Service Manual
Table Of Contents
- Title Page
- Revision History
- Reader Comments
- Preface
- Table of Contents
- 1 - Safety
- 2 - Product Records and Maintenance
- 3 - Yanmar Diesel Engine
- 4 - Kubota Diesel Engine
- 5 - Hydraulic System
- Specifications
- General Information
- Operator's Manual
- Hydraulic Component Locations
- Relieving Hydraulic System Pressure
- Traction Circuit Component Failure
- Towing Traction Unit
- Hydraulic Hoses
- Hydraulic Hose and Tube Installation (O-Ring Face Seal Fitting)
- Hydraulic Fitting Installation (SAE Straight Thread O-Ring Fitting into Component Port)
- Hydraulic Schematic
- Hydraulic Flow Diagrams
- Special Tools
- Troubleshooting
- Testing
- Traction Circuit - Charge Pressure Test
- Traction Circuit - Relief Pressure Test
- Traction Circuit - Piston (traction) Pump Flow Test
- Traction Circuit - Front Wheel Motor Case Drain Leakage Test
- Traction Circuit - Reverse Reducing Valve (PR) Pressure Test
- Traction Circuit - Rear Relief Valve (RV) Pressure Test
- Cutting Unit Circuit - Pressure Test
- Cutting Unit Circuit - Relief Pressure Test
- Cutting Unit Circuit - Cutting Unit Motor Case Drain Leakage Test
- Steering/Lift Circuit - Steering Relief Pressure Test
- Steering/Lift Circuit - Steering Cylinder Test
- Steering/Lift Circuit - Lift Relief Pressure Test
- Cooling Fan Circuit - Pressure Test
- Cooling Fan Circuit - Fan Motor Case Drain Leakage Test
- Gear Pump Flow Test (pump sections P2 thru P5)
- Adjustments
- Service and Repairs
- General Precautions for Removing and Installing Hydraulic System Components
- Check Hydraulic Lines and Hoses
- Priming Hydraulic Pumps
- Flush Hydraulic System
- Filtering Closed-Loop Traction Circuit
- Charge Hydraulic System
- Gear Pump
- Gear Pump Service
- Piston (Traction) Pump
- Piston (traction) Pump Service
- Rear Traction Manifold
- Rear Traction Manifold Service
- HI/LOW Range Manifold
- Front Wheel Motors
- Rear Axle Motor
- Front Wheel Motor and Rear Axle Motor Service
- Cutting Unit Motor
- Cutting Unit Motor Service
- Mow Control Manifold
- Mow Control Manifold Service
- Steering Control Valve
- Steering Control Valve Service
- Steering Cylinder
- Steering Cylinder Service
- Engine Cooling Fan Motor
- Engine Cooling Fan Motor Service
- Fan Control Manifold
- Fan Control Manifold Service
- Lift Manifold
- Lift Manifold Service
- Control Manifold Cartridge Valve Service
- Lift Junction Manifold
- Front Lift Cylinders
- Rear Lift Cylinders
- Lift Cylinder Service
- Hydraulic Reservoir
- Hydraulic Oil Cooler
- 6 - Electrical System
- General Information
- Electrical Drawings
- Special Tools
- InfoCenter Display
- Troubleshooting
- Electrical System Quick Checks
- Adjustments
- Component Testing
- Fusible Link Harness
- Fuses
- Toro Electronic Controllers (TEC)
- Ignition Switch
- Reel Enable/Disable Switch
- Engine Speed Switch (Yanmar Diesel Engine Only)
- Lower/Raise Joystick Switches
- Seat Switch
- Traction Neutral Switch
- Parking Brake Switch
- HI/LOW (Transport/Mow) Switch
- Cutting Unit Position Switch
- Backlap Switches
- Hydraulic Oil Temperature Sender
- Engine Temperature Sender (Kubota Diesel Engine Only)
- Relays with Four (4) Terminals
- Relays with Five (5) Terminals
- Hydraulic Solenoid Valve Coils
- Fuel Pump (Yanmar Diesel Engine Only)
- Fuel Pump (Kubota Diesel Engine Only)
- Fuel Stop Solenoid (Kubota Diesel Engines Only)
- CAN-bus Termination Resistor
- Diode Assembly
- Resistor Assembly
- Worklight Switch
- Service and Repairs
- 7 - Axles, Planetaries and Brakes
- 8 - Chassis
- 9 - DPA Cutting Units
- Table of Contents
- Specifications
- General Information
- Special Tools
- Gauge Bar Assembly
- Bedknife Screw Tool
- Handle Assembly
- Plastic Plug
- Cutting Unit Kickstand
- Spline Insert Tool
- Diameter/Circumference Measuring Tape
- Roller Rebuild Kit
- Turf Evaluator Tool
- Reel Bearing Installation Tool (cutting units with painted side plates)
- Cutting Reel Shim
- Cutting Performance Paper
- Pulley Alignment Tool
- Bedknife Top Angle Indicator and Mount
- Factors That Can Affect Cutting Performance
- Adjustments
- Service and Repairs
- Hydraulic Reel Motor
- Backlapping
- Bedbar Assembly
- Bedknife Replacement and Grinding
- Bedbar Adjuster Service
- Reel Assembly (cutting units with painted side plates)
- Reel Assembly Service (cutting units with painted side plates)
- Reel Assembly (cutting units with aluminum side plates)
- Reel Assembly Service (cutting units with aluminum side plates)
- Preparing Reel for Grinding
- Front Roller
- Rear Roller
- Roller Service
- Rear Roller Brush - Optional (cutting units with painted side plates)
- Rear Roller Brush - Optional (cutting units with aluminum side plates)
- 10 - Belt Driven Groomer (Optional)
- 11 - Universal Groomer (Optional)
- 12 - Foldout Drawings
- Electrical Drawing Designations
- Hydraulic Schematic
- Electrical Schematic - Traction Unit Model 03780 - Yanmar Engine (Serial numbers below 316000000)
- Electrical Schematic -- Traction UnitModel 03780 -- Yanmar Engine(Serial numbers 316000001 to 403350000)
- Electrical Schematic -- Traction UnitModel 03780 -- Yanmar Engine(Serial numbers above 403350001)
- Electrical Schematic - Traction Unit Model 03781 - Kubota Engine (Serial numbers below 316000000)
- Electrical Schematic -- Traction UnitModel 03781 -- Kubota Engine(Serial numbers 316000001 to 403350000)
- Electrical Schematic -- Traction UnitModel 03781 -- Kubota Engine(Serial numbers above 403350001)
- Electrical Schematic - Cab
- Main Wire Harness Drawing (Serial numbers below 316000000)
- Main Wire Harness Diagram (Serial numbers below 316000000)
- Main Wire Harness DrawingModel 03780 & 03781(Serial numbers 316000001 to 403350000)
- Main Wire Harness DiagramModel 03780 & 03781(Serial numbers 316000001 to 403350000)
- Main Wire Harness DrawingModel 03780 & 03781(Serial numbers 403350001 to 405699999)
- Main Wire Harness DiagramModel 03780 & 03781(Serial numbers 403350001 to 405699999)
- Main Wire Harness DrawingModel 03780 & 03781(Serial numbers above 405700000)
- Main Wire Harness DiagramModel 03780 & 03781(Serial numbers above 405700000)
- Engine Wire Harness Drawing - Yanmar
- Engine Wire Harness Diagram - Yanmar
- Engine Wire Harness Drawing - Kubota
- Engine Wire Harness Diagram - Kubota
- Seat and Console Wire Harness Drawing
- Seat and Wire Harness Diagram
- Power Center Wire Harness Drawing (Serial numbers below 403350000)
- Power Center Wire Harness Diagram (Serial numbers below 403350000)
- Power Center Wire Harness DrawingModel 03780 & 03781(Serial numbers above 403350001)
- Power Center Wire Harness DiagramModel 03780 & 03781(Serial numbers above 403350001)
Reelmaster 7000--D
DPA Cutting Units
Page 9 -- 41
3. From the roller tube end with only the inner seal
installed, carefully install the roller shaft into the roller
tube. Make sure that seals are not damaged as shaft is
installed.
4. Install new bearing and outer seals into second end
of roller tube:
A. Position a second new bearing to roller shaft and
tube. Position washer (see Special Tools) on bearing
to allow pressing on both inner and outer bearing
races simultaneously.
B. Use washer and bearing/outer seal tool (see
Special Tools) with a soft face hammer to fully seat
bearing (Fig. 54). After bearing installation, make
sure that shaft freely rotates and that no binding is
detected. If necessary, lightly tap bearing and/or
shaft ends to align shaft and bearings. Remove
washer from roller.
C. Apply a small amount of grease around the lip of
both outer seals.
D. Carefully install first outer seal into roller tube
making sure that seal lip (and garter spring) faces
end of tube. Use bearing/outer seal tool (see Special
Tools) and soft face hammer to lightly seat seal (Fig.
55). Make sure that shaft and bearings still freely ro-
tate after seal installation.
E. Using the same process, install second outer
seal making sure to not crush the installed outer seal.
Again, make sure that shaft and bearings still freely
rotate.
IMPORTANT: Make sure that all grease is removed
from shaft threads to prevent bearing lock nut loos-
ening.
5. Thoroughly clean threads on both ends of roller
shaft.
NOTE: If original bearing lock nut(s) are being used,
apply Loctite #243 (or equivalent) to threads of lock
nut(s).
6. Install bearing lock nut onto each end of the roller
shaft. Make sure that outer seals are not damaged dur-
ing nut installation. Torque bearing lock nuts from 50 to
6 0 f t -- l b ( 6 8 t o 8 1 N -- m ) .
7. If grease fittings were removed from end of roller
shaft, install fittings in shaft.
NOTE: After roller is installed to cutting unit, lubricate
roller grease fittings, rotate roller to properly distribute
grease in bearings and clean excess grease from roller
ends. A properly assembled roller should rotate with
less than 5 in--lb (0.68 N--m) resistance.
1. Roller tube
2. Inner seal
3. Bearing
4. Outer seal
5. Bearing/outer seal tool
Figure 53
3421 5
1. Roller tube
2. Roller shaft
3. Inner seal
4. Bearing
5. Washer
6. Bearing/outer seal tool
Figure 54
342156
1. Roller tube
2. Roller shaft
3. Inner seal
4. Bearing
5. Outer seal
6. Bearing/outer seal tool
Figure 55
342156
DPA Cutting
Units