Operator's Manual
Adjusting Height of Cut
– 12 –
Desired Desired Second Front Height- Rear Height- Rear Support
Height of Attitude Screw “A” of-Cut Rod “B” of-Cut Rod Bracket (Fig. 8)
Cut (mm) (degrees) (mm) Fig. 7 (mm) (Fig. 8) “C” (mm) (Fig. 8) (location)
10mm 2°* 4.6 41.3 47.4 top
4°* 5.9 46.4 41.3 top
6°* – 54.5 35.2 top
8°* – – – top
13mm 2°* 7.6 38.1 44.2 top
4°* 9.0 43.2 38.1 top
6°* 10.5 48.3 32.1 top
8°* – – – top
2° 5.8 34.5 48.5 top
4° 7.2 39.6 42.4 top
6° 8.7 39.6 26.3 top
8° – 49.9 30.3 top
16mm 2° 9.0 31.3 45.3 top
4° 10.4 36.4 29.2 top
6° 11.9 41.6 24.6 top
8° – 46.7 27.1 top
19mm 2° 12.1 28.2 42.1 top
4° 13.6 33.3 36.0 top
6° 15.0 38.4 29.9 top
8° 16.5 43.5 23.9✝ top
22mm 2° 15.3 25.0✝ 38.9 top
4° 16.8 30.1 45.5 top
6° 18.2 35.2 26.8 top
8° 19.7 40.3 20.7✝ top
25mm 2° 18.5 21.8 35.7 top
4° 19.9 26.9 29.6 top
6° 21.4 32.0 23.6✝ top
8° 22.9 37.2 17.6✝ top
29mm 2° 21.7 18.6✝ 32.6 top
4° 23.1 23.7✝ 25.5 top
6° 24.6 28.9 20.4✝ top
8° 26.0 35.3 14.4✝ top
32mm 2° 24.8 15.4✝ 29.4 top
4° 26.3 20.5✝ 23.3✝ top
6° 27.7 25.7 17.2✝ top
8° 29.2 30.8 11.2✝ top
35mm 2° 28.0 12.2✝ 26.2 top
4° 29.5 17.4✝ 20.1✝ top
6° 30.9 22.5✝ 14.0✝ top
8° 32.4 27.6 8.0✝ top
38mm 2° 31.2 9.0✝ 23.0✝ top
4° 32.6 14.2✝ 16.9✝ top
6° 34.1 19.3✝ 10.9✝ top
8° 35.6 24.5✝ 4.9✝ top
41mm 2° – 5.8✝ 35.7 bottom
4° 35.8 11.0✝ 29.6 bottom
6° 36.2 16.2✝ 23.6✝ bottom
8° 38.7 21.3✝ 17.6✝ bottom
45mm 2° – 2.6✝ 32.5 bottom
4° 39.0 7.8✝ 26.4 bottom
6° 40.4 13.0✝ 20.4✝ bottom
8° 41.9 18.1✝ 14.4✝ bottom
* Optional Low-Cut Bedknife, Toro part no. 93-9774, is required for height of cut below 13mm
✝ For front “B” or rear roller distances “C” less than 25mm, order a long cone nut (Part No. 95-2720) to
replace the bottom cone nut for improved support.