Form No. 3328–789 Rev. A 8 and 11 Blade DPA Reel Mowers Greensmaster 3000 Series Model No. 04610—Serial No. 230000001 and Up Model No. 04611—Serial No.
Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . General Specifications . . . . . . . . . . . . . . . . . . . . . Optional Equipment . . . . . . . . . . . . . . . . . . . . . . . Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Loose Parts Chart . . . . . . . . . . . . . . . . . . . . . . . . . Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications General Specifications Tractors These cutting units will mount on the Greensmaster 3000, Greensmaster 3000–D, Greensmaster 3050, Greensmaster 3100, Greensmaster 3150, and Greensmaster 3250–D. Height of Cut Cutting height is adjusted on the front roller by two vertical screws and held by two locking capscrews. Height Of Cut Range Standard bench height of cut range is .062 inch (1.6 mm) to .375 inches (9.5 mm). Bench height of cut range with the High Height of Cut Kit installed is .
Optional Equipment High Cut Bedknife Part No. 94–6392 Low Cut Bedknife Part No. 93–4264 Micro–Cut Bedknife Part No. 93–4262 Fairway Bedknife Part No. 63–8600 Full Roller (Set of three) Model No.
Setup Note: Determine the left and right sides of the machine from the normal operating position. Loose Parts Chart Note: Use this chart as a checklist to ensure all parts necessary for assembly have been shipped. If any of these parts are missing, total setup cannot be completed. Description Qty.
Important Whenever the cutting unit has to be tipped to expose bedknife/reel, prop up rear of cutting unit to make sure nuts on back end of bedbar adjusting screws are not resting on work surface (Fig. 4). 3 1 2 1 Figure 6 2 1. Motor mount 2. Plastic plug 3. Allen head screw (2) Figure 4 1. Prop (not provided) 2. Bedknife adjusting screw nut (2) D. Remove the snap ring securing the drive coupler in the reel tube (Fig. 7). Remove the drive coupler. 4.
Adjustments Note: Each time adjusting screw is rotated one click clockwise, bedknife moves .0007 in. closer to reel. Do not overtighten the adjusting screws. After the cutting unit is unboxed, use the following procedures to ensure that the cutting units are adjusted properly. 4. Check for light contact at other end of reel using paper and adjust as required. 5.
Adjusting the Height of Cut 2. To adjust rear roller proceed as follows: • Raise rear of cutting unit and place a block under bedknife. Note: For heights of cut greater than .375“, the high height of cut kit must be installed • Remove (2) nuts securing each roller bracket and spacer to each sideplate mounting flange. 1. Loosen locknuts securing height-of-cut arms to cutting unit side plates (Fig. 13). • Lower roller and screws from sideplate mounting flanges and spacers.
Adjusting the Cut-Off Bar 3. Hook screw head on cutting edge of bedknife and rest rear end of bar on rear roller (Fig. 15). Adjust cut–off bar to assure clippings are cleanly discharged from the reel area: 1. Loosen screws securing top bar (Fig. 16) to cutting unit. 1 Figure 15 4. Rotate adjusting screw until roller contacts front of gauge bar. Adjust both ends of roller until entire roller is parallel to the bedknife.
Operation Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Note: Determine the left and right sides of the machine from the normal operating position. Cutting Unit Characteristics Servicing the Bedbar The dual knob bedknife-to-reel adjustment system incorporated in this cutting unit simplifies the adjustment procedure needed to deliver optimum mowing performance.
Backlapping the Reel 3 Danger Contact with the reel or other moving parts can result in personal injury. 4 Keep fingers, hands, and clothing away from the reels or other moving parts. 4 • Stay away from the reel while backlapping. • Never use a short handled paint brush for backlapping. Part No. 29-9100 Handle assembly complete or individual parts are available from your local Authorized Toro Distributor. 3 2 1 1.
The Toro General Commercial Products Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your 1996 or newer Toro Commercial Product (“Product”) purchased after January 1, 1997, to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first.
