Installation Instructions

ManualsBrandsToro ManualsAttachmentsThree Wheel Drive Kit, Greensmaster 3250-D

Printed in the USA

W 2005 by The Toro Company

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

3–Wheel Drive Kit

Greensmaster

)

3250–D

Model No. 04553

Form No. 3353–811 Rev B

Installation Instructions

Removing the Existing Wheel

1. Park the tractor on a level surface and set the parking

brake. Turn the ignition key to Off to stop the engine.

Remove the key.

Accidental starting of the engine could seriously

injure you or other bystanders.

Remove the key from the ignition switch before

you do any maintenance.

Caution

2. Lift the rear of the traction unit and remove the tire

assembly from the castor fork.

3. Remove the wheel hub assembly from the tire

assembly. Retain the lug nuts.

4. Remove the adapter plates from the castor fork.

5. Remove the grease fitting from the motor and hub

assembly (Fig. 1).

Figure 1

1. Motor and hub assembly

2. Grease fitting

3. Standard flangette

4. Bearing

5. Relube flangette

6. Setscrew

7. Adapter Plate

Assembling the Rear Wheel

1. Mount the tire assembly to the motor and hub

assembly with 4 lug nuts. Torque the lug nuts to 70–90

ft.-lb. (95–122 N⋅m). The valve stem should be on the

same side as the lug nuts.

2. Install the grease fitting in the hub assembly, pointing

it away from the tire.

3. Insert the flangettes and bearing onto the end of the

motor shaft as shown in Figure 1.

4. Position the motor hub, flangettes w/bearing, and tire

assembly into the castor fork. The ports on motor

should face to the rear.

5. Loosely secure the motor to the left, inside of the

castor fork with 2 socket head screws and 2 nuts.

6. Loosely secure the flangettes w/bearing and adapter

plate to the right inside of the castor fork with 3

screws, 3 locknuts, and a bearing tab. Position the

grease fitting on the flangette downward. Tighten

motor screws to 85 ft.-lb. (115 N⋅ m) and the flangette

screws to 30 ft.-lb. (41 N⋅m).

Figure 2

1. Bearing tab 2. Decal

7. Apply loctite (not supplied) to the bearing setscrews

and torque them to 80–100 in.-lb. (9–11 N⋅m).

Summary of content (4 pages)

PAGE 1
Form No. 3353–811 Rev B 3–Wheel Drive Kit Greensmaster) 3250–D Model No. 04553 Installation Instructions Removing the Existing Wheel Assembling the Rear Wheel 1. Park the tractor on a level surface and set the parking brake. Turn the ignition key to Off to stop the engine. Remove the key. 1. Mount the tire assembly to the motor and hub assembly with 4 lug nuts. Torque the lug nuts to 70–90 ft.-lb. (95–122 N⋅m). The valve stem should be on the same side as the lug nuts. Caution 2.
PAGE 2
8. Verify the overrunning bearing operation by checking that the tire rolls freely forward, but engages the wheel motor when rolled backwards. 9. Lower the rear of the traction unit to the ground. 10. Apply the decals to each side of the castor fork as shown in Figure 2. Installing the Hoses 1 1. Using the dimensions shown in Figure 3, locate, mark, and drill 4 holes (9/32 in. diameter) into the right-hand frame tube. 11 + 1/4 in. 11 + 1/4 in. 1 Figure 5 2. Hydrostat hose (upper) 1 + 1/16 in. 4.
PAGE 3
Installing the ROPS 8. Turn the steering fork fully side to side to check for proper hose flex and position. The hoses should not rub on the tanks, steering fork, or steering hoses. Note that the hose clamp brackets are slotted vertically to allow for adjustment. Secure the hoses in the brackets. 1. Lower the ROPS frame onto the mounting brackets, aligning the mounting holes as shown in Figure 8.
PAGE 4
FORWARD 4 P3 1500 LOW IDLE 2750 HIGH IDLE (DIESEL) R4 DUMP VALVE REAR WHEEL DRIVE MOTOR M4 M5 HYDROSTAT FRONT TRACTION WHEEL MOTORS ENGINE RPM R5 OPTIONAL KIT OIL COOLER OIL FILTER T S1 P1 P1 P2 FC1 01 GEAR PUMP R1 LC1 PT ST S2 OPTIONAL VALVES MB MA RD1 BACKLAP MOW M2 M3 REEL MOTORS P2 S3 M1 PB T P R2 V1 MANIFOLD BLOCK S4 L R .05 .05 POWER STEERING VALVE L2A L2B L1A L1B L3A L3B #2 .