Installation Instructions

ManualsBrandsToro ManualsAttachmentsOut-Front Brush Kit, Greensmaster 1018, 1021, or 1026 Series Mower

FormNo.3440-278RevB

Out-FrontBrushKit

Greensmaster

1018,1021,or1026SeriesMower

ModelNo.04136

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Leftbrushbracket

Rightbrushbracket1

Hex-socket-headscrew(5/16x1inch)

Flangelocknut(5/16)

Spacernut

Rubberbumper2

Jamnut2

Leveladjustmentscrew2

Locknut(5/16inch)

Locknut(1/4inch)

Leftbrushrod

Rightbrushrod1

Mountthebrushbrackets(xed-headmachinesonly).

Leftbrushbracket

Rightbrushbracket1

Hex-socket-headscrew(5/16x1inch)

Flangelocknut(5/16)

Spacernut

Rubberbumper2

Jamnut2

Leveladjustmentscrew2

Locknut(1/4inch)

Leftbrushrod

Rightbrushrod1

Bolt(5/16x3/4inch)

Mountthebrushbrackets(Flexmachinesonly).

Brush1

Brushtab2

Lagscrew(5/16x1-1/2inches)

Flange-headbolt(1/4x3/4inches)

Flangelocknut(1/4inch)

Mountthebrush.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3440-278*

Summary of content (4 pages)

PAGE 1
Form No. 3440-278 Rev B Out-Front Brush Kit Greensmaster® 1018, 1021, or 1026 Series Mower Model No. 04136 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped.
PAGE 2
Preparing the Machine 1. Park the machine on a level surface. 2. Engage the parking brake. 3. Shut off the machine. 4. Remove the cutting unit from the machine; refer to your machine Operator’s Manual. Mounting the Brush Brackets Fixed-Head Machines Only 1. If the cutting unit is attached to the traction unit, position the traction unit on a level surface, engage the parking brake, shut off the traction unit, remove the key (if equipped), and disconnect the battery. 2.
PAGE 3
g325175 Figure 4 Left side shown 3. Install the bolts here. 1. Left brush bracket 2. Bolt (5/16 x 3/4 inch) 3. Install a rubber bumper to both brush brackets with a locknut (1/4 inch) as shown in Figure 5. 4. Install a level adjustment screw to both brush brackets as shown in Figure 5. g325189 Figure 3 1. Spacer nut 3. Hex-socket-head screw (5/16 x 1 inch) 2. Brush rod Mounting the Brush Brackets Flex machines only 1.
PAGE 4
. With the brush in the operating position on level ground, adjust both level-adjustment screws from 0.6 cm (1/4 inch) to 1.3 cm (1/2 inch) below the brush rods. Tighten the jam nuts. Adjust as needed to maintain desired ground contact. Note: The ends of the brush bristles should be flat on the ground during the mowing operation. If the brush hops during operation, rotate the brush so that only the front bristles touch the surface and the rear bristles are less than 1.3 cm (1/2 inch) above the surface.