Form No. 3351-564 Rev. A 8 and 11 Blade DPA Reel Mowers Greensmaster 3000 Series Model No. 04610—Serial No. 240000001 and Up Model No. 04611—Serial No.
Contents Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . General Specifications . . . . . . . . . . . . . . . . . . . . . Optional Equipment . . . . . . . . . . . . . . . . . . . . . . . . Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Loose Parts Chart . . . . . . . . . . . . . . . .
Specifications General Specifications Tractors These cutting units will mount on the Greensmaster 3000, Greensmaster 3000–D, Greensmaster 3050, Greensmaster 3100, Greensmaster 3150, and Greensmaster 3250–D. Height of Cut Cutting height is adjusted on the front roller by two vertical screws and held by two locking capscrews. Height Of Cut Range Standard bench height of cut range is .062 inch (1.6 mm) to .500 inches (12.7 mm). Bench height of cut range with the High Height of Cut Kit installed is .
Optional Equipment High Cut Bedknife Part No. 94–6392 Low Cut Bedknife Part No. 93–4264 Micro–Cut Bedknife Part No. 93–4262 Fairway Bedknife Part No. 63–8600 Full Roller (Set of three) Model No.
1. The cutting unit is shipped without a front roller. Install the roller using the loose parts supplied with the cutting unit and installation instructions included with the roller. Note: An optional Lift Hook, Toro Part No. 106-6938 may be used in place of the chain link, if desired (Fig. 2). It may be obtained from your local Toro Distributor.
B. On right end of cutting unit, remove plastic plug from bearing housing (Fig. 6). G. Install the counter weight to the right end of the cutting unit with the screws previously removed. C. Remove the 2 allen head screws securing the motor mount to the right end of the cutting unit. Remove the motor mount (Fig. 6). 3 2 1 Figure 6 1. Motor mount 2. Plastic plug 3. Allen head screw (2) D. Remove the snap ring securing the drive coupler in the reel tube (Fig. 7). Remove the drive coupler.
Adjustments Note: Each time adjusting screw is rotated one click clockwise, bedknife moves .0007 in. closer to reel. Do not overtighten the adjusting screws. After the cutting unit is unboxed, use the following procedures to ensure that the cutting units are adjusted properly. 4. Check for light contact at other end of reel using paper and adjust as required. 5.
Adjusting the Height of Cut 2. To adjust rear roller proceed as follows: • Raise rear of cutting unit and place a block under bedknife. Note: For heights of cut greater than .500“, the high height of cut kit must be installed • Remove (2) nuts securing each roller bracket and spacer to each sideplate mounting flange. 1. Loosen locknuts securing height-of-cut arms to cutting unit side plates (Fig. 13). • Lower roller and screws from sideplate mounting flanges and spacers.
Adjusting the Cut-Off Bar Adjust cut–off bar to assure clippings are cleanly discharged from the reel area: 1. Loosen screws securing top bar (Fig. 16) to cutting unit. Figure 15 1 4. Rotate adjusting screw until roller contacts front of gauge bar. Adjust both ends of roller until entire roller is parallel to the bedknife. Important When set properly, the rear and front rollers will contact the gauge bar and the screw will be snug against the bedknife.
Operation Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Note: Determine the left and right sides of the machine from the normal operating position. Cutting Unit Characteristics Servicing the Bedbar The dual knob bedknife-to-reel adjustment system incorporated in this cutting unit simplifies the adjustment procedure needed to deliver optimum mowing performance.
1. Position the machine on a clean, level surface, lower the cutting units, stop the engine, engage the parking brake, and remove the ignition key. 3 2. Remove the reel motors from the cutting units and disconnect and remove the cutting units from the lift arms. 3. Connect the backlapping machine to the cutting unit by inserting a piece of 3/8 in. square stock into the splined coupling at the right end of the cutting unit.
The Toro General Commercial Products Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial Product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first.
