Installation Instructions

ManualsBrandsToro ManualsAttachmentsOut-Front Brush Kit, Greensmaster 800/1000/Flex 18/21/Flex 1800/2100/eFlex 1800/2100 Mower

FormNo.3427-206RevA

Out-FrontBrushKit

Greensmaster

800/1000/Flex

™

18/21/Flex

™

1800/2100/eFlex

1800/2100Mower

ModelNo.04266

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Leftbrushbracket

Rightbrushbracket1

Flangeheadbolt(3/8x1inch)

Bolt(M10x30mm)

Leveladjustmentscrew2

Jamnut(5/16inch)

Locknut(5/16inch)

Brushspring2

Brushrod2

Bolt(M6x40mm)

Spacer

Locknut(M6)

Mountthebrushbrackets(GreensmasterFlexmodels

only)

Leftbrushbracket

Rightbrushbracket1

Bolts(fullythreaded,5/16x1-1/2inches)

Locknut(5/16inch)

Leveladjustmentscrew2

Jamnut(5/16inch)

Locknut(5/16inch)

Brushspring2

Brushrod2

Bolt(M6x40mm)

Spacer

Locknut(M6)

Mountthebrushbrackets(Greensmaster800/1000/2000

modelsonly)

Brush1

Brushtab2

Bolt(M8x60mm)

Washer4

Locknut(M8)

Flange-headbolt(M6x20mm)

Flangenut(M6)

Mountthebrush.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3427-206*A

Summary of content (4 pages)

PAGE 1
Form No. 3427-206 Rev A Out-Front Brush Kit Greensmaster® 800/1000/Flex™ 18/21/Flex™ 1800/2100/eFlex® 1800/2100 Mower Model No. 04266 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped.
PAGE 2
Mounting the Brush Brackets Greensmaster Flex Models only 1. Position the machine on a level surface, engage the parking brake, remove the key (if equipped), disconnect the battery, and shut off the machine. 2. Remove the bolt and washer securing the left end of the front frame to the tab on top of the cutting unit (Figure 1). g018486 Figure 2 1. Bolt and washer (Flex 18/21 models) 4. Jam nut (5/16 inch) 2. Flange head bolt (Flex 1800/2100 models) 5. Brush bracket 3. Level adjustment screw 6.
PAGE 3
g017161 Figure 3 1. Locknut (M6) 2. Brush rod 4. Brush spring g017162 Figure 4 5. Bolt (M6 x 40 mm) 3. Spacer 6. 1. Bolt 3. Grass basket mounting rod 2. Washer Repeat this procedure on the opposite side of the machine. Note: There will be leftover locknuts. Mounting the Brush Brackets Greensmaster 800/1000/2000 Models 3. Secure the grass basket mounting rod to the left side plate with 2 new, fully threaded bolts (5/16 x 1-1/2 inches) and the 2 washers that were previously removed (Figure 5).
PAGE 4
5. Loosely mount the level adjustment screw to the brush bracket with a jam nut (5/16 inch) and a locknut (5/16 inch) as shown in Figure 5. 6. Mount a brush spring and brush rod to the brush bracket with 2 bolts (M6 x 40 mm), spacers, and locknuts (M6) as shown in Figure 6. Note: Ensure that the brush spring is mounted with the bump to the outside. The brush rod should be centered in the brush spring when it is rotated upward, into the storage position. g017165 Figure 7 1. Brush weight (optional) 6.