Form No. 3409-861 Rev A Dethatching Unit Greensmaster® 3300/3400 Series TriFlex® Traction Unit Model No. 04720—Serial No. 400000000 and Up Register at www.Toro.com.
WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Introduction This product complies with all relevant European directives. For details, please see the Declaration of Incorporation (DOI) at the back of this publication. g014403 Figure 1 1.
Contents Safety Safety ........................................................................... 3 Safety and Instructional Decals ................................. 4 Setup ............................................................................ 5 1 Installing the Front Roller ...................................... 5 2 Adjusting the Reel Blades for Positive Setting (Above Ground).................................................. 5 3 Adjusting the Reel Blades For Negative Setting (Below Ground) .....
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal104-7729 104-7729 1. Warning—read the instructions before servicing or performing maintenance. 2. Cutting/dismemberment hazard; hand or foot—shut off the engine and wait for moving parts to stop.
Setup 4. Rotate the height-of-cut until both ends of the front roller contact the level surface. 5. Verify contact by using a piece of paper to check each roller end. 1 6. Tighten both height-of-cut knob locknuts. Installing the Front Roller 3 No Parts Required Adjusting the Reel Blades For Negative Setting (Below Ground) Procedure The dethatching unit is shipped without a front roller.
4 Installing the Dethatching Reel No Parts Required Procedure See the traction unit Operator’s Manual for installing the reel to the machine. Important: If you set the dethatching reel at a negative setting, take care to prevent damaging the reel blades due to contact with concrete floors or paved surfaces. 5 Installing the Electrical Counterweight No Parts Required Procedure Note: If the dethatching unit is installed on greensmower Models 04530 or 04540, you must use an additional hybrid counterweight.
Product Overview Specifications Tractors These dethatching units will mount on the Greensmaster 3300 and 3400 Traction Units. Height-of-cut Dethatching depth is adjusted on the front roller by 2 vertical screws and held by 2 locking cap screws. Height-of-cut Range Bench HOC range is 4.78 mm (0.188 inch) below ground level to 6.35 mm (0.250 inch) above ground level. Reel Bearings Two sealed stainless steel, deep groove ball bearings. Rollers The rear roller is a 5.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Disassembling the Reel Disassemble the reel whenever you need to change a blade or replace the reel bearings. Important: Ensure that the 2 shaft retainers and spacer are in place before installing the bearing on the reel (Figure 6). Torque the insert nuts to 136 N∙m (100 ft-lb). g016597 Figure 6 1. Left-hand threaded insert nut 2. Bearing 4. Spacer 3. Seal 6. Shaft retainer (install these first) 5.
Notes:
Declaration of Incorporation The Toro Company, 8111 Lyndale Ave. South, Bloomington, MN, USA declares that the following unit(s) conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain Toro models as indicated on the relevant Declarations of Conformity. Model No. 04720 Serial No.
European Privacy Notice The Information Toro Collects Toro Warranty Company (Toro) respects your privacy. In order to process your warranty claim and contact you in the event of a product recall, we ask you to share certain personal information with us, either directly or through your local Toro company or dealer. The Toro warranty system is hosted on servers located within the United States where privacy law may not provide the same protection as applies in your country.
The Toro Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
