Installation Instructions

ManualsBrandsToro ManualsAttachmentsFlexible Grass Basket Kit, Reelmaster 3550 Series 18-inch Cutting Unit

FormNo.3397-826RevA

FlexibleGrassBasketKitorExtendedFlexible

GrassBasketKit

Reelmaster

3550Series18-inchCuttingUnit

ModelNo.03923

ModelNo.03924

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Basketguide1

Basketbracket2

Screw(5/16x1/2inch)

Rollpin1

Lefttorsionspring(gold)

Righttorsionspring(black)

Basketcollar1

Washer(3/8x7/8inch)

Bolt(5/16x1-1/4inches)

Plasticwasher1

Installthebasketguidesandbrackets.

Spacer

Flangelocknut2

Bolt(3/8x1-1/4inches)

Installthespacers.

Cutoffbar

Bolt(1/4x1-3/4inches)

Locknut(1/4inch)

Installthecutoffbar.

Nopartsrequired

–

Removethegrassdeectors(if

installed).

Basketrod1

Basketplate2

Flangescrew(5/16x1/2inch)

Hardenedwasher(5/16inch)

Flangenut(5/16inch)

Carriagebolt(3/8x1-3/4inches)

Flangenut(3/8inch)

Installthebasketrod.

Groomerrod

Bolt(M10x1-1/2inch)

Washer2

Installthegroomerrodkit(forunitswith

groomers;orderedseparately).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3397-826*A

Summary of content (8 pages)

PAGE 1
Form No. 3397-826 Rev A Flexible Grass Basket Kit or Extended Flexible Grass Basket Kit Reelmaster® 3550 Series 18-inch Cutting Unit Model No. 03923 Model No. 03924 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Note: Determine the left and right sides of the machine from the normal operating position.
PAGE 2
Procedure 7 8 Description Use Qty. Basket assembly 1 Install the basket to a cutting unit. No parts required – Adjust the basket position. Kit name Toro part no.
PAGE 3
. Mount a basket guide to the appropriate side of the carrier frame of each cutting unit (Figure 1) with a bolt (5/16 x 1/2 inch) and a flat washer (3/8 x 7/8 inch). Note: The gold torsion spring is for the left side of the carrier frame, and the black spring is for the right side of the carrier frame. Note: Position the components as shown in Figure 2.
PAGE 4
Figure 5 1. Washer (previously removed) 4. Carrier frame 2. Spacer 5. Flange locknut (3/8 inch) Figure 6 3. Bolt (3/8 x 1-1/4 inches) 3 4 Bolt (1/4 x 1-3/4 inches) 4 Locknut (1/4 inch) 2. Bolt, 1/4 x 1-3/4 inches (4) 5. Grass shield 3. Cutoff bar 6. Flange-head bolt, existing (3) Removing the Grass Deflectors Parts needed for this procedure: Cutoff bar 4. Deflector (4) 4 Installing the Cutoff Bar 1 1. Locknut, 1/4 inch (4) If Installed No Parts Required Procedure Procedure 1.
PAGE 5
Installing the Basket Rod Cutting Units Without Groomers Only Parts needed for this procedure: 1 Basket rod 2 Basket plate 2 Flange screw (5/16 x 1/2 inch) 1 Hardened washer (5/16 inch) 1. Flange nut (5/16 inch) 4. Basket rod 1 Flange nut (5/16 inch) 2. Hardened washer (5/16 inch) 5. Non-threaded end 2 Carriage bolt (3/8 x 1-3/4 inches) 3. Threaded end 2 Flange nut (3/8 inch) Figure 8 3. Align the threaded end of the basket rod (Figure 8) with the hole in the other basket plate.
PAGE 6
Figure 10 1. Basket mounting pin 2. Basket guide 3. Basket bracket Figure 9 1. Existing carriage bolt (2) 4. Bolt, M10 x 1-1/2 inches (2) 2. Existing flange nut (2) 5. Groomer rod Installing the Basket to a Rear Cutting Unit 3. Washer (2) Note: You can use the standard baskets (Model 03923) on the front and rear cutting units. You can use the extended baskets (Model 03924) on the front cutting units only. 7 1.
PAGE 7
• On each side of the basket, loosen the nuts on the carriage bolts securing the basket-stop brackets to the basket (Figure 12). • Position the basket so that it is parallel to the cutting unit with a minimum clearance of 6 mm (1/4 inch) between the lip of the basket and the reel (Figure 12). • On each side of the basket, adjust the basket-stop brackets so that they each contact a carrier-frame arm. • Tighten the nuts on the carriage bolts to secure the basket position. Figure 12 Figure 11 1.
PAGE 8