for proper installation after repairs are completed.
5. Note the position of hydraulic fittings (especially el-
bow fittings) on hydraulic components before removal.
Mark parts if necessary to make sure they will be aligned
properly when installing hydraulic hoses and tubes.
After Repair or Replacement of Hydraulic Compo-
nents
1. Check oil level in the hydraulic reservoir and add cor-
rect oil if necessary. Drain and refill hydraulic system
reservoir and change oil filter if component failure was
severe or system is contaminated (see Flush Hydraulic
System in this section).
2. Lubricate O−rings and seals with clean hydraulic oil
before installing hydraulic components.
3. Make sure caps or plugs are removed from the hy-
draulic tubes, hydraulic fittings and components before
reconnecting.
4. Use proper tightening methods when installing hy-
draulic hoses and fittings (see Hydraulic Fitting Installa-
tion in the General Information section of this chapter).
5. After repairs, check control linkages or cables for
proper adjustment, binding or broken parts.
6. After disconnecting or replacing any hydraulic com-
ponents, operate machine functions slowly until air is
out of system (see Charge Hydraulic System in this sec-
tion).
7. Check for hydraulic oil leaks. Shut off engine and cor-
rect leaks if necessary. Check oil level in hydraulic reser-
voir and add correct oil if necessary.
Hydraulic
System