Form No. 3367-431 Rev B 8, 11, and 14 Blade DPA Reel Mower Greensmaster® 3000 Series Model No. 04610—Serial No. 311000001 and Up Model No. 04611—Serial No. 311000001 and Up Model No. 04616—Serial No. 311000001 and Up To register your product or download an Operator's Manual or Parts Catalog at no charge, go to www.Toro.com.
Introduction Figure 2 Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely. 1. Safety alert symbol This manual uses 2 other words to highlight information. Important calls attention to special mechanical information and Note emphasizes general information worthy of special attention. You may contact Toro directly at www.Toro.
Safety advisable and required by some local ordinances and insurance regulations. Hazard control and accident prevention are dependent upon the awareness, concern, and proper training of the personnel involved in the operation, transport, maintenance, and storage of the machine. Improper use or maintenance of the machine can result in injury or death. To reduce the potential for injury or death, comply with the following safety instructions.
Setup Media and Additional Parts Description Use Qty. Ball stud 2 Mount to roller Operator’s Manual 1 Read before installing and operating cutting unit Parts catalog 1 Use to reference part numbers Certification of compliance 1 1 1 Installing the Front Roller No Parts Required Procedure The cutting unit is shipped without a front roller. Install the roller using the loose parts supplied with the cutting unit and installation instructions included with the roller. g014745 Figure 3 2 1.
3 Using the Cutting Unit Prop No Parts Required Procedure Whenever the cutting unit has to be tipped to expose the bedknife/reel, prop up the rear of the cutting unit to make sure the nuts on the back end of the bedbar adjusting screws are not resting on the work surface (Figure 6). Figure 4 1. Offset lift hook The Chain Link, part no. 106-2601, mounting bracket, part no. 105-5738 and (2) capscrews, part no. 323-6 may also be used on the Greensmaster 3250-D traction unit.
Figure 9 Figure 7 1. Snap ring 2. Drive coupler 1. Counter weight 5. Apply grease to the inside diameter of the drive coupler. Install the drive coupler to the left end of the cutting unit reel tube with a snap ring (Figure 9). 2. On the right end of the cutting unit, remove the plastic plug from the bearing housing (Figure 8). 6. Install the motor mount to the left end of the cutting unit with the (2) Allen head screws previously removed in Figure 8. Torque screws to 12-15 ft-lbs. (16-20 N-m). 3.
drag be evident, it will be either necessary to backlap or regrind the cutting unit to achieve the sharp edges needed for precision cutting (see the Toro Reel Sharpening Manual). 6 Figure 10 Adjusting the Rear Roller 1. Bedbar adjusting screw 2. Tilt the mower on back to expose the bedknife and reel. No Parts Required Important: Make sure nuts on back end of bedbar adjusting screws are not resting on work surface (Figure 6). 3.
2. To adjust rear roller proceed as follows: 7 • Raise the rear of the cutting unit and place a block under the bedknife. • Remove the (2) nuts securing each roller bracket and spacer to each sideplate mounting flange. Adjusting the Height of Cut • Lower the roller and screws from the sideplate mounting flanges and spacers. No Parts Required • Place the spacers onto the screws on the roller brackets. Procedure Note: For heights of cut greater than .
3. Hook the screw head onto the cutting edge of the bedknife and rest the rear end of the bar onto the rear of the roller (Figure 17). Recommended Bedknife/Height of Cut Chart (cont'd.) High-cut (Optional) 94-6392 .312-1.00 inch (7.9-25.4 mm) Fairway (Optional) 63-8600 .375-1.00 inch (9.5-25.4 mm) 8 Adjusting the Cut-Off Bar No Parts Required Figure 17 Procedure 1. Gauge bar Adjust the cut-off bar to assure the clippings are cleanly discharged from the reel area: 4.
Product Overview Specifications Tractors These cutting units will mount on the Greensmaster 3000, 3000–D, 3050, 3100, 3150, 3250–D and 3150-Q Traction Units. Height of Cut Cutting height is adjusted on the front roller by two vertical screws and held by two locking cap screws Height Of Cut Range Standard bench height of cut range is .062 inch (1.6 mm) to .500 inch (12.7 mm). Bench height of cut range with the High Height of Cut Kit installed is .285 inch (7 mm) to 1.00 inch (25 mm).
Operation bedknife. If a file is occasionally run across the front edge to remove this burr, improved cutting can be obtained. After extended running, a ridge will eventually develop at both ends of the bedknife. These notches must be rounded off or filed flush with the cutting edge of the bedknife to ensure smooth operation Note: Determine the left and right sides of the machine from the normal operating position.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Servicing the Bedbar Removing the Bedbar 1. Turn bedbar adjuster screw, counterclockwise, to back bedknife away from reel (Figure 19). Figure 21 1. Bedbar bolt 2. Nut 3. Steel washer 4. Nylon washer Assembling the Bedbar 1. Install the bedbar, positioning the mounting ears between the washer and bedbar adjuster. Figure 19 1. Bedbar adjusting screw 2. Spring tension nut 2.
Backlapping the Reel DANGER Contact with the reel or other moving parts can result in personal injury. Keep fingers, hands, and clothing away from the reels or other moving parts. • Stay away from the reel while backlapping. • Never use a short handled paint brush for backlapping. Part No. 29-9100 Handle assembly complete or individual parts are available from your local Authorized Toro Distributor. 1.
Notes: 14
Notes: 15
The Toro Total Coverage Guarantee A Limited Warranty Conditions and Products Covered The Toro® Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
