Form No. 3359-317 Rev D Greensmaster® 1000 and 1600 Walk-Behind Mower Model No. 04052—Serial No. 280000001 and Up Model No. 04060—Serial No. 280000001 and Up Register at www.Toro.com.
Warning CALIFORNIA Proposition 65 Warning The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. This spark ignition system complies with Canadian ICES-002. Introduction Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely. You may contact Toro directly at www.Toro.
Contents Leveling the Rear Drum to the Reel ..................... 29 Adjusting the Bedknife to the Reel ...................... 30 Adjusting the Height of Cut ................................ 30 Adjusting the Grass Shield Height....................... 31 Adjusting the Cut-Off Bar .................................. 32 Bedbar Identification.......................................... 32 Setting the Machine to Match Turf Conditions ..................................................... 33 Servicing the Bedbar....
Safety • Warning—Fuel is highly flammable. Take the following precautions: This machine meets or exceeds CEN standard EN 836:1997, ISO standard 5395:1990, and ANSI B71.4-2004 specifications in effect at the time of production when the Operator Presence Kit, Part No. 105–5363 is installed. – Store fuel in containers specifically designed for this purpose. – Refuel outdoors only and do not smoke while refuelling. – Add fuel before starting the engine.
• Keep all parts in good working condition and all hardware and hydraulic fittings tightened. Replace all worn or damaged parts and decals. • If the fuel tank has to be drained, do this outdoors. • Be careful during adjustment of the machine to prevent entrapment of the fingers between moving blades and fixed parts of the machine. • Disengage drives, disengage the cutting unit, set parking brake, stop engine and disconnect spark plug wire.
Vibration (Model 04052) – Reduce speed when making sharp turns. Avoid sudden stops and starts. – When near or crossing roads, always yield the right-of-way. – Apply the service brakes when going downhill to keep forward speed slow and to maintain control of the machine. • The grass basket must be in place during the mowing operation for maximum safety. Shut the engine off before emptying the basket.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 93-9356 1. Entanglement hazard—stay away from moving parts. 93-7348 1. Warning—read the Operator’s Manual. 2. Fire hazard—no fire, open flames, or smoking; when adding fuel to the tank, leave space between the fuel and the top of the tank. 3. Thrown object hazard—keep bystanders a safe distance from the machine. 4.
93-9886 1. Use unleaded gasoline. 93-6085 1. Fast 2. Continuous variable setting 3. Slow 93-8064 1. Warning—read the instructions before servicing or performing maintenance. 2. Cutting hazard of hand or foot—stop the engine and wait for moving parts to stop. 112-9408 1. Engine—stop 2. Engine—run 115-1614 1. Warning—read the Operator’s Manual. 3. Thrown object hazard—keep bystanders a safe distance from the machine. 4. Warning—stay away from moving parts; keep all guards in place. 2.
115-1720 1. Forward 2. Drive wheel 3. Neutral 104-2618 1. Disengage-lever position 2. Parking brake 3.
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 Description Use Qty. Handle Cable tie Kickstand assembly Spring Wheel shaft, right Wheel shaft, left Transport wheels (obtain separately) 1 2 1 1 1 1 2 No parts required – Adjust the cutting unit. Grass basket 1 Install the grass basket. Install the handle. Install the kickstand (model 04035 only). Install the transport wheels. Media and Additional Parts Description Use Qty.
2. While supporting the handle, remove the ring pins from each side and raise or lower the handle to the desired operating position (Figure 2). 5. Squeeze the handle ends inward and install them on the mounting pins (Figure 3). 3. Install the ring pins and hairpin cotters. 2 Installing the Kickstand (Model 04060 Only) Parts needed for this procedure: Figure 3 1. Handle end 6. Secure the handle ends to the mounting pins with the bolts, washers, and lockwashers previously removed (Figure 3).
3 Installing the Transport Wheels Parts needed for this procedure: 1 Wheel shaft, right 1 Wheel shaft, left 2 Transport wheels (obtain separately) Procedure 1. Push the kick stand down with your foot and pull up on the handle to support the mower on the kick stand. Figure 7 1. Locking clip 2. Apply #242 Loctite to the threads of the wheel shafts. 7. Rotate wheel back and forth until it slides completely onto axle and locking clip is secured in groove on axle shaft. 3.
Product Overview 5 Controls Installing the Grass Basket Parts needed for this procedure: 1 Grass basket Procedure Grasp basket by top lip and slide it onto the basket mounting rods (Figure 8). Figure 9 1. Traction drive lever 2. Throttle control 3. On/off switch 4. Service/parking brake Throttle Control The throttle control (Figure 9) is located on rear right side of the control panel. The lever connects to and operates throttle linkage to the carburetor.
Reel Drive Lever The reel drive lever (Figure 10) is located on the right front corner of the machine. The lever has two positions: Engage and Disengage. Pull up on the lever to engage the reel or push it down to disengage the reel. Figure 12 1. Recoil starter 2. Kick stand Kickstand The kickstand (Figure 12) is mounted to the rear of machine and is used to raise the rear of machine for installation or removal of the transport wheels. Figure 10 1.
Operation Note: Determine the left and right sides of the machine from the normal operating position. In certain conditions, gasoline is extremely flammable and highly explosive. A fire or explosion from gasoline can burn you and others and can damage property. Think Safety First • Fill the fuel tank outdoors, in an open area, when the engine is cold. Wipe up any gasoline that spills. Please carefully read all of the safety instructions and decals in the safety section.
In certain conditions during fueling, static electricity can be released causing a spark which can ignite the gasoline vapors. A fire or explosion from gasoline can burn you and others and can damage property. • Always place gasoline containers on the ground away from your vehicle before filling. • Do not fill gasoline containers inside a vehicle or on a truck or trailer bed because interior carpets or plastic truck bed liners may insulate the container and slow the loss of any static charge.
Checking the Interlock Switch Operation out because rope may break or recoil assembly may be damaged. 7. Move the choke to the Off position as the engine warms up. Service Interval: Before each use or daily Stopping the Engine 1. Move the traction and reel drive controls to the Disengaged position, the throttle control to the Slow position, and the On/Off switch to the Off position. 2.
for fundamental suggestions to obtain the utmost performance from your mower. Important: Excessive operation of the cutting unit with the absence of grass clippings (lubricant) can damage the cutting unit. 1. Start the engine, set the throttle at reduced speed, push down on the handle to raise the cutting unit, move the traction lever to the Engaged position, and transport the mower onto collar of the green. 2.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 8 hours • Change the engine oil. After the first 25 hours • Clean the fuel filter. Before each use or daily • Check the interlock switch operation. • Check the engine oil level. Every 25 hours • Grease the machine. • Clean and oil the air cleaner foam element.
Daily Maintenance Checklist Important: Duplicate this page for routine use. Maintenance Check Item For the week of: Mon. Tues. Wed. Thurs. Fri. Check the safety interlock operation. Check the parking brake operation. Check the fuel level. Check the engine oil level. Check the air filter. Clean the engine cooling fins. Check for unusual engine noises. Check for unusual operating noises. Check the reel-to-bedknife adjustment. Check the height-of-cut adjustment. Grease all fittings.
Lubrication Greasing the Machine Service Interval: Every 25 hours Lubricate the 13 grease fittings on the mower using a No. 2 multipurpose lithium base grease. A hand operated grease gun is recommended for best results. The grease fitting locations are as follows: Figure 16 • 2 on the front roller (Figure 14) • 2 on the reel bearings (Figure 14) • 2 on the drum axles (Figure 15) • 3 on the differential (Figure 15) • 2 on the reel countershaft bearings (Figure 16) • 2 on the belt idler pivots (Figure 17).
Engine Maintenance Servicing the Engine Oil Service Interval: After the first 8 hours—Change the engine oil. Before each use or daily—Check the engine oil level. Every 50 hours—Change the engine oil. (More frequently in dusty or dirty conditions) The crankcase must be filled with approximately 20 fluid ounces of proper viscosity oil before staring. The engine uses any high-quality oil having the American Petroleum Institute - APl - “service classification" SF, SG, SH or SJ.
4. Push down on the handle to tip the mower and the engine backward, allowing more oil to run into the drain pan. 5. Install the drain plug and refill the crankcase with the proper oil; refer to Checking the Engine Oil Level. Servicing the Air Cleaner Service Interval: Every 25 hours—Clean and oil the air cleaner foam element. (More often in dirty or dusty conditions) Every 100 hours—Clean or replace the paper air filter element.
Fuel System Maintenance 3. Set the air gap at 0.028 to 0.032 inch (0.05 to 0.07 cm) (Figure 24). Cleaning the Fuel Filter Service Interval: After the first 25 hours Every 50 hours 1. Close the fuel shut off valve and unscrew the bowl from the filter body (Figure 25). Figure 24 4. Install the correctly gapped spark plug and tighten it to 17 ft.-lb (23 N-m). 5. Install the spark plug wire on the spark plug. Figure 25 1. Shut-off valve 2. Bowl 2.
Brake Maintenance Electrical System Maintenance Servicing the Interlock Switch Adjusting the Service/Parking Brake Use the following procedure if the switch needs adjustment or replacement. If service/parking brake slips when operated, an adjustment is required. 1. Make sure the engine is off and the traction lever is disengaged and resting against the neutral stop (Figure 26). 1. Move service/parking brake lever to the Off position. 2.
Belt Maintenance Important: Do not over tension the belt. B. Tighten the nut to lock the adjustment. Adjusting the Belts 4. Install the belt cover by placing it in position. Service Interval: Every 300 hours—Check the condition and tension of belts. 5. While maintaining a slight gap between the cover seal and the side plate, install each mounting bolt until the threads engage in the insert. The gap allows visual alignment of the bolts to the threaded inserts.
Adjusting the Primary V-Belts the belt until the desired belt tension is attained (Figure 31). 1. To adjust the belt tension on primary V-belts, first check the adjustment of the traction control. Refer to Adjusting the Traction Control. If unable to attain the 4 to 5 lb force required in adjusting the traction control, proceed to next step. Important: Do not over tension the belt. B. Tighten the nut to lock the adjustment. 4. Install the belt cover by placing it in position. 5.
Figure 34 1. Primary V-belts 2. Belt guide Figure 35 3. Idler pulley 1. Differential cover sections 2. Front clutch housing 7. Tighten the mounting screws and check the alignment. 3. Right rear bearing housing 5. Loosen the idler pulley mounting nut on the differential idler pulley and pivot the idler pulley counterclockwise away from the backside of the belt to release the belt tension. 8.
Controls System Maintenance Cutting Unit Maintenance Leveling the Rear Drum to the Reel Adjusting the Traction Control 1. Position the machine on a flat, level surface, preferably a precision steel work plate. If traction control does not engage or it slips during operation, an adjustment is required. 2. Place a 1/4 x 1 inch (0.6 x 2.5 cm) flat steel strip, approximately 29 inches (73.
turn the bedbar adjusting screw clockwise (on the same end of reel, one click at a time, until the paper is pinched lightly, when inserted from the front, parallel to the bedknife, which results in a slight drag when paper is pulled ( Figure 39) Figure 38 1. Driven pulley 2. 4 holes 3. Idler Pulley 8. Loosen the 4 roller bearing screws and the screw securing the idler pulley. Figure 40 9. Raise or lower the right side of the roller assembly until the gap is less than 0.010 inch (.025 cm).
Important: When set properly, the rear and front rollers will contact the gauge bar and the screw will be snug against the bedknife. This ensures the height-of-cut is identical at both ends of the bedknife. 7. Tighten nuts to lock the adjustment. Important: To avoid scalping on undulating turf, ensure that the roller supports are positioned rearward (the roller closer to the reel). Note: The front roller can be put in three different positions (Figure 44), depending on the application and needs of the user.
Bedbar Identification cm). Loosen the bolts and nuts securing each end of the shield to the sideplate and adjust the shield to the correct height. To determine if the bedbar is standard or aggressive, check the left bedbar mounting ears. If the mounting ears are rounded it is a standard bedbar. If the mounting ears have a notch in them, it is an aggressive bedbar (Figure 47). 3. Tighten the fasteners.
Setting the Machine to Match Turf Conditions Use the following table to set the machine to match turf conditions.
Servicing the Bedbar 5. Tighten the spring tension nut until the spring is collapsed, then back it off 1/2 turn. Removing the Bedbar 6. Adjust the bedbar; refer to Adjusting the Bedknife to the Reel. 1. Turn bedbar adjuster screw, counterclockwise, to back bedknife away from reel (Figure 48). Backlapping the Reel 1. Remove the plug in the right reel drive cover (Figure 50). Figure 48 1. Bedbar adjusting screw 2. Spring tension nut 3. Bedbar 2.
Storage 1. Remove grass clippings, dirt, and grime from the external parts of the entire machine, especially the engine. Clean dirt and chaff from the outside of the engine’s cylinder head fins and blower housing. Important: You can wash the machine with mild detergent and water. Do not pressure wash the machine. Avoid excessive use of water, especially near the shift lever plate, and engine. 2. For long-term storage (more than 90 days) add stabilizer/conditioner additive to fuel in the tank. A.
Toro General Commercial Products Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial Product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
