Service Manual
Table Of Contents
- Title Page
- Revision History
- Reader Comments
- Preface
- Table of Contents
- 1 - Safety
- 2 - Product Records and Maintenance
- 3 - Yanmar Diesel Engine
- 4 - Kubota Diesel Engine
- 5 - Hydraulic System
- Specifications
- General Information
- Operator's Manual
- Hydraulic Component Locations
- Relieving Hydraulic System Pressure
- Traction Circuit Component Failure
- Towing Traction Unit
- Hydraulic Hoses
- Hydraulic Hose and Tube Installation (O-Ring Face Seal Fitting)
- Hydraulic Fitting Installation (SAE Straight Thread O-Ring Fitting into Component Port)
- Hydraulic Schematic
- Hydraulic Flow Diagrams
- Special Tools
- Troubleshooting
- Testing
- Traction Circuit - Charge Pressure Test
- Traction Circuit - Relief Pressure Test
- Traction Circuit - Piston (traction) Pump Flow Test
- Traction Circuit - Front Wheel Motor Case Drain Leakage Test
- Traction Circuit - Reverse Reducing Valve (PR) Pressure Test
- Traction Circuit - Rear Relief Valve (RV) Pressure Test
- Cutting Unit Circuit - Pressure Test
- Cutting Unit Circuit - Relief Pressure Test
- Cutting Unit Circuit - Cutting Unit Motor Case Drain Leakage Test
- Steering/Lift Circuit - Steering Relief Pressure Test
- Steering/Lift Circuit - Steering Cylinder Test
- Steering/Lift Circuit - Lift Relief Pressure Test
- Cooling Fan Circuit - Pressure Test
- Cooling Fan Circuit - Fan Motor Case Drain Leakage Test
- Gear Pump Flow Test (pump sections P2 thru P5)
- Adjustments
- Service and Repairs
- General Precautions for Removing and Installing Hydraulic System Components
- Check Hydraulic Lines and Hoses
- Priming Hydraulic Pumps
- Flush Hydraulic System
- Filtering Closed-Loop Traction Circuit
- Charge Hydraulic System
- Gear Pump
- Gear Pump Service
- Piston (Traction) Pump
- Piston (traction) Pump Service
- Rear Traction Manifold
- Rear Traction Manifold Service
- HI/LOW Range Manifold
- Front Wheel Motors
- Rear Axle Motor
- Front Wheel Motor and Rear Axle Motor Service
- Cutting Unit Motor
- Cutting Unit Motor Service
- Mow Control Manifold
- Mow Control Manifold Service
- Steering Control Valve
- Steering Control Valve Service
- Steering Cylinder
- Steering Cylinder Service
- Engine Cooling Fan Motor
- Engine Cooling Fan Motor Service
- Fan Control Manifold
- Fan Control Manifold Service
- Lift Manifold
- Lift Manifold Service
- Control Manifold Cartridge Valve Service
- Lift Junction Manifold
- Front Lift Cylinders
- Rear Lift Cylinders
- Lift Cylinder Service
- Hydraulic Reservoir
- Hydraulic Oil Cooler
- 6 - Electrical System
- General Information
- Electrical Drawings
- Special Tools
- InfoCenter Display
- Troubleshooting
- Electrical System Quick Checks
- Adjustments
- Component Testing
- Fusible Link Harness
- Fuses
- Toro Electronic Controllers (TEC)
- Ignition Switch
- Reel Enable/Disable Switch
- Engine Speed Switch (Yanmar Diesel Engine Only)
- Lower/Raise Joystick Switches
- Seat Switch
- Traction Neutral Switch
- Parking Brake Switch
- HI/LOW (Transport/Mow) Switch
- Cutting Unit Position Switch
- Backlap Switches
- Hydraulic Oil Temperature Sender
- Engine Temperature Sender (Kubota Diesel Engine Only)
- Relays with Four (4) Terminals
- Relays with Five (5) Terminals
- Hydraulic Solenoid Valve Coils
- Fuel Pump (Yanmar Diesel Engine Only)
- Fuel Pump (Kubota Diesel Engine Only)
- Fuel Stop Solenoid (Kubota Diesel Engines Only)
- CAN-bus Termination Resistor
- Diode Assembly
- Resistor Assembly
- Worklight Switch
- Service and Repairs
- 7 - Axles, Planetaries and Brakes
- 8 - Chassis
- 9 - DPA Cutting Units
- Table of Contents
- Specifications
- General Information
- Special Tools
- Gauge Bar Assembly
- Bedknife Screw Tool
- Handle Assembly
- Plastic Plug
- Cutting Unit Kickstand
- Spline Insert Tool
- Diameter/Circumference Measuring Tape
- Roller Rebuild Kit
- Turf Evaluator Tool
- Reel Bearing Installation Tool (cutting units with painted side plates)
- Cutting Reel Shim
- Cutting Performance Paper
- Pulley Alignment Tool
- Bedknife Top Angle Indicator and Mount
- Factors That Can Affect Cutting Performance
- Adjustments
- Service and Repairs
- Hydraulic Reel Motor
- Backlapping
- Bedbar Assembly
- Bedknife Replacement and Grinding
- Bedbar Adjuster Service
- Reel Assembly (cutting units with painted side plates)
- Reel Assembly Service (cutting units with painted side plates)
- Reel Assembly (cutting units with aluminum side plates)
- Reel Assembly Service (cutting units with aluminum side plates)
- Preparing Reel for Grinding
- Front Roller
- Rear Roller
- Roller Service
- Rear Roller Brush - Optional (cutting units with painted side plates)
- Rear Roller Brush - Optional (cutting units with aluminum side plates)
- 10 - Belt Driven Groomer (Optional)
- 11 - Universal Groomer (Optional)
- 12 - Foldout Drawings
- Electrical Drawing Designations
- Hydraulic Schematic
- Electrical Schematic - Traction Unit Model 03780 - Yanmar Engine (Serial numbers below 316000000)
- Electrical Schematic -- Traction UnitModel 03780 -- Yanmar Engine(Serial numbers 316000001 to 403350000)
- Electrical Schematic -- Traction UnitModel 03780 -- Yanmar Engine(Serial numbers above 403350001)
- Electrical Schematic - Traction Unit Model 03781 - Kubota Engine (Serial numbers below 316000000)
- Electrical Schematic -- Traction UnitModel 03781 -- Kubota Engine(Serial numbers 316000001 to 403350000)
- Electrical Schematic -- Traction UnitModel 03781 -- Kubota Engine(Serial numbers above 403350001)
- Electrical Schematic - Cab
- Main Wire Harness Drawing (Serial numbers below 316000000)
- Main Wire Harness Diagram (Serial numbers below 316000000)
- Main Wire Harness DrawingModel 03780 & 03781(Serial numbers 316000001 to 403350000)
- Main Wire Harness DiagramModel 03780 & 03781(Serial numbers 316000001 to 403350000)
- Main Wire Harness DrawingModel 03780 & 03781(Serial numbers 403350001 to 405699999)
- Main Wire Harness DiagramModel 03780 & 03781(Serial numbers 403350001 to 405699999)
- Main Wire Harness DrawingModel 03780 & 03781(Serial numbers above 405700000)
- Main Wire Harness DiagramModel 03780 & 03781(Serial numbers above 405700000)
- Engine Wire Harness Drawing - Yanmar
- Engine Wire Harness Diagram - Yanmar
- Engine Wire Harness Drawing - Kubota
- Engine Wire Harness Diagram - Kubota
- Seat and Console Wire Harness Drawing
- Seat and Wire Harness Diagram
- Power Center Wire Harness Drawing (Serial numbers below 403350000)
- Power Center Wire Harness Diagram (Serial numbers below 403350000)
- Power Center Wire Harness DrawingModel 03780 & 03781(Serial numbers above 403350001)
- Power Center Wire Harness DiagramModel 03780 & 03781(Serial numbers above 403350001)
Reelmaster 7000--D
DPA Cutting Units
Page 9 -- 23
Removal (Fig. 32)
1. Remove lock nut (item 3), compression spring and
washer from bedbar adjuster screw (item 4).
2. Remove bedbar assembly (see Bedbar Assembly
Removal in this section).
3. Remove bedbar adjuster screw (left hand threads)
from the bedbar adjuster shaft (item 10).
4. Remove adjuster shaft from cutting unit frame:
A. On early production cutting units (Fig. 32 A), re-
move retaining ring and wave washer from adjuster
shaft. Slide adjus ter shaft from cutting unit frame.
B. On current production cutting units (Fig. 32 B), re-
move lock nut and flat washer from adjuster shaft.
Slide adjuster shaft and wave washer from cutting
unit frame.
5. Inspect flange bushings (item 5) in cutting unit frame
and remove if necessary.
6. If detent (item 7) is damaged, remove it from cutting
unit side plate.
Installation (Fig. 32)
1. If detent (item 7) was removed, apply Loctite #243
(or equivalent) to threads of cap screw and secure det-
ent to cutting unit side plate with cap screw. Tighten cap
screw from 14 to 16 ft--lb (19 to 21 N--m).
2. If flange bushings (item 5) were removed, apply anti-
seize lubricant to bore of cutting unit frame. Align key on
bushing to slot in frame and install bushings into frame.
Apply antiseize lubricant to bore of each flange bushing.
3. Install adjuster shaft to cutting unit frame:
A. On early production cutting units (Fig. 32 A), slide
bedbar adjuster shaft into flange bushings in cutting
unit frame. Secure adjuster shaft with wave washer
and retaining ring.
B. On current production cutting units (Fig. 32 B),
slide wave washer onto adjuster shaft and then slide
adjuster shaft into flange bushings in cutting unit
frame. Secure adjuster shaft with flat washer and
lock nut. Tighten lock nut to shoulder of adjuster shaft
and then torque lock nut from 15 to 20 ft--lb (21 to 27
N--m).
NOTE: Inside threads in bedbar adjuster shaft (item 4)
are left--hand threads.
4. Apply antiseize lubricant to left hand threads threads
of bedbar adjuster screw (item 4). Thread bedbar ad-
juster screw into adjuster shaft (item 10).
5. Install washer (item 11), compression spring and
lock nut onto adjuster screw.
6. Install bedbar assembly (see Bedbar Assembly
Installation in this section).
7. Adjust cutting unit (see Cutting Unit Operator’s
Manual).
DPA Cutting
Units