Form No. 3450-939 Rev A Workman® MDX Utility Vehicle Model No. 07235—Serial No. 410500000 and Up Model No. 07235TC—Serial No. 410500000 and Up Register at www.Toro.com.
This product complies with all relevant European directives; for details, please see the separate product specific Declaration of Conformity (DOC) sheet.
Introduction safety messages that you must follow to avoid accidents. This symbol will appear with the word Danger, Warning, or Caution. This utility vehicle is intended to be primarily used off-highway to transport people and material loads. Using this product for purposes other than its intended use could prove dangerous to you and bystanders. • Danger indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Contents Servicing the Battery......................................... 42 Replacing the Fuses ......................................... 43 Maintaining the Headlights ............................... 44 Drive System Maintenance .................................. 45 Maintaining the Tires ........................................ 45 Inspecting the Steering and Suspension Components ................................................. 45 Adjusting the Front Wheel Alignment ................
Safety This machine has been designed in accordance with the requirements of SAE J2258 (Nov 2016). General Safety This product is capable of causing personal injury. Always follow all safety instructions to avoid serious personal injury. • Read and understand the contents of this Operator’s Manual before you start the machine. Ensure that everyone using this product knows how to use it and understands the warnings. • Use your full attention while operating the machine.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal115-7739 115-7739 1. Falling, crushing hazard—do not carry passengers. decal99-7345 99-7345 1. Warning—read the Operator's Manual. 2. Warning—do not touch the hot surface. 3. Entanglement hazard, belt—stay away from moving parts; keep all guards in place. 4.
decal145-2269 145-2269 1. Off 3. To start the engine, sit in the operator's seat, disengage the parking brake, turn the key on, adjust the choke, and press the accelerator pedal. 2. On 4. To shut off the engine, release the accelerator pedal, engage the parking brake, turn the key off, and remove the key. decal145-2271 145-2271 1.
decal145-2277 145-2277 1. Warning—read the Operator’s Manual and receive training before operating the machine. 5. Falling hazard; severing hazard of hand or foot—do not carry passengers in the bed; do not carry a third passenger; do not put your hands or feet outside the machine while operating. 2. Warning—wear hearing protection. 6. Collision hazard—do not operate the machine on public streets, roads, or highways. 3. Fire hazard—shut off the engine before refueling. 7.
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 Description Use Qty. Steering wheel Cover Washer (1/2 inch) 1 1 1 Install the steering wheel (TC models only). No parts required – Connect the battery (TC models only). No parts required – Check the fluid levels and tire pressure. No parts required – Burnish (break-in) the brakes.
2 Connecting the Battery TC Models Only No Parts Required g228187 Procedure Figure 5 1. Insulator boot (positive battery cable) WARNING 2. Negative battery cable (black) Incorrectly routing the battery cable could damage the machine and cables, causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury. 4. • Always disconnect the negative battery cable (black) before disconnecting the positive battery cable (red). 5.
4 Burnishing the Brakes No Parts Required Procedure To ensure optimum performance of the brake system, burnish (break-in) the brakes before use. 1. Bring the machine up to full speed, apply the brakes to rapidly stop the machine without locking up the tires. 2. Repeat this procedure 10 times, waiting 1 minute between stops, to avoid overheating the brakes. Important: This procedure is most effective if the machine is loaded with 227 kg (500 lb).
Product Overview g033215 Figure 6 1. Hood latch 3. Cargo bed 5. Gear-shift selector 2. Parking-brake lever 4. Towing tongue 6. Fuel-tank cap 12 7.
Controls Become familiar with all the controls before you start the engine and operate the machine. Control Panel g382793 Figure 7 1. Horn switch 6. USB power point 2. Light switch 7. Parking-brake lever 3. Hour meter 8. Accelerator pedal 4. Engine oil-pressure Light 9. Brake pedal 5. Key switch CAUTION Accelerator Pedal Operating a machine with worn or incorrectly adjusted brakes can may result in personal injury. Use the accelerator pedal (Figure 7) to vary the ground speed of the machine.
Choke Control Key Switch The choke control is located below and to the right of the operator's seat. Use the choke to help start a cold engine by pulling the choke control outward (Figure 8). After the engine starts, adjust the choke to keep the engine running smoothly. As the engine warms up, push in the choke control to the OFF position. The key switch is located at the lower, right corner of the dash panel (Figure 7). The key switch has 3 positions: OFF, ON, and START .
Fuel Gauge The fuel gauge (Figure 9) is located on the fuel tank next to the filler cap, at the left side of the machine. The gauge displays the amount of fuel in the tank. g008398 Figure 9 1. Empty 4. Fuel gauge 2. Full 5. Fuel-tank cap 3. Needle Passenger Handholds The passenger handholds are located on the right side of the dash panel and at the outside of each seat (Figure 10). g009193 Figure 10 1. Handhold—hip restraint 2.
Specifications Note: Specifications and design are subject to change without notice. Base weight Dry 544 kg (1,200 lb) Rated capacity (on level ground) 749 kg (1,650 lb) total, including 90.7 kg (200 lb) operator and 90.
Performing Daily Maintenance Operation Note: Determine the left and right sides of the machine from the normal operating position. Service Interval: Before each use or daily Before Operation Before starting the machine each day, perform the Each Use/Daily procedures listed in Maintenance (page 26).
Adding Fuel Recommended fuel: 5. Remove the fuel-tank cap. 6. Fill the tank to about 25 mm (1 inch) below the top of tank, (bottom of the filler neck). • For best results, use only clean, fresh (less than Note: This space in the tank allows fuel to expand. Do not overfill the fuel tank. 30 days old), unleaded gasoline with an octane rating of 87 or higher ((R+M)/2 rating method). • Ethanol: Gasoline with up to 10% ethanol (gasohol) or 15% MTBE (methyl tertiary butyl ether) by volume is acceptable.
During Operation During Operation Safety • General Safety • The owner/operator can prevent and is responsible • • • • • • • • • • • • • for accidents that may cause personal injury or property damage. Passengers should sit in the designated seating positions only. Do not carry passengers in the cargo bed. Keep bystanders and children out of the operating area. Wear appropriate clothing, including eye protection; long pants; substantial, slip-resistant footwear; and hearing protection.
in weight distribution may cause the machine to overturn. a rollover. Contact an authorized Toro distributor for more information. Slopes are a major factor related to loss-of-control and tip-over accidents, which can result in severe injury or death. Operating the Cargo Bed • Survey the site to determine which slopes are Raising the Cargo Bed safe for operating the machine and establish your own procedures and rules for operating on those slopes.
Opening the Tailgate 1. Ensure that the cargo bed is down and latched. 2. Lift up the finger pulls at the back panel of the tailgate (Figure 15). g014860 Figure 13 1. Lever 2. Prop rod 2. 3. Detent slot Pull the prop rod into the detent slot to secure the bed (Figure 14). g024490 Figure 15 1. Tailgate flange (cargo bed) 3. Lift up (finger pull) 2. Lock flange (tailgate) 4. Rotate rearward and down 3.
Note: When using key start mode, you can engage the parking brake and work away from the machine while the engine still runs and the battery holds a charge. Note: If you turn the key to the START position, the engine cranks until it starts. If the engine cranks for more than 10 seconds, return to the OFF position, and determine the issue (e.g., the choke controls needs to be engaged, check the air cleaner for restrictions, ensure that the fuel tank is full, the spark is bad, etc.
Loading the Cargo Bed Material Density Maximum Cargo Box Capacity (on level ground) Gravel, dry 1522 kg/m3 (95 lb/ft3) Full limit the weight of the load that you carry in the cargo bed as described in Specifications (page 16) and on the gross vehicle weight tag of the machine.
After Operation After Operation Safety General Safety • Before you leave the operating position, do the • • • • • following: – Park the machine on a level surface. – Shift the transmission to the NEUTRAL position. – Engage the parking brake. – Shut off the machine and remove the key. – Wait for all movement to stop. Allow the machine to cool before adjusting, servicing, cleaning, or storing it.
Towing the Machine Towing a Trailer In case of an emergency, you can tow the machine for a short distance; however, this should not be a standard operating procedure. The machine is capable of pulling trailers. A tow hitch is available for the machine. Contact your Authorized Service Dealer for details. When hauling cargo or towing a trailer, do not overload your machine or trailer.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Maintenance Safety • If you must run the machine to perform a maintenance adjustment, keep your hands, feet, clothing, and any parts of the body away from any moving parts. Keep bystanders away from the machine. • Do not allow untrained personnel to service the • • • • • • • • machine. Before you leave the operating position, do the following: – Park the machine on a level surface.
Maintenance Service Interval Maintenance Procedure Every 100 hours • • • • • • • • • • • • • Replace the air filter. Replace the air-filter element sooner if it dirty or damaged. Change the engine oil. Change the engine-oil filter. Check the spark plugs. Check the air filter for the carbon canister. Check the condition of the tires and rims. Torque the wheel-lug nuts. Inspect the steering and suspension for loose or damaged components. Check the front wheel camber and toe-in.
Daily Maintenance Checklist Duplicate this page for routine use. Maintenance Check Item For the week of: Monday Tuesday Wednesday Thursday Friday Saturday Sunday Check the brake and parking brake operation. Check the gear shift/neutral operation. Check the fuel level. Check the engine-oil level. Check the brake-fluid level. Check the transaxle-fluid level. Inspect the air filter. Inspect the engine-cooling fins. Check for unusual engine noises. Check for unusual operating noises.
Pre-Maintenance Procedures Many of the subjects covered in this maintenance section require raising and lowering the bed. To prevent serious injury or death, take the following precautions. Preparing the Machine for Maintenance 1. Park the machine on a level surface. 2. Shift the transmission to the NEUTRAL position. 3. Engage the parking brake. 4. Shut off the engine and remove the key. 5. Empty and raise the cargo bed. g033043 Figure 19 1.
Accessing the Hood Lubrication Raising the Hood Greasing the Front Wheel Bearings 1. Lift up the handle of the rubber latches on each side of the hood (Figure 21). Service Interval: Every 300 hours Grease specification: Mobilgrease XHP™-222 Removing the Hub and Rotor 1. Lift the front of the machine and support it with jack stands. 2. Remove the 4 lug nuts that secure the wheel to the hub (Figure 22). g312721 Figure 21 2. Raise the hood. Closing the Hood 1. Gently lower the hood. 2.
g033049 Figure 25 1. Spindle 2. Hub and rotor assembly g033047 Figure 23 1. Flange-head bolts (3/8 x 3/4 inch) 3. Caliper bracket (brake assembly) 2. Spindle 4. Remove the dust cap from the hub (Figure 24). g033048 Figure 24 1. Cotter pin 4. Spindle nut 2. Spindle 5. Nut retainer 3. Tab washer 6. Dust cap 5. Remove the cotter pin and nut retainer from the spindle and spindle nut (Figure 24). 6.
Installing the Hub and Rotor Greasing the Wheel Bearings 1. 1. Remove the outboard bearing and bearing race from the hub (Figure 26). Apply a light coat of the specified grease to the spindle (Figure 27). g033050 Figure 26 g033051 Figure 27 1. Seal 4. Bearing cavity (hub) 2. Inboard bearing 5. Outboard-bearing race 1. Nut retainer 4. Outer bearing 3. Inboard-bearing race 6. Outboard bearing 2. Spindle nut 5. Hub, rotor, inner bearing, race, and seal 6. Spindle 3. Tab washer 2.
Engine Maintenance Engine Safety • Shut off the engine, remove the key, and wait for all moving parts to stop before checking the oil or adding oil to the crankcase. • Keep your hands, feet, face, clothing, and other body parts away from the muffler and other hot surfaces. Servicing the Air Filter g033054 Figure 28 1. Cotter pin Service Interval: Every 100 hours Replace the air-filter element sooner if it dirty or damaged. 3. Dust cap 2. Nut retainer 9.
1. Clean the dirt ejection port located on the air-filter cover. 2. Remove the rubber outlet valve from the cover, clean the cavity, and replace the outlet valve. 3. Insert the air-filter element into air-filter housing (Figure 30). Note: Ensure that the filter is sealed properly by applying pressure to the outer rim of the filter when installing it. Do not press on the flexible center of the filter. g027733 4. Align the air-filter cover with the air-filter housing (Figure 30). 5.
Servicing the Engine Oil Service Interval: After the first 25 hours Every 100 hours (Change the oil twice as often during special operating conditions; refer to Maintaining the Machine under Special Operating Conditions (page 28). Note: Change the oil more frequently when operating conditions are extremely dusty or sandy. g002132 Note: Dispose of the used engine oil and oil filter at a Figure 32 certified recycling center. 1. Oil dipstick (loop down) Engine-Oil Specifications 4.
Servicing the Spark Plugs Service Interval: Every 100 hours/Yearly (whichever comes first) Replace the spark plugs if necessary. Type: Champion RN14YC (or equivalent) Air Gap: 0.762 mm (0.03 inch) Important: A cracked, fouled, dirty, or malfunctioning spark plug must be replaced. Do not sand-blast, scrape, or clean electrodes by using a wire brush because grit may eventually release from the plug and fall into the cylinder. The result is usually a damaged engine. g009200 Figure 33 1. Drain plug 7. 2.
Adjusting the High/Low Idle Fuel System 1. Lift the cargo bed and secure it open with the prop rod. Maintenance 2. With the machine off, fully press the accelerator pedal and measure the gap between the leading edge of the governor bellcrank and the bracket tab. Inspecting Fuel Lines and Connections This gap should be between 0.8 to 2.0 mm (.03 to .08 inches).
Servicing the Carbon Canister Checking the Air Filter for the Carbon Canister Service Interval: Every 100 hours—Check the air filter for the carbon canister. Check the opening at the bottom of the air filter for the carbon canister to ensure that it is clean and free of debris and obstructions (Figure 37). g024478 Figure 38 1. Carbon-canister filter 2. Carbon canister 2. g014998 Figure 37 1.
Replacing the Carbon Canister Note: Replace the carbon canister if it is damaged, plugged, or if the machine is run without a carbon-canister filter. Note: Replace the carbon-canister filter when replacing the carbon canister. Disconnecting the Controls at the Seat Base 1. Remove the knob from the gear-shift lever (Figure 39). g029670 Figure 40 1. Cable tie 2. Parking-brake cable 6. Front of the machine 7. Clevis 3. Forward-jam nut 8. Cotter pin 4. Brake-cable bracket 9. Clevis pin 5.
2. Carefully lift the seats, seat base, and parking brake cables from the machine (Figure 41). Important: Note the routing of the parking-brake cables along the chassis as you lift the seats and seat base from the machine. g029659 Figure 42 g029628 Figure 44 1. Carbon canister 2. Carbon-canister mount (fuel tank) Replacing the Carbon Canister 1. Remove the vacuum hose from the fitting on the carbon canister marked Purge (Figure 43). 4. 3.
7. Insert the new carbon canister into the carbon-canister mount of the fuel tank with the purge and fuel tank fittings aligned rearward (Figure 44). 8. Assemble the vacuum hose onto the fitting on the carbon canister marked Purge and the fuel-tank hose to the onto the fitting marked Fuel Tank (Figure 43). 4. Installing the Seats and Seat Base 1. Lift the seats and seat base onto the machine and align brake cables to the chassis (Figure 41 and Figure 42). 2.
Electrical System Maintenance WARNING Battery terminals or metal tools could short against metal machine components, causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury. • When removing or installing the battery, do not allow the battery terminals to touch any metal parts of the machine. • Do not allow metal tools to short between the battery terminals and metal parts of the machine. Electrical System Safety • Disconnect the battery before repairing the machine.
Replacing the Fuses Installing the Battery 1. Align the battery to the battery tray of the machine (Figure 46). There are 4 fuses in the electrical system. They are located beneath the hood (Figure 47). Note: Ensure that the positive and negative posts of the battery are aligned as shown in Figure 46. 2. 3. Secure the battery to the battery tray with the battery clamp, carriage bolt, and locknut (Figure 46).
Maintaining the Headlights 7. Secure the headlight assembly with the speed clips that you removed in step 4. Replacing the Headlight 8. Connect the electrical connector for the harness to the connector of the lamp assembly (Figure 48). 9. Adjust the headlights to direct the beams to the desired position, refer to Adjusting the Headlights (page 44). Specification: See your Parts Catalog. 1. Disconnect the battery; refer to Disconnecting the Battery (page 42). 2. Open the hood. 3.
Drive System Maintenance Maintaining the Tires Service Interval: Every 100 hours—Check the condition of the tires and rims. Every 100 hours—Torque the wheel-lug nuts. 1. Inspect the tires and rims for signs of wear and damage. Note: Operating accidents, such as hitting curbs, can damage a tire or rim and also disrupt wheel alignment, so inspect tire condition after an accident. g313199 2. Figure 50 Torque the wheel lug nuts to 108 to 122 N∙m (80 to 90 ft-lb). 1.
Adjusting the Front Wheel Alignment Adjusting the Front Wheel Toe-in Important: Before adjusting toe-in, ensure that the camber adjustment is as close to neutral as possible; refer to Adjusting the Camber (page 46). Service Interval: Every 100 hours/Yearly (whichever comes first)—Check the front wheel camber and toe-in. 1. Preparing to Adjust Camber or Toe-in 1. Check the tire pressure to ensure that the front tires are inflated to 82 kPa (12 psi). 2.
Checking the Transaxle-Fluid Level Service Interval: Every 100 hours Fluid Type: SAE 10W30 (API service SJ or higher) 1. 2. Park the machine on a level surface, shift the transmission to the NEUTRAL position, engage the parking brake, shut off the engine, and remove the key. g002109 Figure 56 Remove the bolt from the level-indicating hole (Figure 55). 1. Drain plug Note: The transaxle fluid level should be at the bottom of the level indicator hole. 3. Align a drain pan with a capacity of 2 L (2.
10. Check the fluid level and add more fluid if the level is below the threads of the fill-plug hole (Figure 56). 5. Checking and Adjusting Neutral Pull up on each shift cable an ensure that there is a 0.76 to 1.52 mm (0.03 to 0.06 inch) between the nut/washer and the neutral bracket (Figure 59). Note: If there is a not a gap, adjust the nuts to achieve the specified gap.
g026341 Figure 61 g011947 1. Clutch spacer Figure 60 1. Cover 2. Bolts 3. Remove the spring. Add or remove spacers to adjust the top speed. Use the following table to determine the amount of spacers needed. 3. Thoroughly clean the inside of the cover and the inner components of the clutch using compressed air. 4. 4. Install the clutch cover and secure it with the 3 bolts (Figure 60) that you removed in 2. Spacers Top Speed 2 (standard) 16 mph (standard) Lower the cargo bed.
Cooling System Maintenance Brake Maintenance Cooling System Safety Service Interval: Every 100 hours Inspecting the Brakes Important: Brakes are a critical safety component • Swallowing engine coolant can cause poisoning; of the machine. Closely inspect them at the recommended service interval to ensure optimum performance and safety. keep out of reach from children and pets. • Discharge of hot, pressurized coolant or touching a hot radiator and surrounding parts can cause severe burns.
4. procedure for adjusting the brake cables; refer to Adjusting the Brake Cables (page 51). parking-brake lever with a a force of 133 to 156 N (30 to 35 lbf), perform the following: Tighten the set screw and install the hand grip (Figure 62). A. Loosen the rear jam nut (Figure 63) for the threaded adjuster of the parking-brake cable 1 turn. B. Tighten the forward jam nut (Figure 63). C.
Checking the Brake-Fluid Level B. Add DOT 3 brake fluid to the reservoir until the fluid level is above the Minimum line (Figure 65). Note: Do not overfill the reservoir with brake fluid. Service Interval: Before each use or daily—Check the brake-fluid level. Check the brake-fluid level before you first start the engine. C. 7. Brake-fluid type: DOT 3 Install the reservoir cap (Figure 64). Close the hood. 1. Park the machine on a level surface. 2. Engage the parking brake.
Belt Maintenance Servicing the Drive Belt Rotate and route the belt over the secondary clutch (Figure 66). 7. Lower the cargo bed. Adjusting the Starter-Generator Belt Checking the Drive Belt Service Interval: After the first 8 hours Service Interval: After the first 8 hours Every 200 hours 1. 6. Every 200 hours Park the machine on a level surface, engage the parking brake, shut off the engine, and remove the key. 2. Raise the cargo bed and secure it with the prop rod. 3.
Chassis Maintenance Cleaning Adjusting the Cargo-Bed Latches Washing the Machine Service Interval: Before each use or daily—Wash the machine. If the cargo-bed latch is out of adjustment, the cargo bed vibrates up and down as you drive the machine. You can adjust the latch posts to make the latches hold the cargo bed snugly to the chassis. 1. Wash the machine as needed using water alone or with a mild detergent. You may use a rag when washing the machine.
Storage A fully charged battery maintains its charge for about 50 days at temperatures lower than 4°C (40°F). If the temperatures will be below 4°C (40°F), charge it every 30 days. Storage Safety • Shut off the machine, remove the key, and wait for all movement to stop before you leave the operator’s position. Allow the machine to cool before adjusting, servicing, cleaning, or storing it. 12. Check and tighten all bolts, nuts, and screws. Repair or replace any part that is damaged. 13.
Notes:
Notes:
EEA/UK Privacy Notice Toro’s Use of Your Personal Information The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer.
California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.
The Toro Warranty Two-Year or 1,500 Hours Limited Warranty Parts Conditions and Products Covered The Toro Company warrants your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for 2 years or 1,500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
