Form No. 3449-912 Rev A Greensmaster® 1018, 1021, or 1026 Mower Model No. 04820—Serial No. 410200000 and Up Model No. 04830—Serial No. 410200000 and Up Model No. 04840—Serial No. 410300000 and Up Register at www.Toro.com.
This product complies with all relevant European directives; for details, please see the separate product specific Declaration of Conformity (DOC) sheet. Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 identifies the location of the model and serial numbers on the product. Write the numbers in the space provided.
Servicing the Engine Oil.................................... 24 Servicing the Air Cleaner .................................. 25 Servicing the Spark Plug................................... 26 Controls System Maintenance ............................. 27 Adjusting the Traction Cable ............................. 27 Adjusting the Service/Parking Brake................. 28 Adjusting the Reel-Control Cable...................... 29 Adjusting the Throttle Cable..............................
Safety • Do not operate the machine without all guards This machine has been designed in accordance with EN ISO 5395 and ANSI B71.4-2017. • Keep bystanders and children out of the operating and other safety protective devices in place and functioning properly on the machine. area. Never allow children to operate the machine. • Shut off the engine, remove the key (if equipped), General Safety and wait for all movement to stop before you leave the operator’s position.
decal138-2138 138-2138 decal138-1589 138-1589 1. Engage the reels. 1. Poisonous fumes or toxic gases, asphyxiation hazard—do not run the engine in an enclosed space. 4. Warning— disconnect the spark plug wire before performing maintenance. 2. Explosion hazard—shut off the engine before adding fuel; no fire, open flames, or smoking when adding fuel. 5. Hot surface hazard—do not touch the hot surface. 3. Warning—shut off the engine and close the fuel shutoff valve before leaving the machine. 6.
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Use Qty. 1 Cutting unit (order separately; contact your authorized Toro distributor) Coupler Spring (Model 04830 and 04840 only) Socket-head screw 1 1 4 2 Left wheel shaft 1 Install the transport-wheel shaft (Model 04840 only). 3 4 5 Transport Wheel Kit (order separately; contact your authorized Toro distributor) 1 Install the transport wheels (optional).
3. Adjusting and Installing the Cutting Unit Use 4 socket-head screws to install the cutting unit to the machine (Figure 4). Models 04830 and 04840 1. Use 4 socket-head screws to install the cutting unit to the machine (Figure 6). g333153 Figure 4 1. Socket-head screw g333212 4. Figure 6 Determine your appropriate height-of-cut setting and adjust the traction drum to this setting; refer to Adjusting the Traction-Drum Position (page 15). 5.
transmission alignment; refer to Adjusting the Reel-Driveshaft Position (page 33). 3 2 Installing the Transport Wheels Installing the Transport-Wheel Shaft Optional Parts needed for this procedure: Model 04840 Only 1 Parts needed for this procedure: 1 Left wheel shaft Transport Wheel Kit (order separately; contact your authorized Toro distributor) Procedure To install the transport wheels, you must first acquire the Transport Wheel Kit (Model 04123).
4 5 Installing the Grass Basket Adjusting the Engine Speed Parts needed for this procedure: For CE-Compliant Countries Only 1 Grass basket Parts needed for this procedure: 1 Procedure Grasp the basket by the top lip and slide it onto the basket mounting rods (Figure 9).
Controls Product Overview g274957 Figure 11 1. Grass basket 2. Kickstand 4. Fuel tank 5. Transport-wheel axle 3. Handle 6. Cutting unit g271082 Figure 12 10 1. Clutch bail 2. Cutting-unit-drive lever 5. Throttle control 6. Hour meter 3. Parking-brake latch 7. Lift-assist handle 4. Service-brake lever 8.
Clutch Bail Lift-Assist Handle Use the clutch bail (Figure 12) to engage or disengage the traction drive. Use the lift-assist handle (Figure 12) to help with adjusting the handle height or raise and lower the kickstand. • Engage the traction drive: Pull up and hold the bar to the handle. • Disengage the traction drive: Release the bar. Handle-Height Adjuster Throttle Control Use the handle-height adjuster (Figure 13) to move the handle height to a comfortable operating position.
Fuel-Shutoff Valve The fuel-shutoff valve is located on the side of the engine below the choke control (Figure 14). Note: Close the fuel-shutoff valve when the machine is not used for a few days, during transport to and from the job site, or when the machine is parked inside a building; refer to Opening and Closing the Fuel-Shutoff Valve (page 17). Recoil-Starter Handle Pull the recoil-starter handle (Figure 14) to start the engine.
Specifications Operation Model 04820 Model 04830 Model 04840 Width 84 cm (33 inches) 91 cm (36 inches) 104 cm (41 inches) Dry weight* 95 kg (210 lb) 100 kg (220 lb) 107 kg (235 lb) Width of cut 46 cm (18 inches) 53 cm (21 inches) 66 cm (26 inches) Height of cut Dependent on traction-drum position [refer to Adjusting the Traction-Drum Position (page 15)] and use of High Height-of-Cut Kit.
Filling the Fuel Tank • Remove equipment from the truck or trailer and refuel it on the ground. If this is not possible, refuel such equipment with a portable container rather than from a fuel-dispenser nozzle. 1. • Keep the nozzle in contact with the rim of the fuel tank or container operating at all times until fueling is complete. Clean around the fuel-tank cap and remove the cap from the tank (Figure 17).
Adjusting the Clip Rate The clip rate is determined by the following machine settings: • Reel speed: You can adjust the reel speed to a high or low setting; refer to Adjusting the Reel Speed (page 15). • Reel-drive-pulley position: You can set the reel-drive pulleys in 2 positions; refer to your cutting unit Operator’s Manual.
2. Ensure that the traction and reel-drive controls are in the NEUTRAL position. 3. Start the engine; refer to Starting the Engine (page 18). 4. Set the throttle control to SLOW, tip the front of the machine up, gradually engage the traction drive, and slowly increase the engine speed. 5. Adjust the throttle to operate the mower at the desired ground speed and transport the machine to the desired destination.
Opening and Closing the Fuel-Shutoff Valve Control fuel flow to the engine with the fuel-shutoff valve as follows: • To open the fuel valve, turn the fuel-shutoff lever toward the recoil starter handle (Figure 22). • To shut the fuel valve, turn the fuel-shutoff lever away from the recoil starter handle (Figure 22). g274946 Figure 20 1. Axle 4. 2.
Slope Safety • Keep bystanders and children out of the operating • • • • • • • • • • • • • • • area. If co-workers must be present, use caution and ensure that the grass basket is installed on the machine. Operate the machine only in good visibility to avoid holes or hidden hazards. Do not operate the machine when there is the risk of lightning. Use care when mowing on wet grass. Poor footing could cause a slip-and-fall accident. Keep your hands and feet away from the cutting unit.
2. Operating Tips Ensure that the fuel-shutoff valve is open; refer to Opening and Closing the Fuel-Shutoff Valve (page 17) 3. Move the On/Off switch to the ON position. 4. Use the throttle control to increase the engine speed. 5. Move the choke lever halfway between the CHOKE and RUN positions when starting a cold engine; refer to Using the Choke Lever (page 17) Important: Grass clippings act as a lubricant when mowing.
Shutting Off the Engine 1. Release the clutch bail. 2. Move the throttle control to the SLOW position. 3. Move the On/Off switch to the OFF position. 4. Close the fuel-shutoff valve before you store or transport the machine After Operation After Operation Safety General Safety • Shut off the machine, remove the key (if equipped), and wait for all movement to stop before you leave the operator’s position. Allow the machine to cool before adjusting, servicing, cleaning, or storing it.
Engaging or Disengaging the Transmission Installing the Transport Wheels 1. Move the kickstand to the TRANSPORT-WHEEL-SERVICE position; refer to Kickstand (page 12) 2. Slide a wheel onto an axle (Figure 25). You can disengage the drum from the transmission to allow the machine to be maneuvered. Disengage the transmission when you need to move the machine without starting the engine (e.g., performing maintenance in an enclosed area).
Maintenance WARNING Failure to properly maintain the machine could result in premature failure of machine systems, causing possible harm to you or bystanders. Keep the machine well maintained and in good working order as indicated in these instructions. Note: Determine the left and right sides of the machine from the normal operating position. Important: Do not tip the machine at an angle greater than 25°.
Daily Maintenance Checklist Important: Duplicate this page for routine use. Maintenance Check Item For the week of: Mon. Tues. Wed. Thurs. Fri. Check the brake-lock-lever operation. Check the fuel level. Check the engine-oil level. Check the air filter. Clean the engine cooling fins. Check for unusual engine noises. Check for unusual operating noises. Check the reel-to-bedknife adjustment. Check the height-of-cut adjustment. Touch up damaged paint. Clean the machine.
Pre-Maintenance Procedures Engine Maintenance Preparing the Machine for Maintenance • Do not change the governor speed or overspeed Engine Safety the engine. • Run the engine dry or remove the fuel with a hand pump; never siphon the fuel. If you must drain the fuel tank, do it outdoors. WARNING While you are maintaining or adjusting the machine, someone could start the engine. Accidentally starting the engine could seriously injure you or other bystanders.
Changing the Engine Oil Service Interval: After the first 20 hours/After the first month (whichever comes first) Every 100 hours/Every 6 months (whichever comes first) WARNING Oil may be hot after the engine has been run, and contact with hot oil can cause severe personal injury. Avoid contacting the hot engine oil when you drain it. g266053 Figure 29 1. Dipstick 1. Shut off the engine and wait for all moving parts to stop; refer to Shutting Off the Engine (page 20). 2.
Note: Ensure that dirt and debris do not enter the air duct leading to the carburetor. Note: Ensure that no dirt or debris from the air-cleaner cover fall into the base. 4. Remove the foam and paper elements from the base. 5. Remove the foam element from the paper element. 6. 11. Install the air-cleaner elements and ensure that they are properly positioned. Install the lower wing nut. 12. Install the cover and install the upper wing nut to secure it.
Controls System Maintenance Adjusting the Traction Cable Adjust the traction cable to achieve a gap of 1.1 mm (0.045 inch) between the friction disc and the pressure plate. 1. Access the friction disc and pressure plate by removing the clutch cover (Figure 33). g274532 Figure 34 1. Traction cable 2. Jam nut g274480 Figure 33 1. Clutch cover 2. 2. Bolt Loosen the jam nuts and adjust the traction cable (Figure 34) so that a 1.1 mm (0.
Adjusting the Service/Parking Brake Adjust the service/parking brake if it slips during operation. 1. Disengage the parking brake. 2. Measure the free play at the end of the parking-brake handle (Figure 36). The handle free play should be between 12.7 to 25.4 mm (0.50 to 1 inch). If the free play is not within this amount, proceed to step 3 to adjust the brake cable. g345043 Figure 37 1. Front-cable jam nut 2. Rear jam nut g373542 Figure 36 1. Parking-brake handle 3. 2. Appropriate free play of 12.
Adjusting the Reel-Control Cable Note: Ensure that the engine is at a normal operating temperature before you adjust the throttle cable. To remove slack from the reel-control cable, perform the following steps: 1. 2. Move the reel-speed-control knob to the high-reel-speed position; refer to Adjusting the Reel Speed (page 15). 2. Start the engine and use the throttle control to decrease the engine speed to low idle. 3. Observe the low-idle engine speed on your tachometer.
The ideal range for high idle (for use in non-CE-compliant countries) is 3,350 to 3,550 rpm. If the tachometer shows a speed below 3,350 or above 3,550 rpm, perform steps 4 through 7 until a speed between 3,350 to 3,550 rpm is attained. If you use the machine in a country that complies to CE standards, adjust the high idle speed to the following specifications: • 1018 machines: 3,000 rpm • 1021 and 1026 machines: 3,150 rpm 4. Shut off the engine. 5.
Cutting Unit Maintenance Blade Safety • Use care when checking the reel cutting-unit. Wear gloves and use caution when servicing the reel. A worn or damaged blade or bedknife can break, and a piece could be thrown toward you or bystanders, resulting in serious personal injury or death. Inspect the blades and bedknives periodically for excessive wear or damage. Use care when checking the blades. Wear gloves and use caution when servicing them.
g333153 Figure 44 1. Socket-head screw 6. Use the previously removed socket-head screws, washers, and spacers to secure the reel-drive assembly to the cutting-unit side plate (Figure 45). Ensure that the reel-drive-assembly driveshaft is installed to the transmission-driveshaft coupler (Figure 45). g333188 Figure 46 1. Socket-head screw 4. 2. Cutting-unit-drive coupler Slide the cutting-unit-drive coupler onto the transmission driveshaft (Figure 46).
Adjusting the Reel-Driveshaft Position Removing the Cutting Unit You can adjust the reel driveshaft position by adjusting the reel-drive-assembly position: Removing the Cutting Unit (Model 04820) 1. Loosen the bolt shown in Figure 47. 1. Move the kickstand to the CUTTING-UNIT-SERVICE position; refer to Kickstand (page 12). 2. Remove the grass basket (if equipped). 3. Remove the reel-drive assembly from the cutting unit (Figure 48) and retain the hardware. g304660 Figure 47 1.
Removing the Cutting Unit (Model 04830 and 04840) 1. Move the kickstand to the CUTTING-UNIT-SERVICE position; refer to Kickstand (page 12). 2. Remove the grass basket (if equipped). 3. Release the cutting-unit-drive coupler from the transmission driveshaft (Figure 50).
Storage Storage Safety • Shut off the engine, remove the key (if equipped), and wait for all movement to stop before you leave the operator’s position. Allow the machine to cool before adjusting, servicing, cleaning, or storing it. • Do not store the machine or fuel container where there is an open flame, spark, or pilot light, such as on a water heater or other appliance. Storing the Machine 1.
Notes:
Notes:
EEA/UK Privacy Notice Toro’s Use of Your Personal Information The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer.
The Toro Warranty Two-Year or 1,500 Hours Limited Warranty Parts Conditions and Products Covered The Toro Company warrants your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for 2 years or 1,500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.
