Form No. 3415-600 Rev B Transport Frame TransPro™ 80 Tow-Behind Trailer Model No. 04238—Serial No. 230000801 and Up Model No. 04244 Model No. 04245 Model No. 04247 Installation Instructions Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal98-8687 98-8687 1. The trailer tires should be inflated to 0.35 bar (5 psi); read the Operator’s Manual.
Installation Mounting the Axle and Ramp (Model 04245) or Rail (Models 04244 and 04247) Assemblies The Transpro 80 is intended for use with Greensmaster 800, 1000, 1010, 1600, 1610, 2000, 2600, as well as Flex 18, 21, 1800, 1820, 2100, 2120 and eFlex 1800, 1820, 2100, 2120 Walk Greensmasters. 1. Mounting the Tongue Assembly 1. Insert the tongue assembly into the frame assembly while aligning the rear mounting holes (Figure 1). 2.
Mounting the Wheel Assemblies 1. Mount a wheel assembly to each axle hub with 4 lug nuts (Figure 5). Tighten the nuts to 108 N⋅m (80 ft-lbs). 2. Adjust the tire pressure to 5 psi (34 kPa). g014665 Figure 5 g215364 Figure 3 1. Axle assembly 4. Washer 2. Right ramp assembly 5. Nut 1. Axle 2. Wheel assembly Important: Higher tire pressure may 3. Bolt (3/8 x 3 inches) damage the machine.
Mounting the Greensmower Wheel Assemblies Using one of the configurations shown in Figure 7 or Figure 8, adjust and secure the hitch straps to the trailer tongue. (Models 04244 and 04247 only) Note: On the Greensmaster 1000, 1010, and 2000 when equipped with a groomer, you must remove the wheel shaft on the groomer end and purchase and install a new wheel shaft (Part No. 106–5385). Also, you must mount the rail assembly on the groomer end to Greensmaster 1600 and 1610 hole locations (Figure 2).
3. Loading the Trailer Insert a wheel onto each shaft and secure with a wheel clip (Figure 10). 1. Note: The Flex 1800, 1820, and 2100, 2120 series requires a different wheel offset than all other Toro Greensmowers. Read and follow the mounting instructions molded into the sides of the wheels. While maintaining control of the trailer bed and holding onto the handle, press down on the latch assembly and the lift handle (Figure 11). Lower the trailer bed to the ground.
• On flat ramps, rotate the wheel rods downward over the greens mower transport wheels (Figure 13). • On rail ramps, lift the wheel rod and rotate it behind the greens mower transport wheels (Figure 14). g014672 Figure 14 1. Wheel rod (shown in the closed position) g214902 7. Push down on the handle until the trailer assembly locks into the latch assembly (Figure 11). 8. For Flex GreensMaster machines, secure the front of the machine by hooking the bungee straps to the basket hoop.
Operation • Always slow the tow vehicle gradually when Operating Tips • When turning or driving on slopes, always 1. 2. 3. 4. changing direction of travel or preparing to stop. slow the tow vehicle, then turn to prevent loss of control and possible upset. The Transpro 80 is intended for use with Greensmaster 800, 1000, 1600, 2000, 2600, Flex 18, 21, 1800, 1820, 2100, 2120 and eFlex 1800, 1820, 2100, 2120 Walk Greensmasters.
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 10 hours • Check the torque of the wheel lug nuts. • Service the wheel hub and inspect for damage. • Lubricate the wheel hub assembly. Yearly Servicing the Wheel Hub Lubricating the Wheel Hub Assembly Service Interval: Yearly Service Interval: Yearly 1. Raise the trailer on jack stands. 2. Remove the 4 lug nuts securing the wheel to the wheel hub and remove the wheel. 3.
Checking the Torque of the Wheel Lug Nuts Service Interval: After the first 10 hours Check the torque of the wheel lug nuts each time you install the wheels and after the first 10 hours of operation. WARNING Failure to maintain proper torque could result in failure or loss of wheel and could result in personal injury. Torque wheel lug nuts to 108 N⋅⋅m (80 ft-lbs).
Notes:
Notes: