Installation Instructions

ManualsBrandsToro ManualsRiding ProductsStandard Seat Kit, Greensmaster 3300/3400 Series TriFlex Traction Unit

FormNo.3433-172RevA

SeatKit

Greensmaster

3300/3400SeriesTriFlex

TractionUnit

ModelNo.04718

ModelNo.04719

InstallationInstructions

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Seatassembly

Flangenut4

Shortwireharness

Installthenewseat.

PreparingtheMachine

NoPartsRequired

Procedure

•Ifyouareinstallingthiskitonanewdieseltraction

unitwithoutaseat,removethe4carriagebolts

and4nutssecuringtheshippingbrackettothe

seatpanandarmrest(Figure1).Discardthe

shippingbracketandseatpanfasteners.Savethe

armrestfastenersandspacer.

Important:Ensurethatyousupportthe

armrestafterremovingitsothatitdoesnot

crimporhangbythecablesandwires.

g033261

Figure1

1.Armrest

4.Carriagebolt(save)

2.Spacer5.Carriagebolt(discard)

3.Shippingbracket(discard)6.Seatpan

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3433-172*A

Summary of content (8 pages)

PAGE 1
Form No. 3433-172 Rev A Seat Kit Greensmaster® 3300/3400 Series TriFlex® Traction Unit Model No. 04718 Model No. 04719 Installation Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Use Qty. 1 No parts required – Prepare the machine. 2 Seat assembly Flange nut Short wire harness 1 4 1 Install the new seat.
PAGE 2
• If you are installing a premium seat on a traction unit with a standard seat installed, complete the following procedure: 1. Park the machine on level ground, shut off the engine, engage the parking brake, and remove the ignition key. 2. Remove the 2 carriage bolts and nuts securing the armrest to the seat (Figure 2). Save the fasteners. Important: Ensure that you support the armrest after removing it so that it does not crimp or hang by the cables and wires. g015247 Figure 3 1. Seat rail 2.
PAGE 3
2 Installing the New Seat Parts needed for this procedure: 1 Seat assembly 4 Flange nut 1 Short wire harness Procedure 1. Install the 4 studs on the seat rails into the seat pan and secure them using 4 flange nuts (Figure 4). g195601 Note: There are 2 installation locations in the seat pan. For tall operators, install the seat into the rear holes. For shorter operators, install the seat into the front holes. g195602 Figure 4 1. Seat rail 2. Seat pan 3 3.
PAGE 4
2. Install the armrest to the seat using the 2 carriage bolts and flange nuts that you removed previously (Figure 5). Note: If you have a diesel machine, install the spacer removed in 1 Preparing the Machine (page 1). g015301 Figure 6 (Premium seat harness shown) 1. Open connector on the main wire harness 2. Short wire harness from the kit g195603 g195604 Figure 5 1. Armrest 3. Carriage bolt 2. Armrest bracket 3.
PAGE 5
Operation Seat Controls Seat-Adjusting Lever The seat-adjusting lever is located on the front, left corner of the seat (Figure 7). Twisting the handle up allows you to adjust the seat forward and rearward. g195599 Figure 8 g193737 Figure 7 1. Seat-adjusting handle Note: If you need additional adjustment on the seat, remove the 4 bolts securing the seat to the rails and move the seat to the second set of mounting holes provided (Figure 8). 5 1. Seat (standard seat shown) 3. Washer 2. Seat rails 4.
PAGE 6
Weight-Adjustment Lever Model 04719 Only You can adjust the seat for your weight to provide a smooth and comfortable ride. Important: To adjust the seat, the driver must be seated. Adjust the seat for your weight by pulling out the lever and then pumping it up to increase the suspension or down to decrease it (Figure 9). g015252 Figure 9 When the arrow is in the middle clear area of the viewing window, you have adjusted the seat correctly for your weight.
PAGE 7
Lumbar Support Knob Backrest Locking Lever Model 04719 Only Model 04719 Only The lumbar support increases both the seating comfort and a customized lumbar support for your lower back. You can adjust the back of the seat to provide a more comfortable ride. Turn the adjustment knob upward to adjust the curvature in the upper part of the backrest cushion. Turn the knob downward to adjust the curvature in the lower part of the backrest cushion (Figure 10).
PAGE 8