Operator's Manual

ManualsBrandsToro ManualsVehicles48V Electric Lift Kit, Workman GTX Electric Utility Vehicle with Extended Bed

FormNo.3406-372RevB

ElectricLiftKit

Workman

GTXUtilityVehiclewithExtendedBed

ModelNo.07167—SerialNo.316000001andUp

ModelNo.07168—SerialNo.316000001andUp

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Important:YoumustinstallthiskitinconjunctionwiththeExtendedBedKit(ToroModelNo.07149).

Important:WhenyouhavetheElectricLiftKitinstalledontheextendedbed,donotexceed181kg(400lb)when

liftingacenteredload;otherwisedamagemayoccur.

Ifyoucentertheloadtowardthefrontofthecargobed,theliftcapacitydecreases.

Important:WheninstallingtheElectricLiftKit,useanoverheadhoisttoraisetheextendedcargobed(Figure1).

Figure1

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3406-372*B

Summary of content (12 pages)

PAGE 1
Form No. 3406-372 Rev B Electric Lift Kit Workman® GTX Utility Vehicle with Extended Bed Model No. 07167—Serial No. 316000001 and Up Model No. 07168—Serial No. 316000001 and Up Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Important: You must install this kit in conjunction with the Extended Bed Kit (Toro Model No. 07149).
PAGE 2
Preparing the Machine 1. Park the machine on a level surface. 2. Engage the parking brake. 3. Shut off the engine and remove the key from the key switch.
PAGE 3
Installing the Lift Bracket 1x 5x 5x Important: The extended cargo bed is removed from the figure for clarity; do not remove the extended cargo bed. 1. Remove the existing bolt and nut from the rear-frame tube. Note: Discard the bolt and nut. 2. Remove the 2 existing plastic rivets from the rear-frame tube. Note: Retain the 2 plastic rivets. 3. Install the lift bracket to the rear-frame tube using the 5 flange-head bolts (3/8 x 2-1/2 inches) and 5 flange nuts (3/8 inch). 4.
PAGE 4
Installing the Actuator Stop Electric Machine Only 1x 1x Install the actuator stop to the battery tray mounting bracket using the bolt and nut.
PAGE 5
Installing the Fuse 1x Install the 15A fuse into the fuse block.
PAGE 6
Installing the Switch 1x 1. Remove the plastic cover from the dashboard. Note: Discard the plastic cover. 2. Install the switch connector through the opening in the dashboard. 3. Install the switch to the switch connector. 4. Ensure that the switch is oriented properly.
PAGE 7
Installing the Lift Cylinder 1x 2x 2x 1x Important: Use the cable tie to secure the lift-cylinder wire to the wire harness, away from sharp or moving parts. Ensure that you allow enough slack in the wire harness for its full range of motion. 1. Install the lift cylinder using a clevis pin and hairpin cotter. 2. Connect the wire harness and secure it to the machine rail using the cable tie. 3. Rotate the lift cylinder upward to a 45° angle, then use a block to support the lift cylinder. 4.
PAGE 8
Important: Use a block to support the lift cylinder so that it extends upward at a 45° angle.
PAGE 9
Operation WARNING Driving the machine with the cargo box raised may cause the machine to tip or roll easier. The box structure may become damaged if you operate the machine with the box raised. • Operate the machine only when the cargo box is down. • After dumping the contents in the cargo box, lower the box. CAUTION The weight of the box may be heavy. Hands or other body parts could be crushed. Keep hands and other body parts clear when lowering the box.
PAGE 10
Notes:
PAGE 11
Declaration of Incorporation Model No. Serial No.
PAGE 12
The Toro Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).