Form No. 3385-370 Rev C 11 and 14-Blade Cutting Unit Greensmaster® Flex™/eFlex® 1800/2100 Traction Units Model No. Model No. Model No. Model No. Register at www.Toro.com. Original Instructions (EN) 04251—Serial No. 04252—Serial No. 04253—Serial No. 04254—Serial No.
This manual identifies potential hazards and has safety messages identified by the safety-alert symbol (Figure 2), which signals a hazard that may cause serious injury or death if you do not follow the recommended precautions. WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. g000502 Figure 2 1. Safety alert symbol This manual uses 2 words to highlight information.
Safety hearing protection. Tie back long hair and do not wear jewelry. • Remove all debris or other objects that the Hazard control and accident prevention are dependent upon the awareness, concern, and proper training of the personnel involved in the operation, transport, maintenance, and storage of the machine. Improper use or maintenance of the machine can result in injury or death. To reduce the potential for injury or death, comply with the following safety instructions.
Setup Media and Additional Parts Description Use Qty. Operator's Manual 1 Read this before installing and operating cutting unit. Parts catalog 1 Use this to reference part numbers. Certification of compliance 1 Save this for future reference. Target plate Weight bar 1 1 Install these parts if you are using an eFlex traction unit. 1 Installing the Front Roller No Parts Required Procedure The cutting unit is shipped without a front roller.
Note: Ensure that the nuts or back of the adjusting screw counterclockwise moves the bedknife edge away from the reel. bedbar adjusting screws are not resting on the work surface (Figure 3). 3. Rotate the reel so that 1 of the blades crosses the bedknife edge between the first and second bedknife screw heads located on the right side of the cutting unit. 4. Make and identifying mark on the blade where it crosses the bedknife edge. 11.
4 Adjusting the Rear Roller No Parts Required 2. Remove the 2 nuts securing each roller bracket and spacer to each sideplate mounting flange. 3. Lower the roller and screws from the sideplate mounting flanges and spacers. 4. Place the spacers onto the screws above of below the roller brackets, as required (Figure 6 or Figure 7). 5. Secure the roller bracket and spacers to the underside of the mounting flanges with the nuts previously removed. 6. Verify that the bedknife to reel contact is correct.
5 Adjusting the Height of Cut No Parts Required Procedure Note: This cutting unit comes standard with the Edgemax Micro-cut bedknife and standard bedbar. The effective height of cut is dependent on previous mower configurations and turf conditions (i.e., roller type, bedknife behind center distance, soft or firm greens, season conditions). Set initial height-of-cut to 0.25 mm to 0.38 mm (0.010 to 0.015 inch) higher than previous setup and adjust to match conditions. g014407 Figure 9 3.
6 Adjusting the Cut-off Bar No Parts Required Procedure g016945 Figure 11 Adjust the cut-off bar to ensure that the clippings are cleanly discharged from the reel area as follows. 1. Gauge bar 4. Rotate the adjusting screw until the roller contacts the front of the gauge bar. 5. Adjust both ends of the roller until the entire roller is parallel to the bedknife. 1. Loosen the screws securing the top bar (Figure 12) to the cutting unit.
7 Preparing the Cutting Unit for Use on an eFlex Machine Parts needed for this procedure: 1 Target plate 1 Weight rod (supplied with your traction unit) 1 Flange-head bolt (supplied with your traction unit) Installing the Target Plate • If you will be using the cutting unit on an eFlex traction unit, install the provided target plate, then adjust the machine sensors as described in the eFlex traction unit Operator’s Manual. g017294 Figure 13 • If you will be using the cutting unit on 1.
4. Secure the threaded end of the weight rod to the frame using a flange-head bolt (Figure 15). g026124 Figure 15 1. Flange-head bolt 2.
Product Overview Specifications Tractors These cutting units mount on the appropriate size Flex and eFlex Traction Units. Height-of-cut The cutting height is adjusted on the front roller by 2 vertical screws and held by 2 locking cap screws Height-of-cut range Standard bench height of cut range is 1.6 mm (0.062 inch) to 12.7 mm (0.500 inch). The bench height-of-cut range with the High Height of Cut Kit installed is 7 mm (0.285 inch) to 25 mm (1.00 inch).
Operation impact on energy consumption. Very light contact is recommended for optimum cutting performance and battery consumption. Note: Determine the left and right sides of the machine from the normal operating position. Note: As the reel blades continue to run against the bedknife, a slight burr will appear on the front cutting edge surface along the full length of the bedknife. If you occasionally run a file across the front edge to remove this burr, this will improve the cutting performance.
g017116 Figure 17 1. Bearing-housing nut 3. Compression spring 2. Reel drive belt 4. Using a 16 mm (5/8 inch) wrench, rotate the bearing housing to make sure it operates freely. 5. Remove the belt (Figure 17). 6. Using the chart shown on the decal in Figure 18, determine the clip setting you want and which pulleys you will need to move. Note: Each pulley is numbered (22, 24, and 25). Move the pulleys to the positions indicated in the chart for your clip setting. decal131-1820 Figure 18 7.
Maintenance 4. Note: Determine the left and right sides of the machine from the normal operating position. Remove each bedbar bolt allowing the bedbar to be pulled downward and removed from the machine bolt (Figure 20). Account for the 2 nylon and 2 stamped steel washers on each end of the bedbar (Figure 21). Servicing the Bedbar Removing the Bedbar 1. Turn the bedbar-adjusting screw, counterclockwise, to back the bedknife away from the reel (Figure 19). g016970 Figure 21 1. Bedbar bolt 2.
Sharpening Reel and Rotary Mowers Manual (Form No. 80-300PT). Note: For a better cutting edge, run a file across the front face of the bedknife when the lapping operation is completed. This removes any burrs or rough edges that may have built up on the cutting edge. A very light file touch may be necessary on the top edge to break the burr off completely from the cutting edge.
Notes:
Notes:
Notes:
Declaration of Incorporation The Toro Company, 8111 Lyndale Ave. South, Bloomington, MN, USA declares that the following unit(s) conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain Toro models as indicated on the relevant Declarations of Conformity. Model No. Serial No.
The Toro Total Coverage Guarantee A Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
