Form No. 3427-673 Rev A Dethatching Unit Greensmaster® 3300/3400 Series TriFlex® Traction Unit Model No. 04720—Serial No. 403430001 and Up Register at www.Toro.com.
This product complies with all relevant European directives. For details, please see the Declaration of Incorporation (DOI) at the back of this publication. Introduction The dethatching unit is mounted to a traction unit and is intended to be used by professional, hired operators in commercial applications. It is designed primarily for dethatching grass on well-maintained lawns in parks, golf courses, sports fields, and on commercial grounds.
Contents Safety Safety ....................................................................... 3 General Safety ................................................... 4 Cutting Unit Safety.............................................. 4 Blade Safety ....................................................... 4 Safety and Instructional Decals .......................... 4 Setup ........................................................................ 5 1 Installing the Front Roller .................................
General Safety Blade Safety This product is capable of amputating hands and feet. Always follow all safety instructions to avoid serious personal injury. A worn or damaged blade can break, and a piece of the blade could be thrown toward you or bystanders, resulting in serious personal injury or death. • Read and understand the contents of this • Inspect the blade periodically for wear or damage. Operator’s Manual before starting the machine. • Use care when checking the blades.
Setup 1 Installing the Front Roller 3. With the rear roller contacting the level surface, loosen both height-of-cut nuts. 4. Rotate the height-of-cut until both ends of the front roller contact the level surface. 5. Verify contact by using a piece of paper to check each roller end. 6. Tighten both height-of-cut knob locknuts. 3 No Parts Required Procedure Adjusting the Reel Blades For Negative Setting (Below Ground) The dethatching unit is shipped without a front roller.
. Tighten both height-of-cut knob locknuts. 4 Installing the Dethatching Unit No Parts Required Procedure g036342 See the traction unit Operator’s Manual for instructions to install the dethatching unit to the machine. Figure 5 1. Cap screw Important: If you set the dethatching unit at a 2. Electrical counterweight negative setting, prevent contact with concrete floors or paved surfaces. Contact with these surfaces can damage the dethatching-unit blades.
Specifications Product Overview Traction-Unit Compatibility The dethatching unit mounts on Greensmaster 3300 and 3400 series traction units. Height of Cut Dethatching depth is adjusted on the front roller by 2 vertical screws and held by 2 locking cap screws. Height-of-Cut Range Bench HOC range is 4.78 mm (0.188 inch) below ground level to 6.35 mm (0.250 inch) above ground level. Reel Bearings Two sealed stainless steel, deep groove ball bearings. Rollers The rear roller is a 5.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Disassembling the Reel Disassemble the reel whenever you need to change a blade or replace the reel bearings. Important: Ensure that the 2 shaft retainers and spacer are in place before installing the bearing on the reel (Figure 6). Torque the insert nuts to 136 N∙m (100 ft-lb). g016597 Figure 6 1. Left-hand threaded insert nut 2. Bearing 4. Spacer 3. Seal 6.
Notes:
Notes:
Declaration of Incorporation The Toro Company, 8111 Lyndale Ave. South, Bloomington, MN, USA declares that the following unit(s) conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain Toro models as indicated on the relevant Declarations of Conformity. Model No. 04720 Serial No.
The Toro Warranty Two-Year or 1,500 Hours Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for 2 years or 1,500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
