Service Manual

ManualsBrandsToro ManualsRiding ProductsGreensmaster eTriFlex 3360 Traction Unit

Greensmaster 3360 and 3370 eTriFlex Diagnostic Fault Code Quick Reference Table  Page 1 of 52 
Greensmaster 3360 and 3370 eTriFlex Diagnostic Fault Code 
Quick Reference Table 
 
B1007 ...................................... 3 
B1197 ...................................... 3 
C0051 ..................................... 3 
C0526 ..................................... 3 
C0528 ..................................... 3 
C0529 ..................................... 4 
C1013 ..................................... 4 
C1014 ..................................... 5 
C1015 ..................................... 6 
C1023 ..................................... 6 
C1024 ..................................... 7 
C1025 ..................................... 7 
C10C4 ..................................... 7 
C10C5 ..................................... 8 
C10E3 ..................................... 8 
C10E4 ..................................... 8 
C10E5 ..................................... 9 
C1801 ..................................... 9 
C180C ..................................... 9 
C1811 ................................... 10 
C181C ................................... 10 
C1820 ................................... 10 
C1821 ................................... 10 
C1822 ................................... 11 
C1831 ................................... 11 
C1832 ................................... 11 
C1841 ................................... 11 
C1842 ................................... 12 
C1851 ................................... 12 
C1852 ................................... 12 
C1861 ................................... 12 
C1901 ................................... 13 
C190C ................................... 13 
C1910 ................................... 13 
C1912 ................................... 13 
C1919 ................................... 14 
C1921 ................................... 14 
C1922 ................................... 14 
C1931 ................................... 14 
C1932 ................................... 15 
C1941 ................................... 15 
C1942 ................................... 15 
C1A01 ................................... 16 
C1A11 ................................... 16 
C1A20 ................................... 16 
C1A22 ................................... 17 
C1A27 ................................... 17 
C1A32 ................................... 17 
C1A41 ................................... 18 
C1A55 ................................... 18 
C1A5C .................................. 18 
C1A5D .................................. 19 
C1A69 ................................... 19 
C1A6C .................................. 19 
C1A7D .................................. 19 
C1A7E ................................... 20 
P0524 .................................... 20 
P058E ................................... 20 
P058F ................................... 21 
P063C ................................... 21 
P063D ................................... 21 
P06E9 ................................... 22 
P0A1B ................................... 22 
P0A2A ................................... 22 
P0A2F ................................... 23 
P0A36 ................................... 23 
P0A3B ................................... 23 
P0A3C ................................... 23 
P0A3E ................................... 24 
P0A44 ................................... 24 
P0A54 ................................... 24 
P0A5A ................................... 24 
P0A5C ................................... 24 
P0A80 ................................... 25 
P0AA1 ................................... 25 
P0AA2 ................................... 25 
P0AC2 ................................... 26 
P0AE4 ................................... 26 
P0AE5 ................................... 26 
P0AE6 ................................... 26 
P0AFA ................................... 27 
P0AFB ................................... 27 
P0C06 ................................... 27 
P0C19 ................................... 28 
P0D2F ................................... 28 
P0D30 ................................... 28 
P0E8E ................................... 29 
P0E8F ................................... 29 
P1501 .................................... 29 
P1511 .................................... 30 
P1520 .................................... 30 
P1522 .................................... 30 
P1527 .................................... 31 
P1529 .................................... 31 
P152C ................................... 31 
P1531 .................................... 31 
P1532 .................................... 31 
P1541 .................................... 32 
P1542 .................................... 32 
P1554 .................................... 32 
P1555 .................................... 33 
P156C ................................... 33 
P156D ................................... 33 
P156E ................................... 34 
P1A01 ................................... 34 
P1A02 ................................... 34 
P1A11 ................................... 35 
P1A21 ................................... 35 
P1B01 ................................... 36 
P1B11 ................................... 36 
P1B20 ................................... 36 
P1B21 ................................... 36 
P1B2C ................................... 37 
P1B31 ................................... 37 
P1B41 ................................... 37 
P1B42 ................................... 37 
P1B4C ................................... 37 
P1B51 ................................... 38 
P1B6C ................................... 38 
P210E ................................... 38 
P2503 .................................... 38 
P2504 .................................... 39 
P2530 .................................... 39 
P2BE8 ................................... 39 
P2BE9 ................................... 40 
P2BEA .................................. 40 
U0110 ................................... 40 
U0111 ................................... 40 

Summary of content (52 pages)

PAGE 1
Greensmaster 3360 and 3370 eTriFlex Diagnostic Fault Code Quick Reference Table B1007...................................... 3 B1197...................................... 3 C0051 ..................................... 3 C0526 ..................................... 3 C0528 ..................................... 3 C0529 ..................................... 4 C1013 ..................................... 4 C1014 ..................................... 5 C1015 ..................................... 6 C1023 ............
PAGE 2
U0120 ................................... 41 U012A ................................... 41 U0131 ................................... 41 U0156 ................................... 42 U0292 ................................... 42 U029B ................................... 42 U0320 ................................... 42 U1011 ................................... 42 U1012 ................................... 43 U1012 ................................... 43 U1025 ................................... 43 U110C ..........
PAGE 3
Fault Fault Title Controller(s) Fault Condition/Circuit Number Affected Description B1007 Joystick T1 This fault is reported when Raise/Lower Broken the joystick lower and joystick raise inputs are active at the same time. B1197 Mode Switch Broken C0051 Additional Notes 1) Service Actions The machine will not be capable of a raise or a lower, depending on which switch failed. 1) Test the joystick switches with the InfoCenter. 2) Inspect and test the joystick wiring and connectors (P01, P04, P05).
PAGE 4
Fault Fault Title Number C0529 Steering Angle Sensor Signal Correlation Fault C1013 ETR/RTR/OK to Run - Short to Battery Controller(s) Fault Condition/Circuit Additional Notes Affected Description SC7 This fault is reported when The traction motors are the sum of the 2 signals on disabled. the rear angle sensor are not correlating correctly. T1 This fault is reported when low current is detected on the Engine Control signal, indicating a short to a high (+) source.
PAGE 5
Fault Fault Title Number C1014 ETR/RTR/OK to Run - Short to Ground/Overcurrent Controller(s) Fault Condition/Circuit Affected Description T1 This fault is reported when overcurrent is detected on the Engine Control signal, indicating a short to ground. Additional Notes The circuit starts at P01 pin 10. Greensmaster 3360 and 3370 eTriFlex Diagnostic Fault Code Quick Reference Table 1) Service Actions 1) Test the circuit wiring to ground.
PAGE 6
Fault Fault Title Number C1015 ETR/RTR/OK to Run - Open The Circuit C1023 Park Brake Disengage - Short to Battery Controller(s) Fault Condition/Circuit Affected Description T1 This fault is reported when an open circuit is detected on the Engine Control signal. T1 This fault is reported when low current is detected on the automatic Parking Brake Off signal, indicating a short to a high (+) source. Additional Notes The circuit starts at P01 pin 10.
PAGE 7
Fault Fault Title Controller(s) Fault Condition/Circuit Number Affected Description C1024 Park Brake T1 This fault is reported when Disengage - Short to overcurrent is detected on Ground/Overcurrent the automatic Parking Brake Off signal, indicating a short to ground. C1025 Park Brake Disengage - Open Circuit C10C4 Steering Wheel Feel Output - Short to Ground/Overcurrent Additional Notes 1) Service Actions Short circuit between the 1) Test the circuit wiring to ground.
PAGE 8
Fault Fault Title Controller(s) Fault Condition/Circuit Number Affected Description C10C5 Steering Wheel Feel T1 This fault is reported when Output - Open an open circuit is detected Circuit on the Steering Feedback signal. C10E3 48V Logic Enable Short to Battery T1 This fault is reported when low current is detected on the Logic Relay signal, indicating a short to a high (+) source.
PAGE 9
Fault Fault Title Number C10E5 48V Logic Enable Open Circuit C1801 Controller(s) Fault Condition/Circuit Affected Description T1 This fault is reported when an open circuit is detected on the Logic Relay signal. Cutting Unit Motor High Temp Shutdown T2 T3 T4 C180C Cutting Unit Motor High Temp Warning T2 T3 T4 Additional Notes 1) Service Actions The circuit starts at P01 pin 08. 1) Test the output circuit wiring to the component connected.
PAGE 10
Fault Fault Title Number C1811 Cutting Unit Motor Controller - High Temp Shutdown Controller(s) Fault Condition/Circuit Additional Notes Affected Description T2 This fault is reported when Disables the PTO. T3 the motor controller T4 temperature is greater than 100 °C (212 °F) in the indicated cutting unit.
PAGE 11
Fault Fault Title Number C1822 Cutting Unit Motor Stall Controller(s) Fault Condition/Circuit Affected Description T2 This fault is reported when T3 the speed of the motor in T4 the indicated cutting unit is 0 RPM for more than 3 seconds.
PAGE 12
Fault Fault Title Number C1842 Cutting Unit Motor Logic Voltage - Low Controller(s) Fault Condition/Circuit Affected Description T2 This fault is reported when T3 the indicated cutting unit T4 measures the 48V logic voltage at less than 32V. C1851 Cutting Unit Motor Bus Voltage - High T2 T3 T4 This fault is reported when the indicated cutting unit measures the 48V bus voltage at greater than 67.5V.
PAGE 13
Fault Fault Title Number C1901 Lift/Lower Motor Controller - High Temp Shutdown Controller(s) Fault Condition/Circuit Affected Description SC2 This fault is reported when SC3 the temperature of the SC4 indicated actuator is greater than 75 °C (167 °F). Additional Notes Disables lift/lower. C190C Lift/Lower Motor Controller - High Temp Warning SC2 SC3 SC4 This fault is reported when the temperature of the indicated actuator is greater than 65 °C (149 °F).
PAGE 14
Fault Fault Title Number C1919 Lift/Lower Motor Position Error C1921 C1922 C1931 Lift/Lower Motor Logic Voltage - High Lift/Lower Motor Logic Voltage - Low Lift/Lower Motor Bus Voltage - High Controller(s) Fault Condition/Circuit Affected Description SC2 This fault is reported when SC3 an internal sensor fails in SC4 the indicated actuator. Additional Notes Disables lift/lower. SC2 SC3 SC4 This fault is reported when the indicated actuator measures the 48V logic voltage at greater than 67.5V.
PAGE 15
Fault Fault Title Controller(s) Fault Condition/Circuit Number Affected Description C1932 Lift/Lower Motor Bus SC2 This fault is reported when Voltage - Low SC3 the indicated actuator SC4 measures the 48V bus voltage at less than 32V. Additional Notes Disables lift/lower. Note: If more than one Bus Voltage - Low faults are reported, go to fault U1512 and follow the listed service actions.
PAGE 16
Fault Fault Title Number C1A01 Steering Motor High Temp Shutdown Controller(s) Fault Condition/Circuit Affected Description SC7 This fault is reported when the temperature of the steering motor is greater than 120 °C (248 °F). Additional Notes 1) Service Actions The traction motors are disabled, and steering is disabled. 1) Check for extra mechanical load on the steering unit assembly. 2) Allow steering unit assembly to cool down. 3) If the fault repeats, replace the steering unit assembly.
PAGE 17
Fault Fault Title Number C1A22 Steering Motor Stall Controller(s) Fault Condition/Circuit Additional Notes Affected Description SC7 This fault is reported when The traction motors are the steering motor draws disabled, and steering is too much current for too disabled. long (longer than 1 second when the traction speed is higher than 15%, or longer than 5 seconds when the traction speed is lower than 5%).
PAGE 18
Fault Fault Title Number C1A41 Steering Controller Over Current C1A55 Controller(s) Fault Condition/Circuit Additional Notes Affected Description SC7 This fault can be reported The traction motors are when a current sensor fails disabled, and steering is in the controller of the disabled. steering unit assembly, or when actual high current is detected for an extended period of time.
PAGE 19
Fault Fault Title Number C1A5D Steering Motor Phase W - Open Circuit C1A69 Steering Wheel Sensor - Feedback Noisy Controller(s) Fault Condition/Circuit Affected Description SC7 This fault is reported when the controller in the steering unit assembly detects an open circuit on motor phase W. Additional Notes 1) Service Actions The traction motors are disabled, and steering is disabled. 1) Test the 30A, 48V bus standard blade fuse (under the operator’s seat) and the power connection to the 48V battery.
PAGE 20
Fault Fault Title Controller(s) Fault Condition/Circuit Number Affected Description C1A7E Steering Motor SC7 This fault is reported when Software - Hardware the software is not Incompatibility compatible with the hardware. P0524 Oil Pressure Low Kill Engine P058E Battery - High Temp Shutdown T1 SC8 Additional Notes 1) Service Actions The traction motors are disabled, and steering is disabled. 1) Use Toro DIAG to reprogram the machine. 2) Replace the steering unit assembly.
PAGE 21
Fault Fault Title Number P058F Battery - Low Temp Shutdown Controller(s) Fault Condition/Circuit Affected Description SC8 The BMS controller reported to the TEC-5004 controller (T1) that the temperature of one or more batteries was less than -20 °C (-4 °F), and then shut off power to the machine. P063C Generator Logic Voltage - Low T6 This fault is reported when the starter/generator measures the 48V logic voltage at less than 36V.
PAGE 22
Fault Fault Title Number P06E9 Starter Timeout P0A1B Traction Controller Short P0A2A Traction Motor Temperature Sensor Failure Controller(s) Fault Condition/Circuit Affected Description T1 This fault is reported when the primary controller (T1) detects that the starter was engaged for more than the maximum permitted crank time. This fault could be caused by the key switch being held in the Start position for more than 15 seconds, or by the key switch and/or its wiring being defective.
PAGE 23
Fault Fault Title Number P0A2F Traction Motor High Temp Warning P0A36 Generator Temperature Sensor Failure P0A3B Generator Motor High Temp Warning P0A3C Traction Motor Controller - High Temp Warning Controller(s) Fault Condition/Circuit Affected Description SC5 This fault is reported when SC6 the motor temperature in T5 the indicated drive unit is greater than: 150 °C (302 °F) for SC5, SC6 (Zapi) 120 °C (248 °F) for T5 (Toro): T6 This fault is reported when the FET sensor and the motor sensor fail.
PAGE 24
Fault Fault Title Controller(s) Fault Condition/Circuit Number Affected Description P0A3E Generator Controller T6 This fault is reported when - High Temp the controller temperature Warning is greater than 90 °C (194 °F).
PAGE 25
Fault Fault Title Number P0A80 Battery - Internal Hardware Failure Controller(s) Fault Condition/Circuit Affected Description SC8 This fault is reported when a hardware component in one or more Samsung batteries has failed. P0AA1 Battery Contactor Stuck Closed SC8 This fault is reported when the battery contactor inside the Samsung BMS controller is measured to be closed when it should be open.
PAGE 26
Fault Fault Title Number P0AC2 Battery - Over Current Controller(s) Fault Condition/Circuit Affected Description SC8 This fault is reported when a battery is supplying too much current for too long. This can be caused by too much power draw or by a defective battery.
PAGE 27
Fault Fault Title Number P0AFA Battery - Low Voltage Controller(s) Fault Condition/Circuit Affected Description SC8 This fault is reported when the voltage of a cell inside one of the batteries was measured to be too low but the battery may be recoverable via software or by using the battery charger. P0AFB Battery - High Voltage SC8 This fault is reported when the voltage of a cell inside one of the batteries was measured to be too high.
PAGE 28
Fault Fault Title Number P0C19 Traction Motor Power Mismatch P0D2F Traction Motor Logic Voltage - Low P0D30 Traction Motor Logic Voltage - High Controller(s) Fault Condition/Circuit Additional Notes Affected Description SC5 This fault is reported when The controller loses the SC6 the motor in the indicated ability to control the drive unit is not responding motor. to the power setpoint. The traction motors are disabled.
PAGE 29
Fault Fault Title Number P0E8E Traction Motor Bus Voltage - Low Controller(s) Fault Condition/Circuit Affected Description SC5 This fault is reported when SC6 the motor in the indicated T5 drive unit measures the 48V bus voltage at less than 32V for T5 (Toro), or 38V for SC5, SC6 (Zapi). P0E8F Traction Motor Bus Voltage - High SC5 SC6 T5 P1501 Traction Motor High Temp Shutdown SC5 SC6 T5 Additional Notes 1) Service Actions The traction motors are disabled.
PAGE 30
Fault Fault Title Number P1511 Traction Motor Controller - High Temp Shutdown Controller(s) Fault Condition/Circuit Additional Notes Affected Description T5 This fault is reported when The traction motors are the controller temperature disabled.
PAGE 31
Fault Fault Title Number P1527 Traction Motor Speed Sensor Data Invalid P1529 Traction Motor Speed Sensor Wrong Direction P152C Traction Motor Speed Sensor Feedback Noisy Controller(s) Fault Condition/Circuit Affected Description SC5 This fault is reported when SC6 the speed sensor reading in the indicated drive unit is invalid. SC5 This fault is reported when SC6 the speed sensor in the indicated drive unit shows the motor moving in the wrong direction.
PAGE 32
Fault Fault Title Number P1541 Traction Motor Phase - Voltage High Controller(s) Fault Condition/Circuit Affected Description SC5 This fault is reported when SC6 the motor phase voltage in the indicated drive unit is out-of-range high. Additional Notes The traction motors are disabled. P1542 Traction Motor Phase - Voltage Low SC5 SC6 This fault is reported when The traction motors are the motor phase voltage in disabled. the indicated drive unit is out-of-range low.
PAGE 33
Fault Fault Title Number P1555 Traction Motor Contactor Coil Open Circuit Controller(s) Fault Condition/Circuit Affected Description SC5 This fault is reported when an open circuit is detected on the NMC signal from the controller. Additional Notes The traction motors are disabled. The circuit starts at P35, pin 12. P156C Traction Controller Internal Hardware Failure SC5 SC6 This fault is reported when an internal component of controller fails in the indicated drive unit.
PAGE 34
Fault Fault Title Controller(s) Fault Condition/Circuit Number Affected Description P156E Traction Motor SC5 This fault is reported when Software - Hardware SC6 the software in the Incompatibility indicated drive unit is not compatible with the hardware. P1A01 Battery Charging High Temp Shutdown SC8 This fault is reported when a battery temperature was measured to be greater than 60 °C (140 °F) and the battery controller will not allow it to be charged.
PAGE 35
Fault Fault Title Number P1A11 Battery Charging Voltage - High P1A21 Battery Charging Over Current Controller(s) Fault Condition/Circuit Affected Description SC8 This fault is reported when a battery cell voltage was measured to be higher than the allowed threshold while the battery charger was connected. The battery controller will not allow it to be charged. SC8 Additional Notes This fault is reported when a battery cell charging current was measured to be greater than the allowed threshold.
PAGE 36
Fault Fault Title Number P1B01 Generator Motor High Temp Shutdown Controller(s) Fault Condition/Circuit Affected Description T6 This fault is reported when the motor temperature is greater than 130 °C (266 °F). Additional Notes Disables the PTO and disables the starter/generator. Note: This fault is not produced by a bad sensor.
PAGE 37
Fault Fault Title Number P1B2C Generator Motor Stall Controller(s) Fault Condition/Circuit Additional Notes Affected Description T6 This fault is reported when Disables the PTO and the starter/generator motor disables the stalls for 3 seconds or starter/generator. more. P1B31 Generator Motor Internal Regulator Voltage - High T6 This fault is reported when the internal regulator voltage is greater than 18V.
PAGE 38
Fault Fault Title Controller(s) Fault Condition/Circuit Number Affected Description P1B51 Generator Hardware T6 This fault is reported when Phase Over Current the current sensor on phase current indicates an internal short. P1B6C Generator Internal T6 This fault is reported when Hardware Failure the hardware phase overcurrent and hardware overvoltage trip. P210E Traction Pedal 1 SC5 This fault is reported when Sensor/Switch the traction pedal sensor Analog vs Analog reports different positions.
PAGE 39
Fault Fault Title Number P2504 Alternator Charging Too High Controller(s) Fault Condition/Circuit Affected Description T1 This fault is reported when the TEC senses that the 12V charging system is greater than 16.3V. Note: The alternator consists of a stator coil, flywheel magnets, and an external voltage regulator Additional Notes Note: One 12V AGM battery, an alternator (stator coil and flywheel magnets), and an external voltage regulator combine to provide the 12V system electrical power.
PAGE 40
Fault Fault Title Number P2BE9 Traction Motor Contactor - Closed P2BEA Traction Motor Precharge Failure Controller(s) Fault Condition/Circuit Additional Notes Affected Description SC5 This fault is reported when The traction motors are traction motor contactor is disabled. detected closed when it should be open. SC5 This fault is reported when The traction motors are SC6 there is a short on the 48V disabled. traction bus or too much resistance or capacitance in the indicated drive unit.
PAGE 41
Fault Fault Title Number U0120 CAN Bus Communication Fault - Generator Controller(s) Fault Condition/Circuit Additional Notes Affected Description T1 This fault is reported when Disables the PTO and the primary controller the starter/generator. never establishes or loses communication with the starter/generator controller. U012A CAN Bus Communication Fault - Precharge T1 This fault is reported when the primary controller (T1) never establishes or loses communication with the precharge controller (T6).
PAGE 42
Fault Fault Title Number U0156 CAN Bus Communication Fault - IC Controller(s) Fault Condition/Circuit Affected Description T1 This fault is reported by the primary controller (T1) if it never establishes or loses communication with the InfoCenter. This fault may also be reported by the InfoCenter if the primary controller(T1) loses 12V logic power.
PAGE 43
Fault Fault Title Number U1012 Controller Logic Voltage Low Controller(s) Fault Condition/Circuit Affected Description T1 The primary controller (T1) is reporting that it is measuring the logic voltage as less than 8.8V. U1012 Controller Logic Voltage Low T6 The precharge controller (T6) is reporting that it is measuring the logic voltage as less than 32V. U1025 TEC Fuse 5 Failure T1 This fault is reported when the fuse has failed for outputs 13–16 on the primary controller (T1).
PAGE 44
Fault Fault Title Number U1121 48V Devices Offline Controller(s) Fault Condition/Circuit Affected Description T1 This fault is reported when the primary controller (T1) on CAN bus A cannot communicate with any of the 48V devices, which are all on CAN bus B. Additional Notes PTO and starter/generator are disabled. 1) Service Actions 1) Verify that the 48V battery disconnect is plugged in. 2) Inspect CAN bus isolation module connector and harness connector P50 for damage and corrosion.
PAGE 45
Fault Fault Title Number U1128 CAN Bus Communication Fault - Lift/Lower Motor 1 Controller(s) Fault Condition/Circuit Affected Description T1 This fault is reported when the primary controller (T1) never establishes or loses communication with lift/lower actuator 1. U1129 CAN Bus Communication Fault - Lift/Lower Motor 2 T1 This fault is reported when the primary controller never establishes or loses communication with lift/lower actuator 2.
PAGE 46
Fault Fault Title Number U1301 Software Version Incompatibility - CU Motor 1 U1302 Software Version Incompatibility - CU Motor 2 U1303 Software Version Incompatibility - CU Motor 3 U1304 Software Version Incompatibility Lift/Lower Motor 1 U1305 Software Version Incompatibility Lift/Lower Motor 2 U1306 Software Version Incompatibility Lift/Lower Motor 3 U1307 Software Version Incompatibility Generator U1308 Software Version Incompatibility Precharge Controller U130A Software Version Incompatibility InfoCent
PAGE 47
Fault Fault Title Controller(s) Fault Condition/Circuit Number Affected Description U130D Software Version T1 This fault is reported when Incompatibility the rear drive unit firmware Traction Motor 3 is incompatible. U130E Software Version SC5 This fault is reported when Incompatibility SC6 the software in the Processor Mismatch SC7 indicated component is incompatible.
PAGE 48
Fault Fault Title Number U1501 48V System Logic Voltage - High Controller(s) Fault Condition/Circuit Affected Description T1 This fault is reported when 3 or more components on the machine are reporting a Logic Voltage - High fault. Additional Notes PTO is disabled and the starter/generator won't generate. Note: This fault may be dependent upon how aggressive the operator is driving the machine.
PAGE 49
Fault Fault Title Number U1502 48V System Logic Voltage - Low Controller(s) Fault Condition/Circuit Affected Description T1 This fault is reported when 3 or more components on the machine are reporting a Logic Voltage - Low fault. Additional Notes PTO is disabled. 1) Service Actions For the 3360 only: 1) Test the 100A BF1 style fuse (under the operator’s seat). 2) Test the 5A standard blade fuse (under the operator’s seat) 3) Inspect and test the 48V battery pack.
PAGE 50
Fault Fault Title Number U1511 48V System Bus Voltage - High Controller(s) Fault Condition/Circuit Affected Description T1 This fault is reported when 3 or more components on the machine are reporting a Bus Voltage - High fault. Additional Notes PTO is disabled. 1) Service Actions For the 3360 only: 1) Test the starter/generator. 2) Inspect the wiring between the starter/generator and the controller. 3) Install a replacement starter/generator assembly into the machine.
PAGE 51
Fault Fault Title Number U1512 48V System Bus Voltage - Low Controller(s) Fault Condition/Circuit Affected Description T1 This fault is reported when 3 or more components on the machine are reporting a Bus Voltage - Low fault. Additional Notes PTO is disabled. 1) Service Actions For the 3360 only: 1) Test the 100A BF1 style fuse (under the operator’s seat). 2) Test the 5A standard blade fuse (under the operator’s seat) 3) Inspect and test the 48V battery pack.
PAGE 52
Fault Fault Title Number U1700 Board Internal Error U1701 Board Internal Error - IPE Controller(s) Fault Condition/Circuit Affected Description T6 The precharge controller (T6) has a power/ground problem or an internal failure. T1 This fault is reported when inputs or outputs in the primary controller are not working correctly. Additional Notes Disables the machine.