FORM NO. 3318-307 GB Rev A MODEL NO. 04482—60001 & UP MODEL NO.
Table of Contents SPECIFICATIONS ADJUSTING CUTTING UNIT Adjusting The bedknife To The Reel Leveling Front Roller To The Reel Adjusting Height-of-Cut Page 2 3 4 4 5 OPERATING INSTRUCTIONS Cutting Unit Daily Adjustments LUBRICATION Greasing Bearings And Bushings BACKLAPPING THE CUTTING UNITS 5 5 6 6 6 Specifications Height-of-Cut: The cutting height is adjusted on rear roller by two vertical screws and held by two locking capscrews. Bench height-of-cut range is 2.4mm to l9mm.
Adjusting the Cutting Units do so may result in damage to the cutting unit. Note: Left and right sides of the cutting unit refer to normal operating position. After the cutting unit is unboxed, use the following procedures to assure the cutting units are adjusted properly. 1. Check each end of the reel for grease. Grease should be visibly evident in the reel bearings. 2. Insure that all nuts and bolts are securely fastened. 3. Position the lift roller to match suspension.
Adjusting Cutting Units 2. Position a 6 mm or thicker plate under the reel blades and against the front face of the bedknife. Note: Be sure the plate covers the full length of the reel blades and three blades contact the plate. 3. Loosen the locknuts retaining the right-front roller bracket. typically used. The upper position is more aggressive and may be used in a limited height-of-cut range (.140-.250") if conditions warrant. ADJUSTING THE HEIGHT OF CUT (Fig. 4) 1.
Adjusting the Cutting Units IMPORTANT: Repeat the procedure on each end of the bedknife and tighten locknuts that retain rear roller brackets on each end. CUTTING UNIT CHARACTERISTICS The single-knob bedknife-to-reel adjustment system incorporated in this cutting unit simplifies the adjustment procedure needed to deliver optimum mowing performance.
Lubrication GREASING BEARINGS AND BUSHINGS Each cutting unit has (6) grease fittings that must be lubricated regularly with No. 2 General Purpose Lithium Base Grease. sure or grease seals will be permanently damaged. 3. Wipe away excess grease. The grease fitting locations and quantities are: Reel bearings (2) and front and rear rollers (2 ea.) (Fig. 5) IMPORTANT: Lubricating the cutting units immediately after washing helps purge water from the bearings and increases bearing life. 1.
W-X?hg W-X? W-X? W-X? W-X? W-X? W-X? W-X? W-X? W-X? W-X? W-X? W-X? W-X? W-X? W-X? W-X? W-X? W-X? W-X? W-X? W-X? W-X? W-X? W-X? W-X? W-X? W-X? W-X? W-X? W-X? W-X? W-X? W-X? W-X? W-X? W-X? W-X?hg ?W-X ?@@@@@@6X?f?W&@)Xf?W2@@@@@@@@@@@@@6Xf?W&@)XgW2@@@@@@@@@@@@6Xf?W&@)XgW2@@@@@@@@@@@@6Xf?W&@)XgW2@@@@@@@@@@@@6Xf?W&@)XgW2@@@@@@@@@@@@6Xf?W&@)XgW2@@@@@@@@@@@@6Xf?W&@)XgW2@@@@@@@@@@@@6Xf?W&@)XgW2@@@@@@@@@@@@6Xf?W&@)XgW2@@@@@@@@@@@@6Xf?W&@)XgW2@@@@@@@@@@@@6Xf?W&@)XgW2@@@@@@@@@@@@6Xf?W&@)XgW2@@@@@@@@@@@@6Xf?W&@)XgW2@@@
