Form No. 3391-376 Rev A Dethatching Unit Greensmaster® 3000 Series Traction Unit Model No. 04479—Serial No. 315000001 and Up Register at www.Toro.com.
WARNING Model No. CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Serial No. This manual identifies potential hazards and has safety messages identified by the safety alert symbol (Figure 2), which signals a hazard that may cause serious injury or death if you do not follow the recommended precautions. Introduction Figure 2 1.
Contents Safety Safety ........................................................................... 3 Safety and Instructional Decals ................................. 4 Setup ............................................................................ 5 1 Installing the Front Roller ...................................... 5 2 Repositioning the Counter Weights.......................... 5 3 Installing the Hoop Link, Offset Link, or Chain Link ..................................................................
the Toro logo to assure genuineness. Using unapproved replacement parts and accessories could void the warranty of The Toro Company. Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 104-7729 1. Warning—read the instructions before servicing or performing maintenance. 2. Cutting/dismemberment hazard; hand or foot—stop the engine and wait for moving parts to stop.
Setup 3. Remove the 2 Allen-head screws that secure the motor mount to the left end of the dethatching unit. 1 4. Remove the motor mount (Figure 4). 5. Apply grease to the inside diameter of the drive spline (Figure 4). Installing the Front Roller No Parts Required Procedure The dethatching unit is shipped without a front roller. Install the roller using the loose parts supplied with the dethatching unit and installation instructions included with the roller.
A hoop link (part no. 105-5740) is required for the Greensmaster 3000, 3000-D, 3050, 3100, 3150, and 3150-Q traction units (it is supplied with the above Greensmaster traction units). Install the hoop link to the top of the dethatching unit with 2 capscrews. Note: Torque the capscrews to 34 to 40 N-m (25 to 30 ft-lb) (Figure 5). Figure 6 1. Offset lift hook A chain link (part no. 106-2601) and a mounting bracket (part no. 105-5738) may also be used on the Greensmaster 3250-D traction unit. Figure 5 1.
4 5 Adjusting the Reel Blades for Positive Setting (Above Ground) Adjusting the Reel Blades For Negative Setting (Below Ground) No Parts Required No Parts Required Procedure Procedure 1. Place the dethatching unit on a level surface. Note: Maximum recommended negative setting is 5 mm (3/16 inch) deep blade penetration. 2. Place a gauge bar, which has the desired height of blade above ground, under each end of the dethatching unit (Figure 8). 1. Place the dethatching unit on a level surface. 2.
6 Installing the Dethatching Unit No Parts Required Important: If you set the dethatching reel at a negative setting, take care to prevent damaging the reel blades, due to contact with concrete floors or paved surfaces. Note: The dethatching unit comes configured for left-hand drive from the factory. It may need to be configured for a right-hand drive. Refer to 2 Repositioning the Counter Weights (page 5).
Product Overview Specifications Tractors These dethatching units will mount on the Greensmaster 3000, 3000-D, 3050, 3100, 3150, 3250-D and 3150-Q Traction Units. Height-of-cut Dethatching depth is adjusted on the front roller by two vertical screws and held by two locking capscrews Height-of-cut Range Bench HOC range is 4.78 mm (0.188 inch) below ground level to 6.35 mm (0.250 inch) above ground level.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Disassembling the Reel Disassemble the reel whenever you need to change a blade or replace the reel bearings. Important: Ensure that the 2 shaft retainers and spacer are in place before installing the bearing on the reel (Figure 10). Torque the insert nuts to 136 N-m (100 lb-ft). Figure 10 1. Left-hand threaded insert nut 2. Bearing 4. Spacer 3. Seal 6. Shaft retainer (Install these first) 5.
Notes: 11
Notes: 12
Notes: 13
Declaration of Incorporation The Toro Company, 8111 Lyndale Ave. South, Bloomington, MN, USA declares that the following unit(s) conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain Toro models as indicated on the relevant Declarations of Conformity. Model No. 04479 Serial No.
International Distributor List Distributor: Country: Phone Number: Distributor: Phone Number: 57 1 236 4079 Colombia Japan 81 3 3252 2285 Czech Republic 420 255 704 220 420 255 704 Slovakia 220 Argentina 54 11 4 821 9999 Russia 7 495 411 61 20 Ecuador 593 4 239 6970 Finland 358 987 00733 Agrolanc Kft Balama Prima Engineering Equip. B-Ray Corporation Hungary Hong Kong Korea 36 27 539 640 852 2155 2163 82 32 551 2076 Maquiver S.A. Maruyama Mfg. Co. Inc. Mountfield a.s.
Toro General Commercial Product Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
