Operator's Manual

ManualsBrandsToro ManualsAttachmentsTri-Roller, Greensmaster 3300/3400 Series TriFlex Traction Unit

FormNo.3409-884RevB

Tri-Roller

forGreensmaster

3300/3400SeriesTriFlex

TractionUnits

ModelNo.04722—SerialNo.400000000andUp

Operator'sManual

Setup

InstallingtheTri-Roller

Units

NoPartsRequired

Procedure

1.Parkthemachineonalevelsurface,shutoffthe

engine,engagetheparkingbrake,andremove

thekey.

2.Positionthetri-rollerunitunderthesuspension

arm.

3.Withthelatchesonthesuspension-armbar

pointingup(Figure1),pushthesuspensionarm

downsothatthebartsoverthebaracrossthe

topofthetri-rollerunit(Figure2).

g018311

Figure1

1.Latch—closedposition3.Latch—openposition

2.Suspension-armbar

g018312

Figure2

1.Suspension-armbar

2.Tri-rollerunitbar

4.Closethelatchesdownandaroundthetri-roller

unitandlocktheminplace(Figure1).

Note:Youwillhearandfeela“click”whenthe

latchesareproperlylockedinplace.

5.Insertthemotorintotheleftsideofthetri-roller

unit(asviewedfromtheoperator’sposition)and

pullthemotorretainingbaronthetri-rollerunit

towardthemotoruntilyouheara“click”from

bothsidesofthemotor(Figure3).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3409-884*B

Summary of content (8 pages)

PAGE 1
Form No. 3409-884 Rev B Tri-Roller for Greensmaster® 3300/3400 Series TriFlex® Traction Units Model No. 04722—Serial No. 400000000 and Up Operator's Manual Setup 1 Installing the Tri-Roller Units No Parts Required Procedure 1. g018312 Park the machine on a level surface, shut off the engine, engage the parking brake, and remove the key. 2. Position the tri-roller unit under the suspension arm. 3.
PAGE 2
Removing the Tri-Roller Unit No Parts Required Procedure 1. Park the machine on a clean level surface, lower the tri-roller units to the ground until the suspension hydraulics are fully extended, shut off the engine, engage the parking brake, and remove the key from the ignition switch. 2. Push the motor retaining bar out of the slots on the motor toward the tri-roller unit and remove the motor from the tri-roller unit. g014690 Figure 3 1. Motor 3. Cavity 2. Spline shaft 4.
PAGE 3
7. Repeat steps 2 through 6 for the other tri-roller units as required. 3 Adding Rear Weight Parts needed for this procedure: 1 Weight kit, 119-7129 (purchase separately) Procedure g254873 This machine complies with the ANSI B71.4-2012 and EN ISO 5395:2013 Standards when equipped with the Weight Kit, Part No. 119-7129. Figure 5 1. Cap screws Operation 2.
PAGE 4
Maintenance Lubricating the Tri-Roller Lubricate the 2 grease fittings (Figure 6) on each tri-roller unit after every 15 hours of operation, with No. 2 lithium grease. Use a hand-operated grease gun for best results. 1. Wipe each grease fitting with a clean rag. 2. Apply grease to the tri-roller shaft bearings until you feel pressure (Figure 6). g018317 Figure 6 3. Wipe excess grease away.
PAGE 5
Notes:
PAGE 6
Declaration of Incorporation The Toro Company, 8111 Lyndale Ave. South, Bloomington, MN, USA declares that the following unit(s) conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain Toro models as indicated on the relevant Declarations of Conformity. Model No. 04722 Serial No.
PAGE 7
European Privacy Notice The Information Toro Collects Toro Warranty Company (Toro) respects your privacy. In order to process your warranty claim and contact you in the event of a product recall, we ask you to share certain personal information with us, either directly or through your local Toro company or dealer. The Toro warranty system is hosted on servers located within the United States where privacy law may not provide the same protection as applies in your country.
PAGE 8
The Toro Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).