Form No. 3416-346 Rev A Canopy with ROPS Kit Workman® GTX Utility Vehicle Model No. 07169—Serial No. 400000000 and Up Installation Instructions Safety WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Rollover Protection System (ROPS) Safety • Keep the ROPS in safe operating condition by • Do not remove the ROPS from the machine. • Replace a damaged ROPS.
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 7 8 9 Description Use Qty. No parts required – Prepare the machine. No parts required – Remove the seat assembly. No parts required – Remove the handholds. No parts required – Remove the side panels. No parts required – Remove the rubber covers. No parts required – Drill the holes for the ROPS brackets. No parts required – Cut the rubber covers.
Procedure 16 17 Description Qty.
1 Preparing the Machine No Parts Required Procedure 1. Park the machine on a level surface. 2. Engage the parking brake. 3. Shut off the engine and remove the key. g038447 Figure 1 2 Removing the Seat Assembly No Parts Required Procedure 1. 2. Push the seat assembly forward to the raised position. g190187 Figure 2 Slide the seat assembly to the side out of the pins, and lift the seat assembly upward (Figure 2). 1.
3 Removing the Handholds No Parts Required Procedure Remove the 3 flange bolts (5/16 x 3/4 inch) and 3 flange nuts (5/16 inch) from the right and left handhold, and remove them (Figure 3 and Figure 4). g036761 Figure 4 Right Handhold Shown 1. Right handhold 2. Flange bolt (5/16 x 3/4 inch) g036760 Figure 3 Left Handhold Shown 1. Left handhold 3. Flange nut (5/16 inch) 2. Flange bolt (5/16 x 3/4 inch) 5 3.
4 Removing the Side Panels No Parts Required For Electric Machines 1. Remove the charger and the charger cable from the charger bracket (Figure 5). g193101 Figure 6 Left Side Shown (Top View) 1. Left side panel 3. Torx-head screw (M6.0 x 22 mm) 2. Charger bracket 3. g218768 Figure 5 Left Side Shown 1. Charger 3. Charger cable 2. Charger bracket 2. Use a T30 socket wrench to remove the 4 torx-head screws (M6.0 x 22 mm) securing the charger bracket to the left side panel (Figure 6).
For Gasoline Machines 1. Disconnect the vent tube and fuel line from the fuel tank (Figure 8). DANGER In certain conditions, fuel is extremely flammable and highly explosive. A fire or explosion from fuel can burn you and others and can damage property. • Drain fuel from the fuel tank when the engine is cold. Do this outdoors and in an open area. Wipe up any fuel that spills. • Never smoke when handling fuel, and stay away from an open flame or where fuel fumes may be ignited by a spark. g193100 2.
4. and use a T30 socket wrench to remove the 4 torx-head screws (M6.0 x 22 mm) that secure the right side panel, and remove the right side panel (Figure 11). Use a T30 socket wrench to remove the 6 torx-head screws (M6.0 x 22 mm) from the left side panel and remove the side panel (Figure 9). Note: The battery comes off with the right side panel as shown in Figure 11. g199036 Figure 9 Left Side Shown (Top View) 1. Side panel 5. g033999 Figure 11 Right Side Shown (Top View) 2. Torx-head screw (M6.
5 Removing the Rubber Covers No Parts Required Procedure g205374 Figure 13 Left Side Shown Remove the 10 plastic rivets and the cable tie from each rubber cover and remove the rubber covers (Figure 12). 1. Hole toward the front of the frame rail 2. 3. 4. Using a clamp, secure the ROPS bracket in place. Mark the hole locations on the ROPS bracket (Figure 13). Using a ROPS bracket as a guide, drill 3 holes (13.5 mm or 17/32 inch) into the frame (Figure 14).
7 Cutting the Rubber Covers No Parts Required Procedure Cut the rubber covers using the measurements shown in Figure 15. Note: The cuts in the rubber cover allow for space to install the ROPS brackets. g217562 Figure 15 1.
8 Installing the Rubber Covers Parts needed for this procedure: 2 Cable tie 4 Plastic rivets Procedure Install each rubber cover using the previously removed 10 plastic rivets and a cable tie (Figure 16). If the previously removed rivets are damaged or missing, replace them with the rivets provided in this kit. g217602 Figure 16 Left Side Shown 1. Plastic rivet (10) 3. Cable tie 2.
9 Trimming the Side Panels No Parts Required Procedure Trim the side panels using the measurements shown in Figure 17. g217567 Figure 17 1. Trim to this line 2.
10 11 Installing the ROPS Brackets Installing the Roll Bar Parts needed for this procedure: Parts needed for this procedure: 1 Roll bar 4 Flange-head bolt (1/2 x 3-1/2 inches) 4 Locknut (1/2 inch) 1 Left ROPS bracket 1 Right ROPS bracket 6 Flange-head bolt (1/2 x 3 inches) 10 Flat washer (1/2 inch) Procedure 6 Locknut (1/2 inch) Note: Have an assistant help you to raise the roll bar into position. 1. Procedure 1.
12 13 Installing the Side Panels Installing the Handholds No Parts Required No Parts Required For Electric Machines Procedure 1. Install the left side panel using the previously removed 4 torx-head screws (M6.0 x 22 mm) as shown in Figure 7. 2. Secure the charge bracket to the left side panel using the previously removed 4 torx-head screws (M6.0 x 22 mm) as shown in Figure 6. 3. Secure the charger and the charger cable to the charger bracket (Figure 5). 4. Repeat step 1 on the right side. 5.
3. Repeat steps 1 and 2 to install the other seat latch. 4. Install a seat belt using a hex-head bolt (7/16 x 1 inch), 2 flat washers (7/16 inch), and a locknut (7/16 inch) as shown in Figure 21. 15 Installing the Seat Assembly No Parts Required Procedure Slide the seat assembly onto the pins and lower the seat assembly (Figure 22). g204766 Figure 21 1. Locknut (7/16 inch) 3. Seat belt 2. Flat washer (7/16 inch) 4. Hex-head bolt (7/16 x 1 inch) 5.
Procedure 16 Note: Do not tighten any fasteners except when instructed. 1. Installing the ROPS Extension Using the dimensions shown in Figure 23, drill 2 holes (5/16 inch) into the outside of the floor plate on the left and right sides of the machine.
g214689 Figure 25 g217564 1. Windshield support 3. Nut—inside dash frame (5/16 inch) Figure 27 2. Hex-flange bolt (5/16 x 1 inch) 4. Secure the lower bracket of the left and right windshield supports to the machine using 4 carriage bolts (5/16 x 1 inch) and 4 flange nuts (5/16 inch) in the holes you drilled in step 1 (Figure 26). 1. Carriage bolt (5/16 x 2-3/4 inches) 3. Rear screen 2. Flange nut (5/16 inch) 4. Rear canopy support 6.
g214868 g217641 Figure 31 Figure 29 1. Carriage bolt (5/16 x 1-3/4 inches) 5. Rear mount bracket 2. Front mount bracket 3. Corner gusset 6. Crosslink tube 7. Windshield support 8. Loosely install the front mount brackets and front corner gussets to the crosslink tubes and the windshield supports using 8 carriage bolts (5/16 x 1-3/4 inches) and 8 flange nuts (5/16 inch) as shown in Figure 29. 9.
Important: Apply thread-locking compound 17 to the hex-flange bolts before installing. Important: Ensure that the plastic washers are installed onto the top and bottom of the sunshade, as this prevents damaging the sunshade. Installing the Canopy Parts needed for this procedure: 1 Sunshade 2 Clip 4 Sealing washer 4 Hex-flange bolt (1/4 x 1 inch) 2 Friction washer 4 Plastic washer 2 Flange bushing Procedure 1.
The Toro Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
