Installation Instructions

ManualsBrandsToro ManualsAttachmentsLED Light and Wireless Hour Meter Harness Kit, 2012 and After Greensmaster 800, 1000, 1600, Flex 1800, or 2100 Series Mower

FormNo.3401-934RevA

LEDLightandWirelessHourMeterHarnessKit

2012andAfterGreensmaster

800,1000,1600,Flex

™

1800,or

2100SeriesMower

ModelNo.04295

InstallationInstructions

ContactyourAuthorizedToroDistributorformoreinformation.

ThisproductcomplieswithallrelevantEuropeandirectives;fordetails,pleaseseetheseparateproductspecicDeclarationof

Conformity(DOC)sheet.

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Nopartsrequired

–

Removethecontrol-panelcover(1800

or2100seriesmachines).

Flangeheadscrew2

Voltageregulator1

Mountingbracket1

Wireharness1

Assemblethevoltageregulator.

Cabletie

2Routethewireharness.

Rockerswitch1

Connectthewireharness.

Nopartsrequired

–

FinishtheLEDlightandwirelesshour

meterharnesskitinstallation.

Nopartsrequired

–

InstallthewireharnesstotheLEDlight

kitand/orwirelesshourmeterkit.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3401-934*A

Summary of content (12 pages)

PAGE 1
Form No. 3401-934 Rev A LED Light and Wireless Hour Meter Harness Kit 2012 and After Greensmaster® 800, 1000, 1600, Flex™ 1800, or 2100 Series Mower Model No. 04295 Installation Instructions Contact your Authorized Toro Distributor for more information. This product complies with all relevant European directives; for details, please see the separate product specific Declaration of Conformity (DOC) sheet.
PAGE 2
Preparing an 1800 or 2100 Series Machine 1 1. Ensure the traction and reel drive engagement lever is in the REEL-DRIVE OFF position; refer to the Operator’s Manual. Preparing the Machine 2. Move the machine to a level surface and set the traction and reel drive engagement lever to the TRACTION -DRIVE NEUTRAL position; refer to the Operator’s Manual. No Parts Required Preparing an 800, 1000, or 1600 Series Machine 3.
PAGE 3
2 3 Removing the Control-Panel Cover (1800 or 2100 Series Machines) Assembling the Voltage Regulator Parts needed for this procedure: No Parts Required Procedure 1. Remove the 4 flange-head screws (1/4 x 1/2 inch) that secure the control-panel cover to the support bracket of the handle bar (Figure 3). 2 Flange head screw 1 Voltage regulator 1 Mounting bracket 1 Wire harness Assembling the Voltage Regulator, Mounting Bracket, and Wire Harness 1.
PAGE 4
Figure 5 1. 3-pin connector (wire harness) 2. 3-socket connector (voltage regulator) Assembling the Voltage Regulator and Mounting Bracket to the Machine Figure 7 1. Prepare the machine for installation of the voltage regulator and mounting bracket by performing the following: • 800, 1000, or 1600 series machine 1. Cable tie (fir-tree anchor) 4. Stud (fuel tank) 2. Wire-harness bracket 5. Flange-head bolt (10-24 x 3/8 inch) 3. Nut 6. Interlock module A.
PAGE 5
2. Align the ground terminal of the wire harness with the left hole short flange of the mounting bracket for the voltage regulator as shown in Figure 9. 4 Routing the Wire Harness Parts needed for this procedure: 2 Cable tie Procedure 1. Route the wire harness from the mounting bracket to the left handlebar (Figure 10 and Figure 11). Figure 9 1. Ground terminal (wire harness) 3. Nut 2. Stud (fuel tank) 4. Mounting bracket (voltage regulator) 3.
PAGE 6
5 Connecting the Wire Harness Parts needed for this procedure: 1 Rocker switch Connecting the Wire Harness to the Engine 1. Locate the engine-alternator harness at the rear side of the engine case (Figure 12). Figure 11 1800 or 2100 Series Machines 1. Left handlebar 2. Support bracket (handle bar) Note: The engine-alternator harness has 2 wires with single socket connectors. 3. Wire harness 4. Cable ties 2.
PAGE 7
Identifying the Electrical Connectors • Use the 3-socket connector when installing the optional Wireless-Hour Meter Kit (Figure 13 and Figure 14). • Use the 2-socket connector light harness interconnect when installing the optional LED Light Kit (Figure 13 and Figure 14) Figure 14 1800 or 2100 Series Machines 1. 10-socket connector (light switch) 2. 3-socket connector (hour meter—use with the optional Wireless Hour Meter Kit) Figure 13 800, 1000, or 1600 Series Machine 1.
PAGE 8
Installing the Light Switch (800, 1000, 1600 Series Machines) 1. Remove the knock-out plug at the top left area for the console (A Figure 15). Figure 16 1. Opening (control panel) 3. Notch (body—rocker switch) 2. 2-position rocker switch 4. Left side of the control panel 5. Insert the switch into the opening in the control panel until the switch snaps securely into the panel (Figure 16). Figure 15 1. Knock-out plug (console) 3.
PAGE 9
Installing the Light Switch (1800 or 2100 Series Machines) 1. Remove the plug from the opening at the left face of the control panel (Figure 17). Figure 18 1. Opening (control panel) 3. Notch (body—rocker switch) 2. 2-position rocker switch 4. Front of the control panel 5. Insert the switch into the opening in the control panel until the switch snaps securely into the panel (Figure 18). Figure 17 1. Plug 3. 2-position rocker switch 2. Opening (control panel) 4.
PAGE 10
Connecting the Spark-Plug Wire 6 Connect the spark-plug wire to the terminal of the spark plug as shown in Figure 2 of 1 Preparing the Machine (page 2). Finishing the LED Light and Wireless Hour Meter Harness Kit Installation 7 Installing the Wire Harness to the LED Light Kit and/or Wireless Hour Meter Kit No Parts Required Installing the Control-Panel Cover (1800 or 2100 Series Machines) No Parts Required 1.
PAGE 11
Notes: 11
PAGE 12