Operator's Manual

ManualsBrandsToro ManualsAttachmentsTri-Roller, Greensmaster 3000 Series

FormNo.3329-231RevB

Tri-RollerKit

forGreensmaster3000Series

ModelNo.04495—SerialNo.200000501andUp

InstallationInstructions

Installation

Important:ReadthisOperator’sManual

thoroughlybeforeoperatingtheTri-RollerKit.

Failuretodosomayresultindamagetotheroller.

MountingthePullArm

Bumpers(Greensmaster3050,

3100,3150and3200)

1.UsingthedimensionsshowninFigure1,locate,

mark,anddrill2holes(0.221in.diameter)inthe

undersideofeachpullframecrosstube.

Note:Theholesmayalreadybepresentinthecross

tubes.

G010402

Figure1

Greensmaster3050,3100,and3150Shown

1.Pullframecrosstube

3.3.54inches

2.19.43inches4..75inch

2.Mount2recessedbumperstotheundersideofeach

pullframecrosstubewith2washerheadselftapping

screws(1/4x3/4in.)(Figure2).

G010403

Figure2

Greensmaster3050,3100and3150Shown

1.Recessedbumper

AdjustingtheRearRoller

Scrapers

Note:Therearrollerscraperisadjustedatthefactory,

butcanbeadjustedtomeetturfconditions.

1.Loosenthelocknutssecuringthescrapertothe

frame.

2.Adjustthescraperuntilthereis0.03-0.06in.

clearancebetweentheedgeofthescraperandroller.

3.Tightenthelocknutssecuringthescraper.

MountingtheTri-Rollers

1.Parkthemachineonalevelsurface,lowerthelift

arms,stoptheengine,andsettheparkingbrake.

Note:Ifthecarrierframesareequippedwithsingle

pointpullframes,thepullframeandattachingball

jointmustberemoved(Figure3).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3329-231 Rev B Tri-Roller Kit for Greensmaster 3000 Series Model No. 04495—Serial No. 200000501 and Up Installation Instructions Installation Important: Read this Operator’s Manual thoroughly before operating the Tri-Roller Kit. Failure to do so may result in damage to the roller. Mounting the Pull Arm Bumpers (Greensmaster 3050, 3100, 3150 and 3200) 1 1. Using the dimensions shown in Figure 1, locate, mark, and drill 2 holes (0.221 in.
PAGE 2
1 3 2 5 4 4 4 G010404 Figure 3 Greensmaster 3200 Only 1. Ball socket 2. Pull frame 2 1 3 3. Carrier frame 4. Roller sets G010406 Figure 5 Greensmaster 3200 Shown 1. Pull link assembly 2. Ball joint receiver 3. Nylon bushing 2. Slide the tri-roller under the traction unit pull frame while hooking the lift roller onto the lift arm (Figure 4). 4. Spacer 5. Ball stud (large diameter) 2 1 G010405 5 Figure 4 1. Lift roller 2. Lift arm 3.
PAGE 3
Maintenance section of the traction unit Operator’s Manual. 7. Store the rear reel motor on the Greensmaster 3100 and Greensmaster 3050 as follows: A. Using the dimensions shown in Figure 9 for the Greensmaster 3100 and Figure 10 for the Greensmaster 3050, locate and scribe a line on the appropriate frame member. 3 2 1 2 1 G010410 Figure 9 1. .90 inch G010408 2. 1.62 inch Figure 7 1. Pull link assembly 2. Ball joint receiver 3.
PAGE 4
Operation 3 2 Training Period Before rolling greens, we suggest that you find a clear area and practice starting, stopping, raising, lowering, and rolling with the tri-roller. This training period will be beneficial to the operator in gaining confidence in the performance of the tri-roller. G010412 1 4 Figure 11 1. Reel motor 2. Self tapping screw 3. Spacer 4. Storage tube Operating Tips Maintain a straight line when rolling. Do not turn when the tri-rollers are on the ground. 8.
PAGE 5
Maintenance Lubrication There are 4 grease fittings on each tri-roller, which must be lubricated after every 15 hours of operation. Lubricate using a #2 multi-purpose lithium base grease. A hand operated grease gun is recommended for best results. 1. Wipe each grease fitting with a clean rag. 2. Apply grease to the tri-roller shaft bearings and rear roller bearings (Figure 12) until pressure is felt. Important: Do not apply too much pressure or the grease seals will be permanently damaged. 3.
PAGE 6
Notes: 6
PAGE 7
Notes: 7
PAGE 8