Installation Instructions

ManualsBrandsToro ManualsAttachmentsLED Light Kit, Greensmaster Flex 1800/2100 Series and eFlex 1800/2100 Series Mower

FormNo.3399-947RevC

LEDLightKit

Greensmaster

Flex

™

1800/2100SeriesandeFlex

1800/2100

SeriesMower

ModelNo.04293

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Important:IfyouareinstallingtheLEDLightKitonGreensmasterModels04040,04041,04044,and04045,ensure

thatyouhaveinstalledtheLEDLightandWirelessHourMeterHarnessKitfor2012andAfter(Model04295)

beforeyouinstalltheLEDlightkit.

Note:Determinetheleft,right,front,andbacksidesofthemachinefromthenormaloperatingposition.

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Nopartsrequired

–

Removethecontrol-panelcover.

Leftlight-barstrap

Flange-headbolt(5/16x1-1/4inches)

Flangelocknuts(5/16inch)

Flange-headbolt(5/16x1inch)

Washer(5/16inch)

Rightlight-barstrap1

Cabletie

Assemblethelightbartothemachine.

Nopartsrequired

–

AssembletheLEDlightstothelightbar.

Cabletie

3Installthewireharnesstothemachine.

2-positionrockerswitch1

Installthelightswitch(machinemodels

04042,04043,04046,and04047).

Nopartsrequired

–

Finishthelightkitinstallation.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3399-947*C

Summary of content (12 pages)

PAGE 1
Form No. 3399-947 Rev C LED Light Kit Greensmaster® Flex™ 1800/2100 Series and eFlex® 1800/2100 Series Mower Model No. 04293 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
PAGE 2
Disconnecting the Battery 1 eFlex 1800 and 2100 Series Machines 1. Ensure the traction and reel drive engagement lever is in the REEL-DRIVE OFF position. Preparing the Machine 2. Move the machine to a level surface and set the traction and reel drive engagement lever to the TRACTION -DRIVE NEUTRAL position. No Parts Required 3. Rotate the key switch to the OFF position. Disconnecting the Spark-Plug Wire 4. Wait 10 to 15 minutes for the motor capacitors to discharge.
PAGE 3
2 3 Removing the Control-Panel Cover Assembling the Light Bar to the Machine No Parts Required Parts needed for this procedure: Procedure 1. Remove the 4 flange-head screws (1/4 x 1/2 inch) that secure the control-panel cover to the support bracket of the handle bar (Figure 3).
PAGE 4
3. Align the 2 holes in the right light-bar strap with the 2 holes 9.5 mm (3/8 inch) holes in the right side plate (Figure 5). Figure 5 Engine model shown; the electrical models are similar. 1. Front of the machine 4. Right light-bar strap 2. Flange locknut (3/8 inch) 5. Flange-head bolt (3/8 x 1-1/4 inches) 3. Hole (right side plate) 4. Assemble the right light-bar strap to the right side plate (Figure 5) with the 2 flange-head bolts (3/8 x 1-1/4 inches) and 2 flange locknuts (3/8 inch).
PAGE 5
4 Assembling the LED Lights to the Light Bar No Parts Required Assembling the Wire Harness to the LED Light Fixtures 1. Connect the 2-pin of the LED light into the 2-socket connector of the LED light harness (Figure 7). Note: Ensure that the connectors are fully seated and the latch of the connectors snap together securely. Figure 8 1. LED light harness 5. Carriage bolt (short) 2. Carriage bolt (long) 6. Mount bracket (LED light) 3. Frame (LED light) 7. Nut 4. Shield 4.
PAGE 6
Assembling the LED Light Fixtures to the Light-Bar Straps 5 1. Align the light fixtures with the lenses of the lights toward the front of the machine (Figure 9). Installing the Wire Harness to the Machine Parts needed for this procedure: 3 Cable tie Routing the Wire Harness 1. Route the wiring harness for the LED light kit down the left light-bar strap and across to the left handle-bar tube (Figure 10). Figure 9 1. Hole (light-bar strap) 5. Cable ties 2. Carriage bolt (short) 6. Nut 3.
PAGE 7
Connecting the Wire Harness to the Wire Harness of the LED Light and Wireless Hour Meter Harness Kit Connecting the Wire Harness to the Wire Harness of the Machine eFlex 1800 and 2100 Series Machines Flex 1800 and 2100 Series Machines 1. Align the 2-socket connect of the wire harness for the machine with the 2-pin connector of the light-kit harness (Figure 12). Note: The 2-position rocker switch with a 10-pin connector is installed in the LED light and wireless hour meter harness kit. 1.
PAGE 8
Figure 14 1. Opening (control panel) 3. Notch (body—rocker switch) 2. Rocker switch 4. Back of the control panel Figure 13 1. Plug 3. 2-position rocker switch 2. Opening (control panel) 4. 10-socket connector (wire harness—LED light and wireless hour meter harness kit) 5. Insert the switch into the opening in the control panel until the switch snaps securely into the panel (Figure 14). 2.
PAGE 9
Connecting the Spark-Plug Wire 7 Flex 1800 and 2100 Series Machines Connect the spark-plug wire to the terminal of the spark plug; refer to Figure 1 of Disconnecting the Spark-Plug Wire (page 2).
PAGE 10
Notes: 10
PAGE 11
Notes: 11
PAGE 12