Installation Instructions

ManualsBrandsToro ManualsAttachmentsDampening Roller Kit, DPA Cutting Units for Riding Greensmaster Tractors

FormNo.3359-412RevA

DampeningRollerKit

DPACuttingUnitsforRidingGreensmaster

Tractors

ModelNo.04629

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

Thisproductcontainsachemicalorchemicals

knowntotheStateofCaliforniatocausecancer,

birthdefects,orotherreproductiveharm.

Important:Usecautionwhenhandlingrollerassembly.

Donotdroptherollerassemblyontheshaftends.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

WidWiehleroller1

Height-of-cutarm

Installthefrontroller.

Rearroller1

Rollerretainer2

Shortbolt

Longbolt2

Rollerspacerassembly2

Flangenut6

Rollershim2

Installtherearroller.

Nopartsrequired

–

Installrearweight.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

*3359-412*A

Summary of content (8 pages)

PAGE 1
Form No. 3359-412 Rev A Dampening Roller Kit DPA Cutting Units for Riding Greensmaster® Tractors Model No. 04629 Installation Instructions Important: Use caution when handling roller assembly. Do not drop the roller assembly on the shaft ends. WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.
PAGE 2
Installing the Front Roller Installing the Rear Roller 1. Remove the cutting unit from the traction unit and place it on a stable work surface. 1. Raise the rear of the cutting unit and place a block under the bedknife. 2. Remove the plow bolts, washers, and flange nuts securing the height-of-cut arms to the cutting unit side plates (Figure 1). 2. Remove the 2 nuts securing each roller clamp, bracket, and spacer to each sideplate mounting flange (Figure 2). Remove all components but retain the shims.
PAGE 3
4 3 4 2 3 2 1 1 g019719 Figure 3 Up to 0.437 inch (11 mm) height of cut 1. Roller spacer assembly g019721 Figure 5 0.625 to 1.00 inch (15.8 to 25.4 mm) height of cut 3. Shim 2. Side plate mounting flange 4. Roller spacer 1. Roller spacer assembly 3. Shim 2. Roller spacer 4. Side plate mounting flange 4. Adjust the cutting unit to the desired height of cut and tighten the height-of-cut arm mounting fasteners.
PAGE 4
Maintenance Disassembling and Assembling the Roller If you need to clean or replace the seals and bearings on the roller, use the following procedures to disassemble and assemble the dampening rollers. 9 6 2 3 4 5 1 7 8 g019722 Figure 6 1. Roller shaft assembly 4. Seal 7. Net sleeve 2. Bearing locknut 5. Ball bearing 8. Weight 3. V-ring 6. Roller tube 9. Seal installation tool Disassembling a Dampening Roller 5. Clean the bearing cavity in the roller and remove any rust with a crocus cloth.
PAGE 5
6 4 5 3 2 1 2 1 7 g019723 8 Figure 7 1. Roller shaft assembly 5. Ball bearing 2. Bearing locknut 6. Roller tube 3. Seal installation tool 7. 0.210 inch (5.3 mm) both ends 8. 2x press flush 4. Seal g019724 Figure 8 1. Bearing locknut 2. Position a new bearing onto each end of the roller shaft and push until the bearings are seated into each end of the roller (Figure 7). 2. V-ring 8. Lubricate the lips of the installed seals with #2 grease.
PAGE 6
Notes: 6
PAGE 7
Notes: 7
PAGE 8