Form No. 3445-360 Rev A Dethatching Unit Greensmaster® 3000 Series Traction Unit Model No. 04479—Serial No. 408000000 and Up Register at www.Toro.com.
This product complies with all relevant European directives. For details, please see the Declaration of Incorporation (DOI) at the back of this publication. Model No. Serial No. This manual identifies potential hazards and has safety messages identified by the safety-alert symbol (Figure 2), which signals a hazard that may cause serious injury or death if you do not follow the recommended precautions.
Cutting Unit Safety Safety • The cutting unit is only a complete machine when This machine has been designed in accordance with EN ISO 5395 and ANSI B71.4:2017. installed on a traction unit. Read the traction unit Operator’s Manual carefully for complete instructions on the safe use of the machine.
Setup 1 Installing the Front Roller No Parts Required Procedure The dethatching unit is shipped without a front roller. Install the roller using the loose parts supplied with the dethatching unit and Installation Instructions included with the roller. g016405 2 Figure 3 1. Counterweight Repositioning the Counterweights No Parts Required 3. Remove the 2 Allen-head screws that secure the motor mount to the left end of the dethatching unit. 4. Remove the motor mount (Figure 4). 5.
7. • An offset link (Part No. 110-2397) is required On the left end of the dethatching unit, apply a light coating of oil to the O-ring and install the counterweight with the screws previously removed. for the Greensmaster 3250-D traction units (it is supplied with the Greensmaster 3250-D traction unit). Note: Torque the screws to 16 to 20 N-m (12 1. Position the lift hook offset toward the front of the dethatching unit. 2.
4. Rotate the height-of-cut until both ends of the front roller contact the level surface. 5. Verify contact by using a piece of paper to check each roller end. 6. Tighten both height-of-cut knob locknuts. 5 g011932 Figure 7 1. Chain link Adjusting the Reel Blades For Negative Setting (Below Ground) 2.
6. Tighten both height-of-cut knob locknuts. 6 Installing the Dethatching Unit No Parts Required Important: If you set the dethatching reel at a negative setting, take care to prevent damaging the reel blades, due to contact with concrete floors or paved surfaces. Note: The dethatching unit comes configured for left-hand drive from the factory. It may need to be configured for a right-hand drive. Refer to 2 Repositioning the Counterweights (page 4).
Product Overview Specifications Traction-unit compatibility Height of cut Height-of-cut range Reel bearings Rollers Grass shield Counterweight Net weight The dethatching unit mounts on the Greensmaster 3000, 3000-D, 3050, 3100, 3150, 3250-D and 3150-Q traction units. Dethatching depth is adjusted on the front roller by 2 vertical screws and held by 2 locking capscrews Bench HOC range is 4.78 mm (0.188 inch) below ground level to 6.35 mm (0.250 inch) above ground level.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Disassembling the Reel Disassemble the reel whenever you need to change a blade or replace the reel bearings. Important: Ensure that the 2 shaft retainers and spacer are in place before installing the bearing on the reel (Figure 10). Torque the insert nuts to 136 N∙m (100 ft-lb). g346400 Figure 11 1. End hex spacer g016597 Figure 10 1. Left-hand threaded insert nut 2. Bearing 4. Spacer 3. Seal 6.
Servicing the Roller The Greens Roller Rebuild Kit (Part No. 140-5552) and the Greens Roller Rebuild Tool Kit (Part No. 140-5553) (Figure 12) are available for servicing the roller. The Roller Rebuild Kit includes all the bearings, bearing nuts, and seals to rebuild a roller. The Roller Rebuild Tool Kit includes all the tools and the installation instructions required to rebuild a roller with the roller rebuild kit. Refer to your parts catalog or contact your authorized Toro distributor for assistance.
Notes:
Notes:
Notes:
Declaration of Incorporation The Toro Company, 8111 Lyndale Ave. South, Bloomington, MN, USA declares that the following unit(s) conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain Toro models as indicated on the relevant Declarations of Conformity. Model No. 04479 Serial No.
The Toro Warranty Two-Year or 1,500 Hours Limited Warranty Parts Conditions and Products Covered The Toro Company warrants your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for 2 years or 1,500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
