Installation Instructions

ManualsBrandsToro ManualsVehiclesFront Hitch Kit, Workman GTX or MDX Series Utility Vehicles without Brush Guard

FormNo.3402-368RevA

FrontHitchKit

Workman

GTXorMDXSeriesUtilityVehicleswithoutBrush

Guard

ModelNo.07147

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Quickattachment

Longbrush-guardmountbracket(GTXand

GTXelectricmodelsonly)

Shortbrush-guardmountbracket(MDXand

MDX-Dmodelsonly)

Hex-head-angebolt(5/16x1inch)

Flangenut(5/16inch)

Carriagebolt(5/16x7/8inch)

Hex-socket,button-headbolt1

Jamnut1

T-handle1

Lowerbrush-guardbracket(MDXandMDX-D

modelsonly)

Hex-head-angebolt—3/8x1inch(MDXand

MDX-Dmodelsonly)

Flangenut—3/8inch(MDXandMDX-D

modelsonly)

Installthekit.

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

ForMDXandMDX-DModels

1.Stopthemachineonalevelsurface,settheparking

brake,shutofftheengine,andremovethekey.

2.Installthelowerbrush-guardmountbrackettothe

tractionunitframewith4hex-headangebolts(3/8x

1inch)and4angenuts(3/8inch)asshowninFigure

1.Torquethefastenersto37to45N∙m(27to33ft-lb).

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3402-368*A

Summary of content (4 pages)

PAGE 1
Form No. 3402-368 Rev A Front Hitch Kit Workman® GTX or MDX Series Utility Vehicles without Brush Guard Model No. 07147 Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Installation Loose Parts Use the chart below to verify that all parts have been shipped. Description Qty.
PAGE 2
Figure 1 9. Lower brush-guard bracket 1. Quick attachment 5. Carriage bolt (5/16 x 7/8 inch) 2. Bumper 6. Hex-socket, button-head bolt 3. Hex-head-flange bolt (5/16 x 1 inch) 7. Jam nut 11. Hex-head-flange bolt (3/8 x 1 inch) 4. Flange nut (5/16 inch) 8. T-handle 12. Flange nut (3/8 inch) 3. Loosely install the short brush-guard mount bracket to the traction unit frame (through the bumper) with 2 flange nuts (5/16 inch) as shown in Figure 1. 4.
PAGE 3
For GTX and GTX Electric Models 2. Loosely install the long brush-guard mount bracket to the traction unit frame (through the bumper) with 2 nuts (5/16 inch) as shown in Figure 2. 1. Stop the machine on a level surface, set the parking brake, shut off the engine, and remove the key. Figure 2 1. Quick attachment 4. Flange nut (5/16 inch) 7. Jam nut 2. Long brush-guard mount bracket 5. Carriage bolt (5/16 x 7/8 inch) 8. T-handle 3. Hex-head-flange bolt (5/16 x 1 inch) 6.
PAGE 4