Service Manual
Table Of Contents
- Title Page
- Revision History
- Reader Comments
- Preface
- Table of Contents
- 1 - Safety
- 2 - Product Records and Maintenance
- 3 - Yanmar Diesel Engine
- 4 - Kubota Diesel Engine
- 5 - Hydraulic System
- Specifications
- General Information
- Operator's Manual
- Hydraulic Component Locations
- Relieving Hydraulic System Pressure
- Traction Circuit Component Failure
- Towing Traction Unit
- Hydraulic Hoses
- Hydraulic Hose and Tube Installation (O-Ring Face Seal Fitting)
- Hydraulic Fitting Installation (SAE Straight Thread O-Ring Fitting into Component Port)
- Hydraulic Schematic
- Hydraulic Flow Diagrams
- Special Tools
- Troubleshooting
- Testing
- Traction Circuit - Charge Pressure Test
- Traction Circuit - Relief Pressure Test
- Traction Circuit - Piston (traction) Pump Flow Test
- Traction Circuit - Front Wheel Motor Case Drain Leakage Test
- Traction Circuit - Reverse Reducing Valve (PR) Pressure Test
- Traction Circuit - Rear Relief Valve (RV) Pressure Test
- Cutting Unit Circuit - Pressure Test
- Cutting Unit Circuit - Relief Pressure Test
- Cutting Unit Circuit - Cutting Unit Motor Case Drain Leakage Test
- Steering/Lift Circuit - Steering Relief Pressure Test
- Steering/Lift Circuit - Steering Cylinder Test
- Steering/Lift Circuit - Lift Relief Pressure Test
- Cooling Fan Circuit - Pressure Test
- Cooling Fan Circuit - Fan Motor Case Drain Leakage Test
- Gear Pump Flow Test (pump sections P2 thru P5)
- Adjustments
- Service and Repairs
- General Precautions for Removing and Installing Hydraulic System Components
- Check Hydraulic Lines and Hoses
- Priming Hydraulic Pumps
- Flush Hydraulic System
- Filtering Closed-Loop Traction Circuit
- Charge Hydraulic System
- Gear Pump
- Gear Pump Service
- Piston (Traction) Pump
- Piston (traction) Pump Service
- Rear Traction Manifold
- Rear Traction Manifold Service
- HI/LOW Range Manifold
- Front Wheel Motors
- Rear Axle Motor
- Front Wheel Motor and Rear Axle Motor Service
- Cutting Unit Motor
- Cutting Unit Motor Service
- Mow Control Manifold
- Mow Control Manifold Service
- Steering Control Valve
- Steering Control Valve Service
- Steering Cylinder
- Steering Cylinder Service
- Engine Cooling Fan Motor
- Engine Cooling Fan Motor Service
- Fan Control Manifold
- Fan Control Manifold Service
- Lift Manifold
- Lift Manifold Service
- Control Manifold Cartridge Valve Service
- Lift Junction Manifold
- Front Lift Cylinders
- Rear Lift Cylinders
- Lift Cylinder Service
- Hydraulic Reservoir
- Hydraulic Oil Cooler
- 6 - Electrical System
- General Information
- Electrical Drawings
- Special Tools
- InfoCenter Display
- Troubleshooting
- Electrical System Quick Checks
- Adjustments
- Component Testing
- Fusible Link Harness
- Fuses
- Toro Electronic Controllers (TEC)
- Ignition Switch
- Reel Enable/Disable Switch
- Engine Speed Switch (Yanmar Diesel Engine Only)
- Lower/Raise Joystick Switches
- Seat Switch
- Traction Neutral Switch
- Parking Brake Switch
- HI/LOW (Transport/Mow) Switch
- Cutting Unit Position Switch
- Backlap Switches
- Hydraulic Oil Temperature Sender
- Engine Temperature Sender (Kubota Diesel Engine Only)
- Relays with Four (4) Terminals
- Relays with Five (5) Terminals
- Hydraulic Solenoid Valve Coils
- Fuel Pump (Yanmar Diesel Engine Only)
- Fuel Pump (Kubota Diesel Engine Only)
- Fuel Stop Solenoid (Kubota Diesel Engines Only)
- CAN-bus Termination Resistor
- Diode Assembly
- Resistor Assembly
- Worklight Switch
- Service and Repairs
- 7 - Axles, Planetaries and Brakes
- 8 - Chassis
- 9 - DPA Cutting Units
- Table of Contents
- Specifications
- General Information
- Special Tools
- Gauge Bar Assembly
- Bedknife Screw Tool
- Handle Assembly
- Plastic Plug
- Cutting Unit Kickstand
- Spline Insert Tool
- Diameter/Circumference Measuring Tape
- Roller Rebuild Kit
- Turf Evaluator Tool
- Reel Bearing Installation Tool (cutting units with painted side plates)
- Cutting Reel Shim
- Cutting Performance Paper
- Pulley Alignment Tool
- Bedknife Top Angle Indicator and Mount
- Factors That Can Affect Cutting Performance
- Adjustments
- Service and Repairs
- Hydraulic Reel Motor
- Backlapping
- Bedbar Assembly
- Bedknife Replacement and Grinding
- Bedbar Adjuster Service
- Reel Assembly (cutting units with painted side plates)
- Reel Assembly Service (cutting units with painted side plates)
- Reel Assembly (cutting units with aluminum side plates)
- Reel Assembly Service (cutting units with aluminum side plates)
- Preparing Reel for Grinding
- Front Roller
- Rear Roller
- Roller Service
- Rear Roller Brush - Optional (cutting units with painted side plates)
- Rear Roller Brush - Optional (cutting units with aluminum side plates)
- 10 - Belt Driven Groomer (Optional)
- 11 - Universal Groomer (Optional)
- 12 - Foldout Drawings
- Electrical Drawing Designations
- Hydraulic Schematic
- Electrical Schematic - Traction Unit Model 03780 - Yanmar Engine (Serial numbers below 316000000)
- Electrical Schematic -- Traction UnitModel 03780 -- Yanmar Engine(Serial numbers 316000001 to 403350000)
- Electrical Schematic -- Traction UnitModel 03780 -- Yanmar Engine(Serial numbers above 403350001)
- Electrical Schematic - Traction Unit Model 03781 - Kubota Engine (Serial numbers below 316000000)
- Electrical Schematic -- Traction UnitModel 03781 -- Kubota Engine(Serial numbers 316000001 to 403350000)
- Electrical Schematic -- Traction UnitModel 03781 -- Kubota Engine(Serial numbers above 403350001)
- Electrical Schematic - Cab
- Main Wire Harness Drawing (Serial numbers below 316000000)
- Main Wire Harness Diagram (Serial numbers below 316000000)
- Main Wire Harness DrawingModel 03780 & 03781(Serial numbers 316000001 to 403350000)
- Main Wire Harness DiagramModel 03780 & 03781(Serial numbers 316000001 to 403350000)
- Main Wire Harness DrawingModel 03780 & 03781(Serial numbers 403350001 to 405699999)
- Main Wire Harness DiagramModel 03780 & 03781(Serial numbers 403350001 to 405699999)
- Main Wire Harness DrawingModel 03780 & 03781(Serial numbers above 405700000)
- Main Wire Harness DiagramModel 03780 & 03781(Serial numbers above 405700000)
- Engine Wire Harness Drawing - Yanmar
- Engine Wire Harness Diagram - Yanmar
- Engine Wire Harness Drawing - Kubota
- Engine Wire Harness Diagram - Kubota
- Seat and Console Wire Harness Drawing
- Seat and Wire Harness Diagram
- Power Center Wire Harness Drawing (Serial numbers below 403350000)
- Power Center Wire Harness Diagram (Serial numbers below 403350000)
- Power Center Wire Harness DrawingModel 03780 & 03781(Serial numbers above 403350001)
- Power Center Wire Harness DiagramModel 03780 & 03781(Serial numbers above 403350001)
Reelmaster 7000−D Hydraulic SystemPage 5 − 5
Towing Traction Unit
IMPORTANT: If towing limits are exceeded, severe
damage to the piston pump may occur.
If it becomes necessary to tow (or push) the machine,
tow (or push) in a forward direction, at a speed below
3 mph (4.8 kph) and for a distance less than 1/4 mile
(0.4 km). The piston (traction) pump is equipped with a
bypass valve that needs to be turned 90
o
for towing
(Fig. 1). Do not turn bypass valve when engine is run-
ning.
IMPORTANT: If the machine must be pushed or
towed in the reverse direction, the bypass valve
needs to be turned 90
o
, and a check valve in the rear
traction manifold must be bypassed. Do not exceed
3 mph (4.8 kph) or a distance of ¼ mile (0.4 km) when
pushing or towing the machine in reverse.
The following Toro parts are needed to bypass the check
valve:
59−7410 diagnostic fitting
354−79 diagnostic fitting cap
95−8843 hydraulic hose
95−0985 coupler fitting (2)
340−77 hydraulic fitting (2)
NOTE: The #6 zero leak plug on the rear traction mani-
fold has a tapered sealing surface on the plug head.
Lightly rap the plug head using a punch and hammer be-
fore using an allen wrench to remove the plug. The im-
pact will allow plug removal with less chance of damage
to the socket head of the plug.
1. To bypass the check valve, install a diagnostic fitting
in the unmarked port located between ports M8 and P2
on the rear traction manifold (Fig. 2).
2. Connect a hydraulic hose between the diagnostic fit-
ting installed in the rear traction manifold and the re-
verse traction pressure test port (Fig. 3).
1. Bypass valve location
Figure 1
1
1. Rear traction manifold
(behind front left wheel)
2. Unmarked port
Figure 2
12 1
1. Reverse traction
pressure test port
2. Hydraulic oil return filte
r
Figure 3
1
2
Hydraulic
System