Installation Instructions

ManualsBrandsToro ManualsRiding ProductsPremium Seat Kit, Greensmaster 3360 eTriFlex Traction Unit

FormNo.3431-480RevA

SeatKit

Greensmaster

3000SeriesTriFlex

oreTriFlexTractionUnit

ModelNo.04508

ModelNo.04729

InstallationInstructions

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Seatassembly

Flangenut4

Shortwireharness

Cabletie

Installthenewseat.

PreparingtheMachine

NoPartsRequired

Procedure

•IfyouareinstallingseatModelNo.04508onto

modelyear2018oroldertractionunits,youmust

rstinstallkitModelNo.139-6479.

•Ifyouareinstallingthiskitonanew,dieselor

eTriextractionunitwithoutaseat,removethe2

carriagebolts,2angebolts,and4nutssecuring

theshippingbrackettotheseatpanandarmrest

(Figure1).Discardtheshippingbracketandseat

panfasteners.Savethearmrestfasteners.

Important:Ensurethatyousupportthe

armrestafterremovingitsothatitdoesnot

crimporhangbythecablesandwires.

g277118

Figure1

1.Armrest

4.Seatpan

2.Shippingbracket(discard)5.Carriagebolt(discard)

3.Flangebolt(save)

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3431-480*A

Summary of content (8 pages)

PAGE 1
Form No. 3431-480 Rev A Seat Kit Greensmaster® 3000 Series TriFlex® or eTriFlex Traction Unit Model No. 04508 Model No. 04729 Installation Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Use Qty. 1 No parts required – Prepare the machine. 2 Seat assembly Flange nut Short wire harness Cable tie 1 4 1 2 Install the new seat. 1 Preparing the Machine No Parts Required Procedure • If you are installing seat Model No.
PAGE 2
• If you are installing a premium seat on a traction 2 unit with a standard seat installed, complete the following procedure: 1. 2. Park the machine on level ground, shut off the engine (if equipped), engage the parking brake, and remove the ignition key. Installing the New Seat Remove the 2 flange bolts and nuts securing the armrest to the seat (Figure 2). Save the fasteners.
PAGE 3
Note: The eTriflex does not have holes in the 3. seat pan; if you want to adjust the seat, change the position of the seat on the seat mount brackets as shown in Figure 5. Route the console wire harness between the seat bracket and the seat slide (Figure 6). g278221 Figure 6 g285734 Figure 5 1. Forward hole in the seat mount bracket 2. Seat mount washer 1. Seat bracket 2. Seat 3. Seat mount bolt 4.
PAGE 4
6. Operation Install the armrest to the seat using the 2 flange bolts and flange nuts that you removed previously (Figure 8). Seat Controls Seat-Adjusting Lever The seat-adjusting lever is located on the front, left corner of the seat (Figure 9). Twisting the handle up allows you to adjust the seat forward and rearward. g277239 g193737 Figure 9 1.
PAGE 5
Weight-Adjustment Lever Models 04729 You can adjust the seat for your weight to provide a smooth and comfortable ride. Important: To adjust the seat, the driver must be seated. Adjust the seat for your weight by pulling out the lever and then pumping it up to increase the suspension or down to decrease it (Figure 10). When the arrow is in the middle clear area of the viewing window, you have adjusted the seat correctly for your weight.
PAGE 6
Lumbar Support Knob Backrest Locking Lever Models 04729 Models 04729 The lumbar support increases both the seating comfort and a customized lumbar support for your lower back. You can adjust the back of the seat to provide a more comfortable ride. Turn the adjustment knob upward to adjust the curvature in the upper part of the backrest cushion. Turn the knob downward to adjust the curvature in the lower part of the backrest cushion (Figure 11).
PAGE 7
Notes:
PAGE 8