Form No. 3406-814 Rev C Electric Lift Kit Workman® GTX Utility Vehicle Model No. 07143—Serial No. 316000001 and Up Model No. 07144—Serial No. 316000001 and Up Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Note: Reuse any mounting hardware that you removed and is not replaced with hardware from the kit. Preparing the Machine 1.
Placing the Bed into the Service Position Note: If the draw bar is installed on the machine, you must remove it before placing the bed into the service position. Insert the prop rod into the service position.
Installing the Lift Bracket 1x 5x 5x 1. Remove the existing bolt and nut from the rear-frame tube. Note: Discard the bolt and nut. 2. Remove the 2 existing plastic rivets from the rear-frame tube. Note: Retain the 2 plastic rivets. 3. Install the lift bracket to the rear-frame tube using the 5 flange-head bolts (3/8 x 2-1/2 inches) and 5 flange nuts (3/8 inch). 4. Install the 2 previously removed plastic rivets into the rear-frame tube.
Installing the Lift Latch 1x 1. Remove the 2 existing bolts from the cargo-bed lever. 2. Install the lift latch to the cargo-bed lever using the 2 previously removed bolts, and torque the bolts to 15 to 16 N∙m (11 to 12 ft-lb).
Installing the Lift Plate 1x 6x 1. Remove the 6 existing bolts and bed braces from the cargo bed. Note: Discard the bolts and bed braces. 2. Install the lift plate to the cargo bed using the 6 bolts, and torque the bolts to 15 to 16 N∙m (11 to 12 ft-lb).
Installing the Actuator Stop Electric Machine Only 1x 1x 1x Install the actuator stop to the battery tray mounting bracket using the bolt and nut.
Installing the Fuse 1x Install the 15A fuse into the fuse block.
Installing the Switch 1x 1. Remove the plastic cover from the dashboard. Note: Discard the plastic cover. 2. Install the switch connector through the opening in the dashboard. 3. Install the switch to the switch connector. 4. Ensure that the switch is oriented properly.
Installing the Lift Cylinder 1x 2x 2x 1x Important: Use the cable tie to secure the lift-cylinder wire to the wire harness, away from sharp or moving parts. Ensure that you allow enough slack in the wire harness for its full range of motion. 1. Install the lift cylinder using a clevis pin and hairpin cotter. 2. Connect the wire harness and secure it to the machine rail using the cable tie. 3. Rotate the lift cylinder upward to a 45° angle, then use a block to support the lift cylinder. 4.
Important: Use a block to support the lift cylinder so that it extends upward at a 45° angle.
Removing the Prop-Rod Assembly Remove the 2 bolts (3/8 x 2-1/2 inches), 2 flange nuts (3/8 inch), and 3 bolts (5/16 x 3/4 inch) from the prop-rod assembly, and remove the prop-rod assembly.
Operation WARNING Driving the machine with the cargo box raised may cause the machine to tip or roll easier. The box structure may become damaged if you operate the machine with the box raised. • Operate the machine only when the cargo box is down. • After dumping the contents in the cargo box, lower the box. CAUTION The weight of the box may be heavy. Hands or other body parts could be crushed. Keep hands and other body parts clear when lowering the box.
Raising and Lowering the Bed Important: Unlock the bed latch when using the electric lift to raise and lower the bed. Press upward on the switch to raise the bed. Press downward on the switch to lower the bed.
Notes:
Declaration of Incorporation Model No. Serial No.
The Toro Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
