Operator's Manual
$!# Tricycle vehicle with two front wheels
providing drive and one rear wheel providing steering.
Operator sits in center over #1 cutting unit with #2 and
#3 cutting units in front of vehicle.
!## Certified to meet ANSI specification B7
1.4-1 990 and European CE standards.
: Briggs & Stratton/Daihatsu three cylinder
water cooled engine. 51.9 cu. in. (850 cc) Full pressure
lubrication, oil filter. 21.0 hp at 3600 rpm, 14.5 hp at
2600 rpm. Engine governed to 2750 ±50 rpm high idle,
1500 ±50 rpm low idle (no load).
! Welded steel tube construction in an A" frame
configuration.
! ! Donaldson Corp. heavy duty remote air
cleaner.
#! Power steering. Danfoss open center,
nonĆload reacting steering valve with power beyond for
raise/lower circuit and Hydrostat charge circuit. 13"
round steering wheel. No-tool quick adjust steering
arm position, with arm motion allowing a wide range of
operator sizes. Steering cylinder has a 1.50 inch bore x
6.25 stroke with through shaft design for accurate
straight line steering.
$ #& 6 gallons (22.7 liters) capacity, diesel.
&!$ #& 5.5 gallon (20.8 liter) nylon oil
reservoir. Mobile DTE 15 M standard, Mobile EAL 224H
approved. Hydraulic oil filter has 5 micron long life
filtration of circuit.
!# !% Hydrostatic piston pump, closed loop
system. Foot pedal forward and reverse; infinitely
variable. Two front wheel orbit motors, 10.3 in./rev
displacement.
!$ Forward mowing speed is variable
from 2 to 5 mph (3.2 to 8 km/h), adjusted by stop on
pedal mechanism. Mow speed setting does not affect
transport speed. Maximum transport speed is 8.8 mph
(14.1 km/h), may be reduced by adjusting stop in
footrest pan without affecting mow speeds. Reverse is
2.5 mph (4.0 km/h).
$! # !""$! 10 psi average at
recommended minimum tire pressures, with a 200 lb.
operator and cutting units down.
!" Three 19 x 10.50 x 8, 2 ply pneumatic tubeless
demountable and interchangeable. Smooth tread.
! !""$! 8-12 psi front
8-15 psi rear
!" 6" drum type mechanical with rack and pawl
lock for parking.
$## # !% Hydraulic drive; one .58 in./ (9.5
cc) rev gear pump section powers three reel motors in
series. Manifold block with cartridge valves controls
flow, electrical on/off. Reel motors have .73in/
(12.0 cc) rev displacement, low pressure case drains,
and Toro exclusive twist-mount" partial flange
cut-away for fast installation.
Dependent on mowing ground speed, reel rpm,
and number of reel blades. Mowing ground speed is
easily changed by adjusting the pedal mow stop (this
will not affect transport speed). lncreasing ground
speed will increase clip length and decrease cuts per
meter. In general, the quality of cut will be best when
clip and HOC are nearly equal.
$## # $" " Cutting units are
completely free floating, each attaching to the traction
unit by direct pull links and lifted by a centered lift arm.
Baskets are supported by carrier frames that are
suspended off the ground by adjustable stops in the
tractor frame weldment. Cutting unit floatation is
unaffected by basket content.
#! #$!" Maintenance free 12 volt battery
with 530 cold cranking amps at 0 degrees F. and 85
minutes reserve capacity at 85 degrees F. 40 amp
alternator, circuit fused at 40 amps. Ignition switch/key.
Seat switch. High temperature engine kill override
switch. Harness terminals. fuse slot, and console
switch location available for optional lights installation.
#!"$" Hand operated throttle,
raise/lower-mow lever, and functional control (neutral,
mow, transport) lever. Foot operated traction drive
brakes. Water in fuel warning light. Hour meter and 4
bulb warning cluster.
#!"
Traction pedal locks when functional control lever is in
neutral.
Engine cranking requires functional control lever in
neutral, operator does not have to be in seat.
Engine will shut off if
operator leaves seat without
functional control lever in neutral.
Reels turning forward requires operator in seat,
functional control lever in mow and raise/lower/mow
control momentarily engaged.
Reels turning backward for backlap requires optional
variable reel speed kit installed. Then the reels are
allowed to turn backwards when the functional control
lever in neutral and the backlap switch is closed,
showing reel direction is reversed.
# Contour seat with high backrest. 7 inch fore/aft
slider adjustment with two mounting positions allowing
9 inch total seat travel. Operator manual tube mounted
on the seat back for easy access.