Form No. 3327-355 Greensmaster 3050 Greensmaster Traction Unit Model No. 04351—Serial No.
Warning Before Operating . . . . . . . . . . . . . . . . . . . . . . . . . . . . Checking the Engine Oil . . . . . . . . . . . . . . . . . . . Filling the Gas Tank . . . . . . . . . . . . . . . . . . . . . . . Servicing the Hydraulic System . . . . . . . . . . . . . . Tire Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Checking the Torque of the Wheel Nuts . . . . . . . Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Think Safety First . . . . . . . . . . .
This manual uses two other words to highlight information. Important calls attention to special mechanical information and Note: emphasizes general information worthy of special attention. Introduction Read this manual carefully to learn how to operate and maintain your product properly. The information in this manual can help you and others avoid injury and product damage. Although Toro designs and produces safe products, you are responsible for operating the product properly and safely.
• the type of machine is unsuitable for its task; • Do not use on slopes of more than • lack of awareness of the effect of ground conditions, especially slopes; – 5° when mowing on side hills; – 10° when mowing uphill; • incorrect hitching and load distribution. – 15° when mowing downhill. • The owner/user can prevent and is responsible for accidents or injuries occurring to himself or herself, other people, or property. • Remember there is no such thing as a safe slope.
• Be careful during adjustment of the machine to prevent entrapment of the fingers between moving blades and fixed parts of the machine. • Disengage drive to attachments when transporting or not in use. • Stop the engine and disengage drive to attachment • On multi-cylinder/multi-reel machines, take care as rotating one cylinder/reel can cause other cylinders/reels to rotate.
• Keep your body and hands away from pin hole leaks or nozzles that eject hydraulic fluid under high pressure. Use paper or cardboard, not your hands, to search for leaks. Hydraulic fluid escaping under pressure can have sufficient force to penetrate the skin and cause serious injury. Seek immediate medical attention if fluid is injected into skin. • Do not operate the machine while wearing tennis shoes or sneakers.
Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 95-7113 93-8064 (for CE) 93-6668 1. Battery 2. Read the instructions before servicing or performing maintenance. 1. Warning—read the instructions before servicing or performing maintenance. 3. Contains lead; do not discard. 2. Cutting hazard of foot or hand—stop the engine and wait for moving parts to stop.
93-8061 (Replace control panel) 1. Failure/malfunction (Leak detector alarm test) 2. Headlights 3. Off 4. Choke 5. On 6. Slow 7. Fast 8. Engine—stop 9. On 10. Engine—start 11. Read the Operator’s Manual. 12. Continuous variable setting 93-8065 1. Transmission 2. Forward motion 3. Neutral 4. Forward speeds 104-2053 93-7276 1. Explosion hazard—wear eye protection. 2. Caustic liquid/chemical burn hazard—to perform first aid, flush with water. 3. Fire hazard—no fire, open flames, or smoking. 4.
3-6691 1. Read the Operator’s Manual. 93-9898 1. Lock and unlock the reels 93-8069 1. Hot surface/burn hazard—stay a safe distance from the hot surface. 104-2052 Specifications Accessories Note: Specifications and design subject to change without notice. General Specifications Width of Cut 59 in. (149.9 cm) Wheel Tread 49-1/2 in. (125.7 cm) 46-7/8 in. (119.1 cm) 90 in. (228.6 cm) Wheel Base Overall Length Overall Width Net Weight (wet) 69-3/4 in. (117.2 cm) 48-1/2 in. (123.2 cm) 930 lb.
Setup Note: Determine the left and right sides of the machine from the normal operating position. Loose Parts Description Qty. Seat 1 Nut, 5/16 in. 4 Seat cover 1 Wheel assembly 1 Rear spindle spacer 2 Capscrew, 1/2 x 3/4 in. 1 Washer, 1/2 in. 1 Cover 1 Socket head screw, 1/4 x 3/4 in. 1 Locknut, 1/4 in. 1 Washer, 1/4 in. 1 Self tapping screw 2 Capscrew, 1/4 x 5/8 in. 2 Nut, 1/4 in. 2 Gauge bar 1 Machine screw, #10 x 7/8 in. 1 Jam nut, #10 in.
Activating and Charging the Battery Installing the Rear Wheel Assembly 1. Remove the bolt and locknut from the wheel mount holes in the rear castor fork (Fig. 2). Warning 2. Install the rear wheel in the castor fork. Insert the bolt into one of the mounting holes, install a spacer, and slide the bolt through the wheel (Fig. 2). Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm.
1 Mounting the Seat 3 Note: Mount the seat slides in the front set of mounting holes to gain an additional 3 in. (7.6 cm) in the forward adjustment, or in the rear mounting holes for an additional 3 in. (7.6 cm) in the rearward adjustment. 1. Support the seat base in the up position with the seat support rod. 2 2. Remove the locknuts securing the seat slides to the plywood shipping base. Discard the locknuts. 3. Secure the seat, seat panel, and seat slides to the seat support with the locknuts (5/16 in.
Installing the Battery Installing the Cutting Units 1. Mount the battery with the battery terminals toward the hydraulic tank on the machine. For Cutting Unit Models 04404, 04406, 04408, 04450, and 04468 Note: When sharpening, setting the height-of-cut, or performing other maintenance procedures on the cutting units, store the cutting unit reel motors in the support tubes on the front of the frame to prevent damage to the hoses.
4. Remove the protective covers from the cutting units and the reel drive motor shafts. Coat the spline shaft of the motor with clean grease and install the motor by rotating the motor clockwise so the motor flanges clear the studs. Rotate the motor counterclockwise until the flanges are encircling the studs and tighten the mounting nuts (Fig. 9). 4 Note: Retain the protective covers for the cutting units.
3. Slide the cutting unit under the pull frame while hooking the lift roller onto the lift arm (Fig. 12). 7. Assemble the mounting capscrews for the reel drive motor to each cutting unit. Leave approximately 1/2 in. (13 mm) of threads exposed on each mounting capscrew (Fig. 14). 4. Slide the sleeve back on the ball joint and rotate the pull arm down so the socket fits over the ball stud. Release the sleeve so it slides over the stud and locks the assemblies together (Fig. 12). 5.
Before Operating Filling the Gas Tank Note: Determine the left and right sides of the machine from the normal operating position. Use unleaded regular gasoline suitable for automotive use (85 pump octane minimum). Leaded regular gasoline may be used if unleaded regular is not available. Important Never use methanol, gasoline containing methanol, or gasohol containing more than 10% ethanol because the fuel system could be damaged. Do not mix oil with gasoline.
2. Install the fuel tank cap securely. Wipe up any gasoline that may have spilled. 1 Sunoco Sun Hyd. Oil 2105 Texaco Rando HDZ 46 Universal Tractor Hydraulic Fluid Mobil Mobilfluid 424 Amoco Chevron Conoco Figure 16 1000 Fluid Tractor Hydraulic Fluid Hydroclear Powertran Esso Hydraul Gulf Universal Tractor Fluid Kendall 1.
Fluid level 3-1/2 in. from top of fill hole Fluids offer similar performance for those who prefer them, with perhaps some slight loss of efficiency at high ambient temperatures compared to the Type 46/48 fluids. Group 2 fluids are recommended for heavy-duty use in hot climates where ambient temperatures range from about 65°F (18°C) to 120°F (49°C).
The use of protective equipment, such as but not limited to, for eyes, ears, feet, and head is recommended. 3 Caution 2 This machine produces sound levels in excess of 85 dBA at the operators ear and can cause hearing loss through extended periods of exposure. 4 Wear hearing protection when operating this machine. 1 5 1 2 Figure 19 1. Mow pedal 2. Lift pedal 3. Traction pedal Figure 18 1. Caution 2. Wear hearing protection 4. Brake pedal 5.
Choke Mow Lockout Lever To start a cold engine, close the carburetor choke by moving the choke control (Fig. 21) forward to the Closed position. After the engine starts, regulate the choke to keep the engine running smoothly. As soon as possible, open the choke by pulling it rearward to the Open position. A warm engine requires little or no choking. The lockout lever locks the mow pedal preventing accidental starting of the cutting units. To unlock it, pull the mow lockout pin outward (Fig.
lead to major problems, are noted and can be corrected. Inspect the machine frequently during break-in for signs of oil leakage, loose fasteners, or any other malfunction. E. Check for oil leaks. If oil leaks appear, check the tightness of the hydraulic fittings. If oil leaks continue to appear, contact your local Toro Distributor for assistance and, if necessary, replacement parts. To ensure optimum performance of the brake system, burnish (break-in) the brakes before using the machine.
7. Repeat step 6 with the shift selector in the #2 position. If the engine does not stop, stop the engine and find the problem before operating the machine again. If assistance is required, contact your local Toro Distributor. Perform the following system checks daily to be sure the interlock system is operating correctly: 1. Sit on the seat, engage the parking brake, and move the shift selector to neutral. Remove your foot from the traction pedal and make sure the pedal is in neutral.
much of the green as possible should be cut to minimize the amount of grass left to mow around the outer periphery. Important If you shift to the No. 2 position while cutting greens, no increase in speed will result. However, a sudden increase in speed will develop when you actuate the lift pedal. For safety purposes, it is recommended that you use only the No. 1 position for cutting greens and the No. 2 position for transport.
Transport Operation Inspection and Cleanup After Mowing Make sure that the cutting units are in the full up position. Set the shift selector in No. 2 if conditions will permit faster ground speed. Shift to No. 1 and operate at slower ground speeds in rough or hilly areas. Use the brakes to slow the machine while going down steep hills to avoid loss of control. Always approach rough areas at a reduced speed (shift selector in No. 1), and cross severe undulations carefully.
Daily Maintenance Checklist Duplicate this page for routine use. For the week of: Maintenance Check Item Mon. Tues. Check the safety interlock operation. Check the instrument operation. Check the brake operation. Check the fuel level. Check the engine oil level. Clean the engine air cooling fins. Inspect the air filter pre-cleaner. Check any unusual engine noises. Check the hydraulic hoses for damage. Check for fluid leaks. Check the tire pressure. Check the reel-to-bedknife adjustment.
Caution If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure you or other bystanders. Remove the key from the ignition and disconnect the wire from the spark plug before you do any maintenance. Set the wire aside so that it does not accidentally contact the spark plug. Lubrication The traction unit has grease fittings that must be lubricated regularly with No. 2 General Purpose Lithium-Base Grease.
Changing the Engine Oil and Filter Change the oil and filter after the first 8 hours of operation. Thereafter, change the oil every 50 hours and the filter every 100 hours. 1. Remove the drain plug (Fig. 34) and let oil flow into a drain pan. When the oil stops, install the drain plug. Figure 31 2 1 Figure 34 1. Drain plug 2. Oil filter 2. Remove the oil filter (Fig. 34). Apply a light coat of clean oil to the new filter gasket. 3.
Servicing the Air Cleaner 5. Reinstall the foam element, paper element, and air cleaner cover. Service the air cleaner foam pre-cleaner after every 50 operating hours and the air cleaner cartridge after every 100 operating hours. More frequent cleaning is required when operating in dusty or dirty conditions. Important Do not operate the engine without the air cleaner element because extreme engine wear and damage will likely result. 1. Release the locking clips and remove the air cleaner cover (Fig.
Adjusting the Choke Control 3. Bend the governed idle spring anchor tang (Fig. 38) to attain an idle speed of 1450±50 RPM. Check the speed with a tachometer. 1. Loosen the cable clamp screw securing the cable to the engine (Fig. 37). 2. Move the remote choke control lever forward to the Closed position. 3. Pull firmly on the choke cable until the choke butterfly is completely closed, then tighten the cable clamp screw (Fig. 37).
Changing the Hydraulic Oil and Filter 4. Set the air gap between the center and side of the electrodes at 0.030 in. (.76 mm) (Fig. 39) Install the correctly gapped spark plug w/gasket seal, and tighten the plug to 200 in.-lb. (23 N⋅m). If a torque wrench is not used, tighten the plug firmly. Normally, change the hydraulic oil and filter after every 2000 operating hours. If the oil becomes contaminated, contact your local Toro distributor because the system must be flushed.
4. Fill the hydraulic tank with approximately 4.5 gallons of hydraulic oil; refer to Checking the Hydraulic System, page 17. 2. If the brakes do not lock equally, disconnect the brake rods by removing the cotter pin and clevis pin (Fig. 43). 1 5. Start the machine and run it at idle for 3 to 5 minutes to circulate the fluid and remove any air trapped in the system. Stop the machine and recheck the fluid level. 6. Dispose of the used oil properly.
2 1 3 4 2 1 Figure 44 1. Mounting capscrews 2. Cam blocks Figure 46 1. Jam nut 2. Yoke Adjusting the Lift and Mow Pedal Height To gain proper spool travel in the valve bank, adjust the lift and mow pedals to equal heights as follows: 3. Control rod 4. Adjustment lever Leveling the Lift and Mow Pedals 1. Place 1, 2, and 3 spools in neutral (center of travel) and remove the transfer rod guard from the foot panel (Fig. 45).
Adjusting the Traction Pedal Adjusting Cutting Unit Lift and Drop To check the forward and reverse operation of the traction pedal, proceed as follows: The cutting unit lift/drop circuit is equipped with a flow control valve. This valve is preset at the factory at approximately 3-1/2 turns open, but an adjustment may be required to compensate for differences in hydraulic oil temperatures, mowing speeds, etc. If an adjustment is required, proceed as follows: Adjusting Forward 1.
Replacing the Seat Switch Replacing the Traction Switch 1. Pivot the seat forward and secure it with the support rod. 1. Pivot the seat forward and secure it with the support rod.. 2. Remove the boot from the button end of the seat switch (Fig. 50) and retain it for installation on the replacement switch. Unplug the switch connectors. 2. Unplug the switch connectors from the traction switch installed in the valve bank bonnet on the selector valve section (Fig. 50). 1 3.
Servicing the Steering Assembly 5. Connect a continuity tester or ohm meter across the switch terminals and turn the switch in until continuity occurs. Then rotate the switch in 1/2 turn (180 degrees) and secure the jam nut to 75 in.-lb. (8 N⋅m) against the bonnet. The steering cable tension should be adjusted whenever play is felt in the steering wheel. A loose steering cable will make it difficult to steer in a straight line.
Battery Care If corrosion occurs at the terminals, disconnect the cables, negative (–) cable first, and scrape the clamps and terminals separately. Reconnect the cables, positive (+) cable first, and coat the terminals with petroleum jelly. Warning Storage Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.
FRAME GND (–) (+) ENGINE SP Y W VIO BK BN FL R PARKING BRAKE (IN OFF POSITION) NEUTRAL SW. (CLOSED IN NEUTRAL) FUEL SOLENOID BN ALTERNATOR FL SP OR 10A STARTER SOLENOID SPLICE YELLOW WHITE RED R W PURPLE PU MAGNETO ENGINE GND BATTERY ORANGE OR STARTER FUSIBLE LINK GRAY BLUE BU GY BROWN BN FL BLACK BK Y W D2 SP VIO X B W D1 VIO X BN S 86 87 87a 85 30 GY VOLT METER MOW SW.
LH LH 38 ADJUSTABLE FLOW RESTRICTOR LIFT CYLINDERS RH RH 2000 PSI (141 KG/SQ CM) ONE WAY ORIFICE CENTER CENTER REEL MOTORS .43 CU. IN/REV. (7 CU. CM/REV.) 2000 PSI (141 KG/SQ CM) 2000 PSI (141 KG/SQ CM) SAFETY INTERLOCK SWITCH 3 .58 IN /REV (9.5 CU CM/REV) N 1ST 2ND 3 .33 IN /REV (5.4 CU CM/REV) 1850 PSI (130 KG/SQ CM) SAFETY INTERLOCK SWITCH REV N FWD LH HYDRAULIC TANK PUMP 2900 RPM MAX 3 .33 IN /REV (5.4 CU CM/REV) VALVE BANK RH WHEEL DRIVE MOTORS 10.3 CU. IN/REV. (169 CU.
Troubleshooting Problem Possible Causes Corrective Action Engine: g 1. The fuel tank is empty. 1. Fill the fuel tank. The engine loses power. 2. A fuel line is clogged or there is debris in the fuel tank. 2. Clean the fuel tank. Use clean gasoline. 3. The fuel filter is clogged. 3. Replace the filter. 4. The oil level in the crankcase is low. 4. Add oil to the proper level. Check the level more frequently. 5. The oil in the crankcase is incorrect. 5. Replace it with the correct oil. 6.
Problem Possible Causes Corrective Action 3. The traction relief cartridge in the #4 spool section is open. 3. Remove the relief cartridge. Repair or replace it. 4. A traction motor lacks efficiency. There is fluid leaking past the internal gears. 4. Test to identify the faulty motor. Repair or replace the motor. 5. The hydraulic pump lacks efficiency. There is fluid leaking past the internal gears. 5. Test to verify a diagnosis. Repair or replace the pump. 1. The brakes are dragging. 1.
Problem Possible Causes Corrective Action 1. A lift cylinder is leaking internally. 1. Raise the units and block them up. Remove the lines from the brazed tube and remove the blocks. The line that leaks fluid is attached to the bad cylinder. Repair the cylinder. 2. The lift check plug seals in the #1 spool body are damaged. 2. Remove the lift check plugs. Replace the o-ring assemblies. 3. A detent stud is loose in the #2 spool. 3. Remove the adjustment cap from the #2 spool bonnet.
Problem Possible Causes Corrective Action The engine fails to crank, regardless of the shift selector or mow pedal position. 1. The mow/lift switch, traction switch, and/or seat switch are adjusted incorrectly or are damaged. 1. Refer to Replacing the Traction Switch, Replacing the Mow/Lift Switch, and/or Replacing the Seat Switch. 2. The battery terminals are corroded. 2. Clean the terminals. 3. The mow/lift or traction switch wires are loose. 3. Check the wires and connect them properly. 4.
Problem Possible Causes Corrective Action The engine does not continue to run when sitting on the seat and the shift selector is placed in gear or the mow pedal is depressed. 1. The seat switch is adjusted incorrectly or is damaged. 1. Refer to Replacing the Seat Switch. 2. The seat return pin spring is jammed in the up position. 2. Loosen and lubricate the jammed parts so that the pin operates freely. Replace the spring if it is damaged.
The Toro General Commercial Products Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your 1996 or newer Toro Commercial Product (“Product”) purchased after January 1, 1997, to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first.
