Installation Instructions

ManualsBrandsToro ManualsAttachmentsGrass Basket Kit, Reelmaster 3550 Series 22-inch Cutting Unit

FormNo.3375-905RevC

GrassBasketKit

Reelmaster

3550Series18and22-inchCuttingUnit

ModelNo.03919

ModelNo.03920

ModelNo.03921

InstallationInstructions

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Basketguide(18inch)

Basketcamlock(18inch)

Basketcamlock(22inch)

Rollpin(18inch)

Rollpin(22inch)

Washer1

Lefthandtorsionspring(Gold)

Righthandtorsionspring(Black)

Basketcollar(18inch)

Basketcollar(22inch)

Flatwasher(.344x.875)

Bolt(5/16x1-1/4inches)(22inch)

Bolt(5/16x1-1/4inches)(18inch)

Bolt(5/16x1/2inch)(18inch)

Plasticwasher(18inch)

Plasticwasher(22inch)

Spacer

Bolt(3/8–16x1-1/4inch)

Installthebasketguidesandbrackets.

Cutoffbar

Bolt(1/4x1–3/4inches)

Locknut(1/4inch)

Installthecutoffbar.

Basketassembly1

Mountthebasketassemblytothe

cuttingunit.

Nopartsrequired

–

Adjustthebasketposition.

Operator'sManual

PartsCatalog

Readthedocumentationandstoreitin

asafelocation.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

*3375-905*C

Summary of content (8 pages)

PAGE 1
Form No. 3375-905 Rev C Grass Basket Kit Reelmaster® 3550 Series 18 and 22-inch Cutting Unit Model No. 03919 Model No. 03920 Model No. 03921 Installation Instructions Note: Determine the left and right sides of the machine from the normal operating position. Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 © 2013—The Toro® Company 8111 Lyndale Avenue South Bloomington, MN 55420 Description Qty.
PAGE 2
1 Installing the Basket Guides and Brackets Parts needed for this procedure: 1 Basket guide (18 inch) 1 Basket cam lock (18 inch) 2 Basket cam lock (22 inch) 1 Roll pin (18 inch) 2 Roll pin (22 inch) 1. Center basket 5. Right front basket 1 Washer 2. Left rear basket 6. Basket guide 3. Right rear basket 7. Basket cam lock 1 Left hand torsion spring (Gold) 1 Right hand torsion spring (Black) 1 Basket collar (18 inch) 2 Basket collar (22 inch) 2 Flat washer (.344 x .
PAGE 3
. Mount a basket guide to the appropriate side of each cutting unit carrier frame (Figure 1) with a bolt (5/16 x 1/2 inch) and a flat washer (.344 x .875). 5. Note: Position the components as shown in Figure 3. Install a bolt (3/8–16 x 1-1/4 inch) and a new spacer, and secure them using the nut provided in the kit (Figure 5). Note: Ensure that the flat washer is between the frame and the side plate, and that the flat washer is placed around the spacer shown in Figure 5. Figure 3 1. Carrier frame 3.
PAGE 4
Important: Ensure that the plastic washer (item 3) is centered correctly on the basket collar (item 6) otherwise the cam lock may not lock properly and may stick when rotated. If installed correctly, the plastic washer will rotate smoothly when the cam lock is rotated back and forth. Figure 7 Figure 6 1. Carrier frame 5. Torsion spring (Left shown) (Gold color) 2. Roll pin 6. Basket collar 3. Plastic washer 7. Flat washer (.344 x .875) 4. Basket bracket 8.
PAGE 5
3 Mounting the Basket Assembly to the Cutting Unit Parts needed for this procedure: 1 Basket assembly Procedure Mount a basket to each cutting unit carrier frame by inserting the basket mounting pin into the basket guide bracket and pressing the opposite mounting pin into the cam lock basket bracket (Figure 8). Figure 8 1. Basket mounting pin 2. Basket guide 3.
PAGE 6
Rear basket installation: 1. Slide the basket vertically under the machine with the open end of the basket facing upwards just past the inside of the tire (Figure 9A). 2. Insert the basket mounting pin into the basket guide stop (Figure 9B). 3. Rotate the back side of the basket upwards so that the inside basket stop on the basket is in front of the carrier frame stop (Figure 9C). 4. Press the opposite mounting pin into the basket cam lock (Figure 9D). Rear basket removal: 1.
PAGE 7
4 5 Adjusting the Basket Position Reading/Storing the Documentation No Parts Required Parts needed for this procedure: Procedure Make sure that the basket is parallel to the cutting unit or slightly raised in front with a minimum clearance of .250 inches (6 mm) between the lip of the basket and the reel, and a minimum clearance of .250 inches (6 mm) between the front roller and the bottom of the basket. To adjust the basket position, proceed as follows: with a minimum clearance of .
PAGE 8
Declaration of Incorporation The Toro Company, 8111 Lyndale Ave. South, Bloomington, MN, USA declares that the following unit(s) conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain Toro models as indicated on the relevant Declarations of Conformity. Model No. 03919 03920 03921 Serial No.