Service Bulletin

ManualsBrandsToro ManualsVehiclesWorkman 3200

Customer Service Bulletin

Commercial Business Group

Workman

3000/4000 Series

Date: August 15, 2002

Model/Serial Range: Model Numbers:

Serial Numbers:

07211 220000101-220099999

07212 220000101-220099999

07213 220000101-220099999

07214 220000101-220099999

07217 220000101-220099999

07218 220000101-220099999

Subject: Attachment Does Not Fit On 2002 HD Workman

The 2002 HD Workman Vehicle was repowered with Briggs & Stratton/Daihatsu Liquid

cooled gasoline and diesel engines. Due to changes in the engine compartment,

several attachments/accessories will require modification or adaptation kits. The PA-17

Spreader (41150), the Skid Sprayer (41220), and the 2002 1800 Topdresser (44225)

require following kits or modifications to mount on to the listed Workman vehicles:

PA-17 Spreader (41150) Adapted Handle (106-2419). This modified handle allows

spreader chute direction control. Remove the ROPS Cover Assembly (105-4237) when

used with the PA-17. The handle is installed like the original Lever Handle (92-8228)

with Lever Grip (92-8229), but requires no Pivot Lever Bracket (92-8223) or associated

linkages used with the original handle.

Skid Sprayer (41220) Adapter Kit (106-2510) provides adequate clearances between

the Skid Sprayer and the engine, muffler, cable routings and the lower radiator hose.

To allow access to the engine oil dipstick when the spray tank is loaded with material, a

door should be cut into the Skid Sprayer Tank Saddle Assembly (part no. 42878).

These modifications are only required to mount Skid Sprayers of model year 2002 and

older. Refer to the details contained in the Installation Instructions for Skid Sprayer

Adapter Kit (106-2510) for mounting direction.

Only model year 2002 1800 Topdressers (44225), require modification to create

clearances between the 1800 Topdresser frame and the carburetor on the gasoline

powered Briggs & Stratton/ Daihatsu engine. This clearance issue does not exist on the

B&S/D diesel powered engine or with the Kohler air-cooled engine. Modifications are

required to fit Hydraulic Filter Bracket (105-1747-03) in the High Flow Hydraulics Kit

(07228) when used in conjunction with the 2002 model 1800 Topdresser. See the

attached diagram for detailed instruction to perform these modifications, or contact your

Toro Commercial Products Distributor to perform these modifications.

High Air Intake Kit (106-2452) allows the installation of the high air intake assembly to

route around the ROPS Cover Assembly (105-4237) mounted on the ROPS bar. This

kit is used in place of High Air Intake Kit (94-5244) intended for 2001 and earlier model

year Mitsubishi powered Workman.

Ref: 17-14 Copyright



, 2002. The Toro Company

Summary of content (2 pages)

PAGE 1
Customer Service Bulletin Commercial Business Group Workman® 3000/4000 Series Model/Serial Range: Model Numbers: 07211 07212 07213 07214 07217 07218 Date: August 15, 2002 Serial Numbers: 220000101-220099999 220000101-220099999 220000101-220099999 220000101-220099999 220000101-220099999 220000101-220099999 Subject: Attachment Does Not Fit On 2002 HD Workman The 2002 HD Workman Vehicle was repowered with Briggs & Stratton/Daihatsu Liquid cooled gasoline and diesel engines.
PAGE 2
002 MODEL 1800 TOPDRESSER MODIFICATION INSTRUCTIONS For adapting to 2002 Workman 3000/4000 Series Vehicles 1. Empty all spreader material from the Topdresser and remove the Topdresser from the vehicle. 2. Support the Topdresser on a hard level surface with jack stands or similar to gain access the underside of the frame. 3. Cut off 3” (7.62 cm) from the steel rectangular tube intended to contain one of the forks from a forklift (on the passenger side tube only).