Operator's Manual

ManualsBrandsToro ManualsAttachmentsSpiker, Greensmaster 3000 Series

FormNo.3390-874RevA

SpikerKit

Greensmaster

3000Series

ModelNo.04494—SerialNo.315000001andUp

Operator'sManual

ThisproductcomplieswithallrelevantEuropeandirectives;

fordetails,pleaseseetheseparateproductspecicDeclaration

ofConformity(DOC)sheet.

WARNING

CALIFORNIA

Proposition65Warning

Thisproductcontainsachemicalorchemicals

knowntotheStateofCaliforniatocausecancer,

birthdefects,orreproductiveharm.

Setup

MountingthePullArm

Bumpers(Greensmaster3050,

3100,3150,and3200)

1.UsingthedimensionsshowninFigure1,drill2

holeswithadiameterof5.6mm(0.221inch)onthe

undersideofeachpullframecrosstube.

G028061

Figure1

1.49.3cm(19.4inches)3.1.9cm(3/4inches)

2.9cm(3.5inches)4.Pullframecrosstube

2.Mountthe2recessedbumperstotheundersideofeach

pullframecrosstubewith2washer-headself-tapping

screws(Figure2).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3390-874*A

Summary of content (8 pages)

PAGE 1
Form No. 3390-874 Rev A Spiker Kit Greensmaster® 3000 Series Model No. 04494—Serial No. 315000001 and Up Operator's Manual This product complies with all relevant European directives; for details, please see the separate product specific Declaration of Conformity (DOC) sheet. WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
PAGE 2
3 1 4 2 1 G028062 G028063 Figure 3 Figure 2 1. Recessed bumper 1. Roller sets 2. Ball socket 2. Washer-head self-tapping screw 3. Carrier frame 4. Pull frame 2. Slide the spiker unit in front of the traction-unit pull frame until the lift arm is positioned between the lift pivot plates (Figure 4). Adjusting the Rear Roller Scrapers 1 The rear roller scraper is adjusted at the factory, but can be adjusted to meet turf conditions. 2 1. Loosen the locknuts securing the scraper to the frame.
PAGE 3
5. Mount the pull link assemblies to the Greensmaster 3050, 3100, and 3150 pull arms as follows: A. Remove the fasteners securing the roller shaft and pull arms to each end of the carrier frame (Figure 7). 1 3 2 5 G028065 1 4 Figure 5 Greensmaster 3200 shown G028067 2 Figure 7 1. Ball stud (large diameter) 4. Nylon bushing 2. Ball joint receiver 5. Pull link assembly 1. Ball joint receiver 2. Pull link assembly 3. Spacer B.
PAGE 4
1 2 4 G028068 3 2 1 G028070 Figure 10 Figure 8 1. Mounting screws B. 2. Reel motor Install the motor by rotating it clockwise so that the motor flanges clear the screws. Rotate the motor counterclockwise until the flanges encircle the screws. Tighten the screws. 7. Store the rear reel motor on the Greensmaster 3150, 3200, and 3250 the same as the front reel motors. 8. Store the rear reel motor on the Greensmaster 3100 and 3050 as follows: 1. Self-tapping screw 3. Storage tube 2. Spacer 4.
PAGE 5
Operation Maintenance Training Period Lubricating the Spiker Units Before spiking greens with the spiker attachments, find a clear area and practice starting, stopping, raising, lowering, and spiking with the spiker reels. This training period will be beneficial to the operator in gaining confidence in the performance of the spiker reels. There are 4 grease fittings on each spiker unit, which must be lubricated after every 15 hours of operation. Lubricate using a general-purpose lithium-based grease.
PAGE 6
Declaration of Incorporation The Toro Company, 8111 Lyndale Ave. South, Bloomington, MN, USA declares that the following unit(s) conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain Toro models as indicated on the relevant Declarations of Conformity. Model No. 04494 Serial No.
PAGE 7
International Distributor List Distributor: Country: Phone Number: Distributor: Phone Number: 57 1 236 4079 Colombia Japan 81 3 3252 2285 Czech Republic 420 255 704 220 420 255 704 Slovakia 220 Argentina 54 11 4 821 9999 Russia 7 495 411 61 20 Ecuador 593 4 239 6970 Finland 358 987 00733 Agrolanc Kft Balama Prima Engineering Equip. B-Ray Corporation Hungary Hong Kong Korea 36 27 539 640 852 2155 2163 82 32 551 2076 Maquiver S.A. Maruyama Mfg. Co. Inc. Mountfield a.s.
PAGE 8
Toro General Commercial Product Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).