Installation Instructions

ManualsBrandsToro ManualsAttachmentsDethatcher Kit, Greensmaster 1000

FormNo.3391-569RevA

DethatcherKit

Greensmaster

1000

ModelNo.04109

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

ThisproductcomplieswithallrelevantEuropeandirectives.

Fordetails,pleaseseetheDeclarationofIncorporation(DOI)

atthebackofthispublication.

RemovingtheBedbar

1.Positionthemoweronaat,levelworksurfaceand

ensuretheengineisoff.

2.Removethehightensionleadfromthesparkplug.

3.Removethebedbarfromthemower.Refertoyour

Operator’sManualforremovalinstructions.

Note:Bedbaradjustersmayalsoberemovedfrom

themowersideplates.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3391-569*A

Summary of content (8 pages)

PAGE 1
Form No. 3391-569 Rev A Dethatcher Kit Greensmaster® 1000 Model No. 04109 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. This product complies with all relevant European directives. For details, please see the Declaration of Incorporation (DOI) at the back of this publication. Removing the Bedbar 1.
PAGE 2
Removing the Reel 4 1. Remove 4 cap screws, 4 lock washers, and the reel drive cover from the mower (Figure 1). 2 8 10 1 2 7 5 3 5 6 9 16 4 17 FRONT 11 7 RIGHT LEFT 12 9 6 3 13 FRONT 15 G028281 Figure 2 10 1 8 G028280 14 Figure 1 1. Grease fitting 10. Cover standoff 2. Capscrew 11. Right-hand bearing housing 3. Lock washer 4. Reel drive cover 12. Frame 13. Large seal 16. Bearing 8. Nut 9. Groomer arm cover 17. Wave washer 6. Bearing locknut 2. Left bearing housing 7.
PAGE 3
Installing the New Grass Shield 1. Remove the fasteners securing the grass shield to the mounting brackets and remove the shield. 1 3 2 4 5 G028282 Figure 3 1. Shield 4. Spacer-seal 2. Shield bracket 5. Height-of-cut arm 3. Dethatcher assembly Installing the Dethatcher Reel 2. Loosely mount a shield bracket to each end of the new grass shield with a 5/8 inch capscrew, flat washer, and lock nut as shown in Figure 3. 1. Position the reel in the frame to accept the bearing housings. 3.
PAGE 4
Installing the New Height-of-Cut Arms (Model 04052 and 04055) 4. Attach the left-hand bearing housing through the frame onto the reel shaft (Figure 2). A. Push the housing onto the reel shaft. Note: If necessary, tap it into position with a soft hammer. B. Make sure the grease fitting hole is positioned to the front of the mower. C. Align the housing holes to the frame holes with both cap screws and lock nuts. 1.
PAGE 5
Maintenance Removing the Blades from the Shaft 1. Remove 1 of the 1–1/8 inch nuts from the shaft. 2. Disassemble the spacers and the dethatching blades from the shaft. Note: When disassembling the blades from hex shaft, pay close attention to the position of the index holes in the blades. This is very important for the later assembly of the blades. Figure 5 CAUTION 1.
PAGE 6
Reversing Dull Blades (Optional Blades Only) When the optional dethatcher blades become dull, grinding is not required to sharpen them. The optional dethatcher blades can be disassembled from the reel, reversed 180° and reassembled. Grinding the blades is only required when both sides of the reel have become dull or rounded. Assemble the dethatcher blades by inverting all of them 180° and following the steps in Installing the Optional Dethatcher Blades (page 5).
PAGE 7
Declaration of Incorporation Model No. 04109 Serial No. Product Description Invoice Description General Description Directive — Dethatcher Kit, Greensmaster 1000 DETHATCHING KIT DYNABLADE GR 1000 Dethatching Kit 2006/42/EC Relevant technical documentation has been compiled as required per Part B of Annex VII of 2006/42/EC. We will undertake to transmit, in response to requests by national authorities, relevant information on this partly completed machinery.
PAGE 8