Installation Instructions

ManualsBrandsToro ManualsRiding ProductsThree-Wheel Drive Kit, Greensmaster 3300/3400 Series TriFlex Traction Unit

FormNo.3440-457RevA

Three-WheelDriveKit

Greensmaster

3300/3400SeriesTriFlex

TractionUnit

ModelNo.04714

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Nopartsrequired

–

Removetheexistingwheel.

Wireformhoseguide

Bolt(1/2x1-1/2inches)

Installthewire-formhoseguide.

Bolt(1/2x2-1/2inches)

Locknut2

Wheelmotorassembly1

Hydraulicttings

Socket-headbolt(1/2x3-3/4inches)

Shimplate

Installthemotorassembly.

Tubeclamp2

Hydrauliclines2

Bolt(5/16x1-3/4inches)

Coverplate

Installthesteellines.

Hosebracket1

Bolt(5/16x7/8inch)

Flangenut(5/16inch)

Hoseshield1

Wireform

Installthehosebracket.

45°hydraulictting

Wiretie2

Flangenut1

Coverplate

Tubeclamp1

Bolt2

Nut1

R-clamp1

Installthetractionhoses.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3440-457*A

Summary of content (8 pages)

PAGE 1
Form No. 3440-457 Rev A Three-Wheel Drive Kit Greensmaster® 3300/3400 Series TriFlex® Traction Unit Model No. 04714 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 7 © 2020—The Toro® Company 8111 Lyndale Avenue South Bloomington, MN 55420 Description Qty. Use No parts required – Prepare the machine. No parts required – Remove the existing wheel.
PAGE 2
4. 1 Remove the 2 bolts and 2 nuts securing the vertical steering pivot to the castor fork (Figure 1). Discard these items. Important: Do not loosen the 2 remaining bolts securing the spindle to the castor fork. Preparing the Machine 3 No Parts Required Procedure 1. Park the machine on a level surface. 2. Lower the cutting units. 3. Engage the parking brake. 4. Shut off the engine and remove the key.
PAGE 3
4. 4 5 Installing the Motor Assembly Installing the Steel Lines Parts needed for this procedure: 2 Bolt (1/2 x 2-1/2 inches) 2 Locknut 1 Wheel motor assembly 2 Hydraulic fittings 2 Socket-head bolt (1/2 x 3-3/4 inches) 1 Shim plate Torque the bolts to 75 ft-lb (101.7 N∙m). Parts needed for this procedure: 2 Tube clamp 2 Hydraulic lines 1 Bolt (5/16 x 1-3/4 inches) 1 Cover plate Procedure Procedure 1. 1.
PAGE 4
6 Installing the Hose Bracket Parts needed for this procedure: 1 Hose bracket 2 Bolt (5/16 x 7/8 inch) 6 Flange nut (5/16 inch) 1 Hose shield 1 Wire form Gasoline-Powered Traction Units Install the hose bracket to the frame and secure it with 2 bolts (5/16 x 7/8 inch) and 2 flange nuts (5/16 inch) as shown in Figure 5. g015820 Figure 6 1. Bolt 2. Hose shield 4. Nut 5. Bolt (5/16 inch) 3. Wire form 2. Install the hose shield to the wire form and secure it with 2 bolts and 2 nuts.
PAGE 5
it to the lower steel line. Attach the opposite end to the lower hydraulic-pump fitting (Figure 8 or Figure 9). 4. Install the remaining hose through hose guide and attach to upper steel line. Attach the opposite end to the upper tee fitting for front-wheel motor (Figure 8 or Figure 9). 5. Install both hose assemblies into the tube clamp at the hose cover split and attach it to the bracket. (Figure 8; or Figure 9). 6. Tighten the jam nuts on the motor fittings. 7.
PAGE 6
g015824 Figure 9 Gasoline Engine 1. Wire tie 3. Cover plate 5. Bolt 7. Hydraulic pump attachment 2. Flange nut 4. Tube clamp 6. Front motor attachment 8. Secure the throttle cable to the frame with a wire tie at this location.
PAGE 7
Notes:
PAGE 8